LM2902LVIDR - Quad 5.5V 1MHz Op Amp | Texas Instruments
N.º de pieza: LM2902LVIDR ✓ ActivoLM2902LVIDR Descripción general
An operational amplifier is an analog integrated circuit that uses high-gain differential amplification to improve signals applied to its two inputs. The LM2902LV belongs to the low-voltage operational-amplifier hierarchy, combining four amplifiers in one package. This integration reduces board area compared with four single-amplifier packages while providing a practical option for sensors, signal buffers, filters, and low-voltage control circuits.
The principal features of the LM2902LVIDR include four independent amplifier channels, a 1 MHz gain-bandwidth product, a 3 mV input offset-voltage specification, and operation from a nominal 2.7 V to 5.5 V supply range. Its low-voltage design is suitable for battery-powered and embedded systems where a 5 V or lower rail is available and higher-voltage legacy operational amplifiers would be unnecessary.
Each channel uses the standard operational-amplifier arrangement of an inverting input, a non-inverting input, an output, and a power connection. The device supports common signal-conditioning functions such as non-inverting and inverting gain stages, voltage followers, differential amplification, and active-filter sections. Because all four amplifiers share one package, engineers should evaluate supply routing, exposed input noise, output drive, and stability requirements for each individual channel.
Typical uses include low-voltage sensor interfaces, transducer buffering, analog signal conditioning, instrumentation, portable equipment, and industrial control modules. In a battery-powered design, the 5.5 V maximum operating supply helps avoid exposing the amplifier to an excessive rail voltage. In multi-channel signal acquisition, the four integrated channels can reduce component count while retaining independent operation for different analog signals.
Decoupling remains essential in a low-voltage amplifier design. Place the supply bypass capacitor close to the power pins and route the return path directly to the ground reference. Input and feedback components should be positioned to minimize parasitic capacitance and unwanted coupling between adjacent channels, especially when the 1 MHz bandwidth is used for higher-frequency signals.
This product page combines the manufacturer’s ordering information, exact device ratings, practical circuit guidance, and compatibility-focused alternatives. It is intended to help engineers select the correct voltage range, package, operating grade, and replacement before committing a LM2902LVIDR to a PCB or production BOM.
Alternativas directas para LM2902LVIDR — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
LM2902LVDG
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
LM2902LVDR
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
LM2902LVIDR Valores máximos y características eléctricas
| Number of Amplifier Channels | 4 channels |
| Amplifier Type | Standard general-purpose operational amplifier |
| Maximum Supply Voltage | 5.5 V |
| Supply Voltage Range | 2.7 V to 5.5 V |
| Nominal Single-Supply Operation | 5.5 V |
| Nominal Split-Supply Operation | ±2.75 V |
| Gain-Bandwidth Product | 1 MHz |
| Input Offset Voltage | 3 mV |
| Rango de temperatura de funcionamiento | -40°C to +125°C |
| Package Type | 14-pin SOIC (D) |
| Package Pin Count | 14 pins |
| Tipo de montaje | Surface mount |
| Product Family | LM290xLV low-voltage operational amplifiers |
| Supply Configuration | Single or split supply |
Guía de configuración de pines de LM2902LVIDR 14 pins
Configuración de pines para LM2902LVIDR (encapsulado 14 pins). Este componente analógico presenta pines de entrada, salida y alimentación. Consulte la hoja de datos del fabricante para conocer las configuraciones de los pines de ajuste de offset, compensación y habilitación. Ideal para circuitos de acondicionamiento de señal y amplificadores.
No hay datos detallados de patillaje disponibles para LM2902LVIDR.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
LM2902LVIDR es adecuado para 6 aplicacións: Low-Voltage Sensor Buffering, 5V Instrumentation Signal Conditioning, Battery-Powered Portable Equipment, Active Filter and Control Loops, Data Acquisition Front End, Industrial Interface Amplification.
Low-Voltage Sensor Buffering
The LM2902LVIDR is well suited to conditioning outputs from low-voltage sensors because each of its four channels can provide independent buffering or gain around a 2.7 V to 5.5 V supply. A 1 MHz gain-bandwidth product is appropriate for many temperature, pressure, and position sensors whose useful bandwidth is well below that limit. Designers should verify the sensor’s output range, common-mode behavior, and source impedance, then select resistor values that keep the amplifier within its input and output limits. Placing feedback resistors close to the relevant channel helps reduce parasitic effects and preserves predictable gain.
Recomendado
5V Instrumentation Signal Conditioning
The LM2902LVIDR can form the input-conditioning section of a 5 V instrumentation module, using its four channels for buffering, differential amplification, and active-filter stages. The 5.5 V maximum supply supports common laboratory and industrial interface voltages, while the 3 mV offset-voltage specification provides a defined starting point for precision evaluation. Actual error at the selected gain also depends on bias-current behavior, noise, resistor tolerance, and temperature. Engineers should compare the complete error budget against the sensor and converter rather than relying on offset voltage alone.
Recomendado
Battery-Powered Portable Equipment
The LM2902LVIDR fits portable equipment operating from a low-voltage battery-derived rail because the LM2902LV family supports 2.7 V to 5.5 V operation. Four channels reduce the package count when conditioning several analog controls or sensor outputs. The 1 MHz gain-bandwidth product is sufficient for human-interface controls, battery-status signals, and many low-bandwidth sensing paths. Designers should confirm whether the battery can exceed 5.5 V during transient events and include suitable rail protection when the source lacks controlled regulation.
Recomendado
Active Filter and Control Loops
Each LM2902LVIDR channel can implement a section of a low-frequency active filter or a feedback-control loop when powered from a 5 V or lower rail. Its 1 MHz gain-bandwidth product leaves bandwidth beyond many industrial process-control and audio-adjacent applications, while four channels allow a filter bank or multiple control blocks in one package. Component tolerances and the amplifier’s operating-point behavior should be evaluated together, particularly where phase margin and closed-loop stability depend on the selected feedback network.
Recomendado
Data Acquisition Front End
The LM2902LVIDR can serve as the analog front end of a low-voltage data-acquisition system when several input channels must be buffered before conversion. Its four independent amplifiers allow the design to use a consistent conditioning topology across sensor, reference, and diagnostic signals. The 1 MHz bandwidth should be compared with the acquisition rate and anti-alias filter requirements rather than treated as the system bandwidth by itself. Input-referenced noise, offset drift, settling behavior, and common-mode range must also be included in the converter error budget.
Recomendado
Industrial Interface Amplification
The LM2902LVIDR is suitable for general-purpose industrial interface amplification because it combines four channels, a 2.7 V to 5.5 V supply range, and a -40°C to +125°C operating specification. It can amplify low-level control or measurement signals when the application remains within the amplifier’s electrical limits. For new industrial designs, engineers should confirm exact load capability, output swing, input bias behavior, and noise performance from the manufacturer datasheet, then evaluate electromagnetic robustness at the board and enclosure level.
Recomendado
Datos de referencia de ingeniería para LM2902LVIDR — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | LM2902LVDG | LM2902LVDR |
|---|---|---|---|
| Package | 14-pin SOIC (D) | 14-pin SOIC (D) | 14-pin SOIC (D) |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Number of Channels | 4 | 4 | 4 |
| Maximum Supply Voltage | 5.5 V | 5.5 V | 5.5 V |
| Supply Voltage Range | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V |
| Gain-Bandwidth Product | 1 MHz | 1 MHz | 1 MHz |
| Input Offset Voltage | 3 mV | 3 mV | 3 mV |
| Operating Temperature Range | -40°C to +125°C | -40°C to +125°C | -40°C to +125°C |
| Nominal Split-Supply Operation | ±2.75 V | ±2.75 V | ±2.75 V |
| Amplifier Type | Standard general-purpose | Standard general-purpose | Standard general-purpose |
Diferenciadores clave
- Four channels in one low-voltage package (frente a LM2902LVDG)
- Direct fit for 2.7 V to 5.5 V systems (frente a LM2902LVDR)
- Documented wide temperature operation (frente a LM2902LVDG)
Notas de diseño
Place the LM2902LVIDR bypass capacitor immediately beside the device power pins and connect it to the ground reference with a short, low-inductance path. Keep each amplifier’s input and feedback components close to their assigned channel to limit parasitic capacitance. Route sensitive non-inverting inputs away from the output pins of adjacent amplifiers so that 1 MHz-class signals do not couple into high-impedance input nodes.
Design the LM2902LVIDR around a controlled 2.7 V to 5.5 V rail. If the source is a battery or an unregulated converter, verify its maximum transient voltage rather than relying only on the nominal voltage. Add the input capacitance and decoupling arrangement specified by the manufacturer, and account for startup and supply-transient behavior in the system power sequence.
Do not select the LM2902LV as a generic substitute for a 26 V or 36 V operational amplifier. The target device is limited to 5.5 V, and the ordinary LM2902 family has a substantially different supply rating. Also avoid treating the 3 mV offset-voltage figure as total error: bias current, input voltage, noise, resistor tolerance, temperature drift, and output-loading conditions can dominate a precision design.
Check the selected noise gain against the LM2902LVIDR’s 1 MHz gain-bandwidth product, and verify stability with the actual source impedance, load, and compensation network. Because four channels share one package, test adjacent channels for unwanted coupling during switching or high-gain operation. Long feedback loops and high-impedance nodes should be avoided because parasitic capacitance can alter phase margin and settling behavior.
Información de cumplimiento
The -40°C to +125°C operating range does not by itself establish AEC-Q100 qualification. Compliance fields remain unknown until the exact suffix and manufacturer declarations are confirmed.