Microchip Technology

LAN9255-V/ZMX018 EtherCAT Controller | Microchip Technology

N.º de pieza: LAN9255-V/ZMX018 ✓ Activo
3.3 V Vdss 128-pin TQFP with exposed pad Package 256K Memory
MOQ: 1 |

LAN9255-V/ZMX018 Descripción general

The Microchip Technology LAN9255-V/ZMX018 is an EtherCAT device controller with an integrated 32-bit Arm Cortex-M4F microcontroller, 256K programmable memory, and dual 100BASE-TX Ethernet PHYs. It operates from a 3.3 V supply, supports IEEE 802.3, USB 2.0, RMII, and EtherCAT connectivity, and is packaged in a 128-pin TQFP with an exposed pad. The device combines a 2/3-port EtherCAT slave controller and SAM E53J-class microcontroller functions in one package.

An EtherCAT device controller is an integrated circuit used to connect automation equipment to an EtherCAT industrial Ethernet network. It processes EtherCAT frames, provides real-time fieldbus connectivity, and supervises physical-layer communication. Within the product hierarchy, the LAN9255 is a network controller, EtherCAT device controller, Ethernet controller, and industrial communications IC with integrated MCU and dual PHYs.

The integrated Cortex-M4F processor gives the design direct access to EtherCAT processing and application-control functions rather than requiring a separate host microcontroller. Its 256K programmable memory supports firmware and protocol tasks, while the dual PHYs each support full-duplex 100BASE-TX operation at 100 Mbps. The integrated architecture reduces inter-device data paths and supports compact industrial slave-controller implementations.

The -V ordering option is specified for an extended-industrial temperature range of -40°C to +105°C. The ZMX package designation identifies a 128-pin TQFP configuration, while 018 identifies the 256K programmable-memory configuration. The package exposes the signals of the EtherCAT controller and microcontroller sections and uses an exposed pad for improved package-level heat spreading.

Typical applications include EtherCAT slave modules, industrial I/O devices, motion-control equipment, servo-drive interfaces, PLC expansion modules, and factory-automation controllers. The dual 100BASE-TX PHYs suit EtherCAT line topology implementations in which devices forward frames through successive Ethernet ports. The integrated microcontroller also enables application logic, diagnostics, and EtherCAT stack execution in a single device.

Hardware design should follow the Microchip LAN9255 Hardware Design Checklist, including correct exposed-pad soldering, multilayer board construction, controlled-impedance Ethernet routing, suitable decoupling, and isolation between PHY and digital sections. Confirm the required EtherCAT topology, cable characteristics, termination strategy, firmware configuration, and thermal performance before releasing a production PCB.

This product overview combines the manufacturer specifications, ordering-code structure, application guidance, drop-in configuration alternatives, and practical PCB considerations into one engineering reference for EtherCAT controller selection and implementation.

Alternativas directas para LAN9255-V/ZMX018 — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.

Variantes de esta serie

Modelos de la misma serie compatibles directamente con LAN9255-V/ZMX018 (mismo factor de forma y huella) — difiere en Package, Operating Temperature, Integrated MCU, Supply Voltage, EtherCAT Port Configuration.

Microchip Technology
Package: 128-pin TQFP, 14 x 14 mm
Microchip Technology
Package: 128-TQFP (14x14 mm)
Operating Temperature: -40 C to +85 C (Industrial)
Integrated MCU: Microchip SAM E53J ARM Cortex-M4F with FPU
Microchip Technology
Package: 128-pin TQFP (ZMX), 14 x 14 mm
Operating Temperature: -40°C to +105°C (Extended Industrial, -V)
Integrated MCU: SAM E53J with 32-bit Arm Cortex-M4F core
Microchip Technology
Package: 128-TQFP-EP (14x14 mm)
Operating Temperature: -40C to +85C (industrial)
Integrated MCU: SAM E53J ARM Cortex-M4F

LAN9255-V/ZMX019

✅ Sustitución directa
Microchip Technology
📦 128-TQFP (14x14)
2/3-port EtherCAT device controller · SAM E53J with 32-bit Arm Cortex-M4F core · 2 full-duplex 100BASE-TX transceivers · 100 Mbps · 2 or 3 ports · 512K · 3.3 V · -40°C to +105°C (Extended Industrial, -V)

Consulte el precio

Ver hoja de datos →

LAN9255-V/ZMX020

✅ Sustitución directa
Microchip Technology
📦 128-TQFP (14x14)
EtherCAT Slave Controller with integrated MCU · EtherCAT (IEC 61158) · 2/3 ports (EtherCAT) · Dual integrated 100BASE-TX · 100 Mbps full-duplex · SAM E53J ARM Cortex-M4F · 32-bit ARM Cortex-M4F with FPU · 1024 KB

Consulte el precio

Ver hoja de datos →

LAN9255-I/ZMX019

✅ Sustitución directa
Microchip Technology
📦 128-TQFP (14x14)
2/3-Port EtherCAT Device Controller (ESC) with integrated dual PHYs and ARM Cortex-M4F MCU · 2 external ports (Port 0, Port 1) + 1 cascaded/loopback Port 2 · Dual integrated 100BASE-TX transceivers, full-duplex · 100 Mbps (100BASE-TX) · USB 2.0 Full-Speed (12 Mbps), RMII · Microchip SAM E53J ARM Cortex-M4F with FPU · 512 kB · IEEE 802.3, USB 2.0, RMII, SPI (host)

Consulte el precio

Ver hoja de datos →

LAN9255-I/ZMX020

✅ Sustitución directa ⚠️ Especificaciones sin verificar
Microchip Technology
📦 128-TQFP (14x14)
2/3-port EtherCAT device controller with integrated MCU · SAM E53J 32-bit Arm Cortex-M4F · 20 MHz · 1.024 MB · IEEE 802.3 · 100 Mbps · Dual 100BASE-TX PHYs · Full duplex

Consulte el precio

Ver hoja de datos →

LAN9255-I/ZMX018

✅ Sustitución directa
Microchip Technology
📦 128-TQFP (14x14)
2/3-port EtherCAT device controller · 32-bit Arm Cortex-M4F · 256 kB · 2 full-duplex 100BASE-TX PHYs · 100 Mbps · IEEE 802.3 · USB 2.0 · RMII

Consulte el precio

Ver hoja de datos →

LAN9255-V/ZMX018 Especificaciones

Product Type EtherCAT device controller with integrated microcontroller
EtherCAT Port Configuration 2/3-port
Integrated MCU Core 32-bit Arm Cortex-M4F
Programmable Memory 256K
Tensión de alimentación 3.3 V
Ethernet Data Rate 100 Mbps
Integrated PHY Count 2
PHY Standard IEEE 802.3 100BASE-TX
PHY Duplex Mode Full duplex
Host Interface RMII
USB Interface Standard USB 2.0
Temperatura de funcionamiento -40°C to +105°C
Encapsulado 128-pin TQFP with exposed pad
Package Body Size 14 mm x 14 mm
Tipo de montaje Surface mount
Moisture Sensitivity Level MSL 3, 168 hours
Export Control Classification EAR99

Guía de configuración de pines de LAN9255-V/ZMX018 14 mm x 14 mm

Configuración de pines para LAN9255-V/ZMX018 (encapsulado 14 mm x 14 mm). La numeración de pines, las funciones y los diagramas de conexión se definen en la hoja de datos del fabricante. Consúltela para conocer el footprint exacto y las directrices de soldadura.

Diagrama de patillaje del encapsulado 14 mm x 14 mm para LAN9255-V/ZMX018

No hay datos detallados de patillaje disponibles para LAN9255-V/ZMX018.

Consulte la hoja de datos para ver la configuración completa de patillas.

Aplicaciones típicas

LAN9255-V/ZMX018 es adecuado para 6 aplicacións: EtherCAT Industrial I/O Module, Servo Drive EtherCAT Interface, PLC Communication Gateway, Motion-Control Terminal, Machine Vision Network Interface, Industrial Sensor Network Controller.

🏭

EtherCAT Industrial I/O Module

The LAN9255-V/ZMX018 fits distributed industrial I/O modules because it combines an EtherCAT device controller, Cortex-M4F processor, and two 100Mbps full-duplex PHYs in one 128-pin TQFP device. The processor can run the EtherCAT stack and channel-control firmware, while 256K of programmable memory supports configuration, diagnostics, and application logic. Its -40°C to +105°C rating suits factory-floor equipment. Place the Ethernet pairs on controlled-impedance routing and follow the manufacturer exposed-pad and decoupling guidance.

⚙️

Servo Drive EtherCAT Interface

For compact servo-drive controllers, the LAN9255-V/ZMX018 provides the real-time EtherCAT endpoint and application-control core in one package. Its dual 100BASE-TX PHYs support the line-oriented Ethernet connections used in multi-axis systems, and the 3.3 V supply integrates with low-voltage digital power domains. The 256K memory configuration is useful for motion-control firmware when final code size remains comfortably below capacity. Validate deterministic timing, thermal rise, and Ethernet signal integrity during axis-drive qualification.

🔧

PLC Communication Gateway

The LAN9255-V/ZMX018 can implement a dedicated PLC-to-EtherCAT gateway because its Cortex-M4F executes protocol conversion while the EtherCAT controller handles distributed-network communication. Two integrated 100Mbps PHYs reduce the need for additional Ethernet components, and the 256K memory capacity accommodates firmware, mapping tables, and diagnostics. RMII and USB 2.0 connectivity provide additional host-facing options. Confirm the required gateway topology, watchdog strategy, and recovery behavior during system validation.

🤖

Motion-Control Terminal

The LAN9255-V/ZMX018 supports compact motion-control terminals that need deterministic EtherCAT participation close to the application processor. Its Cortex-M4F handles stack tasks and local control functions, while the dual PHYs provide 100Mbps full-duplex links over industrial Ethernet cabling. The integrated architecture reduces board area compared with separate controller and MCU implementations. Use the 1024K memory variant when diagnostics, coordinate tables, or update buffers exceed the 256K target's comfortable code and data capacity.

📷

Machine Vision Network Interface

The LAN9255-V/ZMX018 can serve as the EtherCAT and Ethernet coordination element in a machine-vision interface, combining real-time device control with local Cortex-M4F processing. Its two 100BASE-TX PHYs support industrial cable connections at 100Mbps, and the 256K memory configuration supports protocol firmware and local status management. The -40°C to +105°C range is appropriate for enclosure temperatures encountered near industrial machinery. Maintain controlled-impedance Ethernet routing and validate EMI behavior alongside the imaging subsystem.

🧩

Industrial Sensor Network Controller

For distributed sensor networks, the LAN9255-V/ZMX018 combines EtherCAT slave-controller behavior with an application microcontroller and dual integrated Ethernet PHYs. The Cortex-M4F can collect measurements, maintain device state, and execute the EtherCAT stack without requiring a separate host MCU. The 100Mbps PHY rate is suitable for standard 100BASE-TX industrial Ethernet segments, while the 128-pin TQFP keeps the controller footprint compact. Confirm cable length, grounding, isolation, and thermal conditions for the installed sensor topology.

What is the LAN9255-V/ZMX018?
The LAN9255-V/ZMX018 is a Microchip Technology EtherCAT device controller integrating a 32-bit Arm Cortex-M4F microcontroller, 256K programmable memory, and two 100BASE-TX PHYs. According to Microchip datasheet 00003646B, it supports 100 Mbps full-duplex Ethernet, EtherCAT operation, RMII, and USB 2.0 interfaces. The device is packaged in a 128-pin TQFP with an exposed pad and operates from a 3.3 V supply.
What does the 018 suffix mean in LAN9255-V/ZMX018?
The 018 suffix identifies the 256K programmable-memory configuration of the LAN9255 family. According to Microchip datasheet 00003646B, the LAN9255 memory order codes are 018 for 256K, 019 for 512K, and 020 for 1024K programmable memory. These variants retain the same EtherCAT controller and dual-PHY architecture, allowing engineers to scale firmware and application storage without changing the device family.
How many Ethernet PHYs does the LAN9255-V/ZMX018 contain?
The LAN9255-V/ZMX018 contains two integrated Ethernet PHYs, and each PHY supports full-duplex 100BASE-TX operation at 100 Mbps. Microchip describes the LAN9255 as a 2/3-port EtherCAT device controller, with the integrated PHYs supporting the physical connections used by EtherCAT line topologies. The exact signal assignments and port-routing options are defined in Microchip datasheet 00003646B.
Where can I download the LAN9255-V/ZMX018 datasheet PDF?
The official LAN9255 datasheet is available from Microchip at https://ww1.microchip.com/downloads/en/DeviceDoc/00003646B.pdf. It covers device specifications unique to the LAN9255, package and ordering information, the integrated Cortex-M4F microcontroller, PHYs, and EtherCAT functionality. Use the manufacturer document together with the LAN9255 Hardware Design Checklist when planning the PCB and power-delivery network.
Where can I find the LAN9255-V/ZMX018 pinout?
The LAN9255-V/ZMX018 pin assignments are published in Microchip datasheet 00003646B and the associated LAN9255 Hardware Design Checklist. The device uses a 128-pin TQFP package with an exposed pad, and all controller and MCU signals are exposed on package pins. Use the manufacturer pin-description table when assigning PCB nets and verify the exposed-pad connection and thermal-land pattern against the package drawing.
Is the LAN9255-V/ZMX018 suitable for industrial automation?
Yes, the LAN9255-V/ZMX018 is suitable for industrial EtherCAT equipment operating from -40°C to +105°C. Its dual 100BASE-TX PHYs support EtherCAT line networking at 100 Mbps, while the integrated Cortex-M4F and 256K memory consolidate slave-controller and application-control functions. It is well suited to distributed I/O, motion-control gateways, servo interfaces, and PLC-connected automation modules.
What can replace the LAN9255-V/ZMX018?
LAN9255-V/ZMX019 and LAN9255-V/ZMX020 are pin-compatible same-family alternatives that provide 512K and 1024K programmable memory, respectively. They retain the 128-pin TQFP package and EtherCAT controller with dual 100BASE-TX PHYs, but require more firmware and data storage than the 256K target. Confirm memory requirements and the exposed-pad footprint before treating either option as a drop-in replacement.
Is LAN9255-V/ZMX019 a drop-in replacement for LAN9255-V/ZMX018?
LAN9255-V/ZMX019 is a same-package drop-in alternative for LAN9255-V/ZMX018 when the board can operate with a larger memory configuration. The principal difference is programmable memory, increasing from 256K to 512K, a 100% increase. Both use the 128-pin TQFP package, integrated dual 100BASE-TX PHYs, 3.3 V supply, and Cortex-M4F microcontroller.
LAN9255-V/ZMX018 vs LAN9255-V/ZMX020: which should I choose?
Choose LAN9255-V/ZMX018 when 256K of programmable memory is sufficient; choose LAN9255-V/ZMX020 when the application needs 1024K, which is a 300% memory increase. Both provide the same 128-pin TQFP footprint, EtherCAT controller, dual 100Mbps full-duplex PHYs, RMII interface, and Cortex-M4F core. The larger-memory device is preferable for complex firmware, diagnostics, or multiple protocol stacks.
When should I choose LAN9255-V/ZMX018 instead of a larger-memory LAN9255 variant?
Choose LAN9255-V/ZMX018 when firmware and runtime data fit within 256K of programmable memory and minimizing internal memory requirements is important. The larger 512K and 1024K variants provide more design headroom but do not change the 128-pin TQFP footprint. Choose the target only after checking linker-map utilization, update storage, diagnostics buffers, and long-term firmware growth.
Is there a Microchip equivalent with the same package and more memory?
Microchip's LAN9255-V/ZMX019 and LAN9255-V/ZMX020 provide 512K and 1024K programmable memory while retaining the 128-pin TQFP package and dual-PHY EtherCAT architecture. The memory increases are 100% and 300%, respectively, compared with the 256K LAN9255-V/ZMX018. They are appropriate when the existing board layout is acceptable and the firmware needs additional storage.
What is the power supply requirement for the LAN9255-V/ZMX018?
The LAN9255-V/ZMX018 operates from a 3.3 V supply. The device integrates a 3.3 V Ethernet controller, Cortex-M4F microcontroller, and two PHY sections, so a robust 3.3 V rail with local high-frequency decoupling is required. Follow the decoupling and exposed-pad recommendations in Microchip datasheet 00003646B and the LAN9255 Hardware Design Checklist for production layout implementation.
Does the LAN9255-V/ZMX018 require an external microcontroller?
No separate application microcontroller is required for the controller function because the LAN9255-V/ZMX018 integrates a 32-bit Arm Cortex-M4F with 256K programmable memory. This consolidation supports EtherCAT stack execution, diagnostics, and application logic in one package. Additional external processing may still be useful when the application exceeds the available memory, processing, or external interface requirements.
Where can I buy the LAN9255-V/ZMX018?
Use the Request a Quote form on this page to request the LAN9255-V/ZMX018, current availability, lead time, and order quantities from XAIPART. The exact ordering code includes the -V temperature option, ZMX 128-pin TQFP package, and 018 memory configuration. Include your target quantity and packaging preference in the request to obtain an appropriate supply response.
What is the price of the LAN9255-V/ZMX018?
The current price and volume structure for the LAN9255-V/ZMX018 are presented through XAIPART's Request a Quote form on this page. Submit the required quantity, tray or other packaging preference, and delivery location to obtain a current quotation. This approach also allows the supplier to confirm stock, lead time, and traceability requirements for the exact ordering code.
What is the lead time and stock status of the LAN9255-V/ZMX018?
Request current stock and lead-time confirmation through the Request a Quote form on this page. Quote timing can vary with the requested quantity, allocation, package format, and destination, so a production schedule should not rely on generic marketplace availability. Include your required delivery date and any inspection or traceability requirements when submitting the request.
Is the LAN9255-V/ZMX018 RoHS and REACH compliant?
The LAN9255-V/ZMX018 listing identifies its REACH status, while the precise compliance declaration should be confirmed against the current Microchip product and material declarations. The component is supplied in a 3.3 V, 128-pin TQFP industrial package and is listed under EAR99 export classification. Use the manufacturer declarations and your assembly provider's current compliance records for formal qualification.
How should the LAN9255-V/ZMX018 PCB be designed?
The LAN9255-V/ZMX018 PCB should implement the manufacturer's exposed-pad land pattern, local 3.3 V decoupling, controlled-impedance 100BASE-TX routing, and the separation measures described in the Microchip LAN9255 Hardware Design Checklist. Keep the Ethernet pairs geometry-controlled and inspect the assembly process for complete exposed-pad solder fillet formation. Thermal performance depends on the multilayer stack-up and copper area, so include the thermal interface in board-level validation.

Datos de referencia de ingeniería para LAN9255-V/ZMX018 — comparación, orientación de diseño e información de cumplimiento.

Guía de selección

Choose LAN9255-V/ZMX018 for an EtherCAT slave or gateway design whose firmware fits comfortably within 256K of programmable memory and whose operating requirements match the -V ordering option. Its integrated Cortex-M4F, dual 100BASE-TX PHYs, and 3.3 V architecture simplify industrial Ethernet implementations while preserving a single 128-pin TQFP footprint. Select LAN9255-V/ZMX019 when the firmware, mapping tables, or diagnostics need 512K, a 100% memory increase without a PCB change. Select LAN9255-V/ZMX020 for 1024K when larger update images, diagnostics buffers, or application stacks are required. The I-ordering variants provide the same broad controller and package platform but use a different temperature-option code. Confirm the final ordering code against the required temperature grade, firmware footprint, exposed-pad layout, and production availability before committing the design.

Comparación con alternativas

Parámetro Este producto LAN9255-V/ZMX019 LAN9255-V/ZMX020 LAN9255-I/ZMX019 LAN9255-I/ZMX020
Brand Microchip Technology Microchip Technology Microchip Technology Microchip Technology Microchip Technology
Package 128-TQFP (14x14) 128-TQFP (14x14) 128-TQFP (14x14) 128-TQFP (14x14) 128-TQFP (14x14)
Programmable Memory 256K 512K 1024K 512K 1024K
Supply Voltage 3.3 V 3.3 V 3.3 V 3.3 V 3.3 V
Ethernet Data Rate 100 Mbps 100 Mbps 100 Mbps 100 Mbps 100 Mbps
Integrated PHY Count 2 2 2 2 2
Integrated MCU Core 32-bit Arm Cortex-M4F 32-bit Arm Cortex-M4F 32-bit Arm Cortex-M4F 32-bit Arm Cortex-M4F 32-bit Arm Cortex-M4F
Host Interface RMII and USB 2.0 RMII and USB 2.0 RMII and USB 2.0 RMII and USB 2.0 RMII and USB 2.0
Ethernet Standard IEEE 802.3 100BASE-TX IEEE 802.3 100BASE-TX IEEE 802.3 100BASE-TX IEEE 802.3 100BASE-TX IEEE 802.3 100BASE-TX
EtherCAT Configuration 2/3-port 2/3-port 2/3-port 2/3-port 2/3-port

Diferenciadores clave

  • Lower memory option within the same pin-compatible family (frente a LAN9255-V/ZMX020)
  • Integrated EtherCAT controller and Cortex-M4F reduce component count (frente a LAN9255-V/ZMX019)
  • Extended-industrial ordering option (frente a LAN9255-I/ZMX018)
  • More storage headroom is available without changing the footprint (frente a LAN9255-V/ZMX018)

Notas de diseño

Follow the LAN9255 Hardware Design Checklist for the 128-pin TQFP land pattern, including the exposed-pad connection and solder-mask definition. Use a multilayer PCB with a continuous ground reference, place local 3.3 V decoupling close to the supply pins, and verify that the assembly process develops a reliable exposed-pad solder fillet. Inspect both lead solder joints and exposed-pad wetting during first-article validation.

Route each 100BASE-TX differential pair as a controlled-impedance structure with closely matched length and geometry, continuous reference planes, and minimal stubs or test-point discontinuities. Keep the Ethernet PHY section physically separated from noisy switching and high-current paths. Review the completed layout against the manufacturer's hardware checklist and validate eye quality, link establishment, and error-free operation with the intended industrial cable.

Build the 3.3 V rail with low-impedance supply distribution and place the capacitance values required by the manufacturer close to the relevant device pins. Account for combined controller, microcontroller, and dual-PHY current when sizing the regulator and copper paths. Keep analog, digital, and I/O return currents controlled so that Ethernet transceiver performance is not degraded by shared high-di/dt loops.

The 128-pin TQFP uses an exposed pad for package-level heat spreading, but thermal performance still depends on the PCB copper area, stack-up, and enclosure airflow. Conduct a board-level thermal analysis using the final layout and worst-case operating conditions. Verify the exposed-pad soldering and temperature rise at the -40°C to +105°C rating limit before approving the assembly process.

Do not substitute a device solely because it uses a 128-pin TQFP; confirm that the EtherCAT controller, dual 100BASE-TX PHYs, Cortex-M4F functions, memory option, and exposed-pad footprint match the PCB. Moving from ZMX018 to ZMX019 or ZMX020 changes available memory but can affect linker usage and firmware planning. Validate the complete ordering code and thermal option before release.

Información de cumplimiento

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Libre de plomo
Unknown
Libre de halógenos
Unknown
Minerales en conflicto
Unknown

The listing identifies the part under EAR99 export classification and shows a REACH-status field, but no explicit compliance conclusion is present. Confirm RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations against current Microchip documentation.

Búsquedas relacionadas

lan9255 ethercat lan9255 i zmx020 lan9255 board microchip lan9255 LAN9255-V/ZMX018 datasheet LAN9255-V/ZMX018 datasheet pdf LAN9255-V/ZMX018 pinout LAN9255-V/ZMX018 equivalent LAN9255-V/ZMX018 replacement LAN9255-V/ZMX018 vs LAN9255-V/ZMX020 LAN9255-V/ZMX018 footprint LAN9255-V/ZMX018 price LAN9255-V/ZMX018 stock Microchip LAN9255 EtherCAT controller

Componentes & términos relacionados

Microchip Technology LAN9255-V/ZMX018 LAN9255-V/ZMX019 LAN9255-V/ZMX020 LAN9255-I/ZMX018 EtherCAT EtherCAT device controller EtherCAT slave controller Ethernet controller Arm Cortex-M4F SAM E53J 100BASE-TX IEEE 802.3 RMII USB 2.0 integrated Ethernet PHY industrial Ethernet factory automation industrial I/O motion control 128-pin TQFP exposed pad 3.3 V power supply programmable memory
RFQ de presupuesto rápido
Complete los detalles — nuestro equipo de ventas responderá en un plazo de 24 horas
Número de pieza Fabricante Encapsulado QTY Precio objetivo Total
✓
¡Presupuesto enviado!

Responderemos a su correo electrónico en un plazo de 24 horas

1
RFQ enviado
2
Presupuesto recibido
3
Pedido realizado
4
Pago
5
Enviado
6
Entregado
Ver detalles del RFQ