LT1016CH - 10 ns Precision Comparator | Analog Devices
N.º de pieza: LT1016CH ✓ ActivoLT1016CH Descripción general
A comparator is an analog-to-digital interface integrated circuit that compares two input voltages and produces a logic-level result indicating their relative state. In the product hierarchy, the LT1016CH is a comparator within the broader amplifier and interface IC family. Unlike an operational amplifier, a comparator is optimized for rapid binary decisions rather than linear signal amplification. The LT1016CH combines this decision function with low propagation delay and compatibility with common TTL and CMOS logic families.
The primary feature of the LT1016CH is its 10 ns response time. This fast transition allows the comparator to resolve input differences with little delay, making it appropriate for pulse-width measurement, zero-cross detection, high-speed thresholding, and timing-reference circuits. The matched complementary outputs allow system designers to use true and inverted logic signals from one device. The manufacturer also specifies tight offset voltage and high gain, supporting precision comparison tasks where input offset can affect the decision point.
The LT1016CH can operate from dual ±5 V rails or a single 5 V supply. This operating flexibility is valuable in legacy instrumentation, laboratory equipment, industrial control systems, and mixed-signal designs where negative input or output signal ranges may be required. Its negative-supply quiescent current is specified as 3 mA, and performance is not affected by variations in negative supply voltage. These characteristics simplify power planning in systems where the negative rail is generated from another supply through a resistive divider.
Typical uses include high-speed edge detection, pulse-width monitoring, window comparison, oscillator timing, overvoltage detection, and threshold circuits feeding TTL or CMOS logic. The complementary outputs can reduce the need for an additional inverter, while the 10 ns delay supports higher event rates than general-purpose comparators. Care should still be taken to control input overdrive, ringing, output loading, and supply bypassing near the device.
For reliable operation, place input and supply bypass capacitors close to the corresponding pins and route high-speed comparator signals over short, controlled-impedance traces. Avoid long unprotected routes between the comparator and receiving logic, and evaluate output behavior with the actual load and supply arrangement. Use the manufacturer pin description and connection diagrams when assigning PCB functions and latch-control logic.
This page organizes the LT1016CH specifications, sourcing information, application guidance, and verified drop-in assessment into a practical engineering reference. It also highlights design constraints that matter beyond the headline 10 ns speed, including supply architecture, complementary-output use, latch control, and high-speed PCB implementation.
Alternativas directas para LT1016CH — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
No hay alternativas directas disponibles para este producto.
Solicitar alternativasLT1016CH Valores máximos y características eléctricas
| Comparator Type | Ultra-fast precision comparator |
| Propagation Delay | 10 ns |
| Positive Supply Voltage | 5 V |
| Supply Configuration | ±5 V or single 5 V |
| Logic Interface | Direct TTL/CMOS |
| Tipo de salida | Matched complementary outputs |
| Quiescent Negative Supply Current | 3 mA |
| Negative Supply Sensitivity | Performance is not affected by variations in negative supply voltage |
| Latch Function | Available |
| Encapsulado | 10-pin TO-5 |
| Output Drive | Active drive in both directions |
Guía de configuración de pines de LT1016CH 10-pin to-5
Configuración de pines para LT1016CH (encapsulado 10-pin to-5). Este componente analógico presenta pines de entrada, salida y alimentación. Consulte la hoja de datos del fabricante para conocer las configuraciones de los pines de ajuste de offset, compensación y habilitación. Ideal para circuitos de acondicionamiento de señal y amplificadores.
No hay datos detallados de patillaje disponibles para LT1016CH.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
LT1016CH es adecuado para 6 aplicacións: High-Speed Pulse-Width Detection, Zero-Cross and Edge Detection, Precision Threshold Monitoring, High-Speed Window Comparator, Oscillator and Timing Reference, Test and Measurement Trigger Circuit.
High-Speed Pulse-Width Detection
The LT1016CH is suitable for detecting the duration of narrow pulses because its 10 ns propagation delay limits the timing uncertainty added by the comparison stage. Direct TTL/CMOS interfacing allows the result to enter counters, flip-flops, or timing logic without a separate output-driver stage. Matched complementary outputs provide true and inverted decisions for different downstream logic conventions. When using the comparator near the bandwidth limit, minimize propagation distance, control input overdrive, and keep the input traces short to limit ringing and crosstalk.
Recomendado
Zero-Cross and Edge Detection
The LT1016CH can convert rapid analog crossings into digital edge events with a 10 ns nominal propagation delay. Its high gain and tight offset-voltage specifications support precise decisions around a selected reference voltage, while the active output stage drives logic in both directions. This makes the device applicable to waveform timing, frequency events, and synchronized pulse detection. The input network should preserve the intended crossing point, and supply bypassing should be placed close to the comparator to prevent local supply disturbance from affecting the decision.
Recomendado
Precision Threshold Monitoring
The LT1016CH supports precision threshold monitoring by comparing a changing input against a reference and producing a fast complementary logic decision. Tight offset-voltage specifications and high gain help reduce ambiguity near the threshold, while the 10 ns response can be valuable when the monitored quantity changes rapidly. The LT1016CH may be used for overvoltage indication, signal-limit detection, or alarm generation. Reference accuracy, input noise, and propagation delay determine the practical detection margin, so those parameters should be evaluated together rather than independently.
Recomendado
High-Speed Window Comparator
Two LT1016CH devices can form the basis of a fast window comparator, with one device detecting the lower threshold and another detecting the upper threshold. Their 10 ns propagation delay helps preserve timing relationships between the complementary decisions, while matched outputs make it convenient to combine the results in digital logic. The design must account for input-referred offset, channel-to-channel comparison behavior, and propagation-delay matching if precise transition timing is required. Keep both channels electrically similar and provide local supply decoupling.
Recomendado
Oscillator and Timing Reference
The LT1016CH can provide a rapid threshold decision in oscillator, pulse-generation, and timing-reference circuits where a delayed output would alter the intended oscillation period. The direct TTL/CMOS interface enables the comparator to drive subsequent digital timing stages, while complementary outputs can simplify inversion or edge-polarity control. Component tolerances, saturation recovery, and propagation delay will influence cycle accuracy, so the circuit should be simulated across supply and temperature limits. Short feedback paths and clean grounding are especially important in high-speed timing loops.
Recomendado
Test and Measurement Trigger Circuit
The LT1016CH is useful in test and measurement equipment that must convert an analog waveform crossing into a deterministic trigger event. A 10 ns propagation delay reduces timing uncertainty, and the matched complementary outputs can trigger capture logic with either polarity. The LT1016CH also supports ±5 V operation, making it suitable for instrumentation that develops bipolar signals or requires a single-ended 5 V implementation. Probe loading, source impedance, and input overdrive must be controlled because these factors can shift the effective threshold and alter triggering reliability.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para LT1016CH — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto |
|---|---|
| Brand | Analog Devices |
| Package | 10-pin TO-5 |
| Product Type | Ultra-fast precision comparator |
| Propagation Delay | 10 ns |
| Supply Configuration | ±5 V or single 5 V |
| Logic Interface | Direct TTL/CMOS |
| Output Configuration | Matched complementary outputs |
| Latch Function | Yes |
| Negative-Supply Quiescent Current | 3 mA |
Diferenciadores clave
- Fast propagation delay (frente a General-purpose precision comparators)
- Dual-or-single supply operation (frente a Single-supply-only comparators)
- Direct complementary logic drive (frente a Comparators requiring external inversion or output drivers)
- Retained decision capability (frente a Comparators without a latch function)
Notas de diseño
Place input, output, and bypass connections close to the LT1016CH to limit parasitic feedback and ringing. The 10 ns propagation delay is short enough that long PCB traces can introduce noticeable timing differences. Use a compact ground reference, avoid routing the input beside high-current switching nodes, and maintain a continuous ground path beneath the signal route. For repeatable high-speed results, test the assembled board with a low-capacitance probe rather than relying only on simulation.
Bypass each supply connection with the capacitance and ESR range specified in the manufacturer application guidance, and place the bypass network immediately adjacent to the device pins. The LT1016CH can use ±5 V or single 5 V operation, so verify signal ranges before finalizing the negative-supply arrangement. If the negative rail is generated through a divider, account for the divider impedance and the 3 mA negative-supply quiescent current when checking rail stability.
Do not assume that every LT1016 family order code is a drop-in replacement for LT1016CH. The CH device uses a 10-pin TO-5 configuration, while the CJ8, CN8, and CS8 variants have different package suffixes. A replacement must match the footprint, pin functions, supply range, propagation delay, output behavior, and latch requirements. Also observe input common-mode limits and output loading; operation outside these boundaries can cause incorrect decisions even when the logic interface appears functional.
Información de cumplimiento
No definitive environmental or automotive qualification statements were identified for the exact LT1016CH ordering configuration.
