Analog Devices

LT1101CJ8 - Precision Micropower Instrumentation Amplifier | ADI

N.º de pieza: LT1101CJ8 ✓ Activo
5 V Vdss 6 nA Id 8-lead CERDIP, 0.300 in (7.62 mm) pitch Package
MOQ: 1 |

LT1101CJ8 Descripción general

The Analog Devices LT1101CJ8 is a precision, micropower, single-supply instrumentation amplifier with fixed gain options of 10 or 100, supplied in an 8-lead CERDIP package. It supports operation from a single 5V supply as well as dual ±15V supplies, making it suitable for low-power sensor measurement and signal-conditioning circuits. Key characteristics include 82 dB gain, 6 nA input bias current, a 2.2V to 36V total supply range, and low-power operation from one lithium cell or two Ni-Cad batteries.

An instrumentation amplifier is a specialized amplifier category designed to amplify small differential signals while rejecting common-mode interference. Its internal topology typically combines an input stage, differential gain stage, and output stage to provide high input impedance, accurate differential gain, and common-mode rejection. The LT1101 extends this hierarchy from instrumentation amplifier to precision analog amplifier, analog signal conditioner, and low-power power-management-aware IC for battery-powered measurement equipment.

The fixed-gain architecture eliminates the need for an external gain-setting resistor, which can reduce component count and remove resistor-ratio tolerance from the gain equation. Available fixed gains of 10 and 100 support bridge-sensor, pressure-transducer, and low-level differential-input applications. Its 6 nA input bias current is particularly useful when the source impedance is high, because lower bias current reduces the voltage error generated across the source impedance.

The LT1101 is optimized for precision and micropower operation rather than high-bandwidth signal capture. Its 82 dB gain provides approximately 126-fold voltage amplification in the applicable gain configuration, while the single-supply capability simplifies systems that cannot accommodate negative rails. A single lithium cell or two Ni-Cad batteries can power the device, enabling portable measurement systems that must balance signal accuracy against energy consumption.

Typical uses include battery-powered strain-gauge and bridge amplifiers, industrial pressure and force measurement, low-current sensor interfaces, portable diagnostic instruments, and precision analog data-acquisition systems. In these applications, the fixed gain reduces calibration variability, while the low bias current helps preserve weak sensor signals. Designers should still verify source-impedance limits, input common-mode range, supply headroom, and settling requirements for the intended gain configuration.

For a single 5V design, place the input and output bypass capacitors close to their associated pins and maintain a quiet ground return around the signal path. Because instrumentation-amplifier accuracy depends on differential excitation and common-mode rejection, unequal input impedances and asymmetrical routing should be avoided. Review the manufacturer pin-description table and recommended application circuit before assigning PCB nets or selecting the fixed-gain version.

This page consolidates manufacturer specifications, verified source links, drop-in family options, comparison parameters, and practical circuit-placement guidance for engineers evaluating the LT1101CJ8. It also distinguishes documented electrical characteristics from unresolved package, lifecycle, temperature-grade, and pricing details so design decisions can be validated before production release.

Alternativas directas para LT1101CJ8 — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.

LT1101CS8

✅ Sustitución directa ⚠️ Especificaciones sin verificar
📦 8-lead CERDIP
Same LT1101 fixed-gain architecture and 8-lead package; temperature-grade ordering differs, while the documented core gain and supply specifications remain unchanged at 82 dB and 2.2V to 36V

📋 Alternativa de referencia (no en el catálogo)

LT1101CZ8

✅ Sustitución directa ⚠️ Especificaciones sin verificar
📦 8-lead CERDIP
Same LT1101 fixed-gain architecture and 8-lead package; temperature-grade ordering differs, while the documented core gain and supply specifications remain unchanged at 82 dB and 2.2V to 36V

📋 Alternativa de referencia (no en el catálogo)

LT1101CN8

✅ Sustitución directa ⚠️ Especificaciones sin verificar
📦 8-lead CERDIP
Same LT1101 fixed-gain architecture with an 8-lead through-hole footprint; package material and temperature-grade ordering differ, while core gain and supply ratings remain unchanged at 82 dB and 2.2V to 36V

📋 Alternativa de referencia (no en el catálogo)

LT1101CJ8 Valores máximos y características eléctricas

Product Type Precision micropower single-supply instrumentation amplifier
Fixed Gain Options 10 or 100 V/V
Gain 82 dB
Input Bias Current 6 nA
Single-Supply Operation 5 V
Dual-Supply Operation ±15 V
Total Supply Range 2.2 V to 36 V
Total Supply Range, Dual-Supply Configuration ±1.1 V to ±18 V
Number of Circuits 1 circuit
Encapsulado 8-lead CERDIP, 0.300 in (7.62 mm) pitch
Terminal Count 8 terminals
Terminal Form Through-hole
Temperature Grade Commercial
External Gain-Setting Resistor Not required
Battery Compatibility 1 lithium cell or 2 Ni-Cad batteries

Guía de configuración de pines de LT1101CJ8 8-lead cerdip, 0.300 in (7.62 mm) pitch

Configuración de pines para LT1101CJ8 (encapsulado 8-lead cerdip, 0.300 in (7.62 mm) pitch). Este componente analógico presenta pines de entrada, salida y alimentación. Consulte la hoja de datos del fabricante para conocer las configuraciones de los pines de ajuste de offset, compensación y habilitación. Ideal para circuitos de acondicionamiento de señal y amplificadores.

Diagrama de patillaje del encapsulado 8-lead cerdip, 0.300 in (7.62 mm) pitch para LT1101CJ8

No hay datos detallados de patillaje disponibles para LT1101CJ8.

Consulte la hoja de datos para ver la configuración completa de patillas.

Aplicaciones típicas

LT1101CJ8 es adecuado para 6 aplicacións: Battery-Powered Bridge Sensor Amplifier, Industrial Pressure Transducer Interface, Low-Current Sensor Signal Conditioning, Portable Diagnostic Instrument, Precision Analog Data Acquisition, Two-Battery Industrial Monitoring.

📱

Battery-Powered Bridge Sensor Amplifier

The LT1101CJ8 fits low-level differential measurements from resistive bridges because it offers fixed gains of 10 or 100, 82 dB gain, and only 6 nA input bias current. The low bias current limits the input-generated error when strain-gauge or resistive-sensor impedances are high. Place the sensor return at the amplifier reference connection and preserve symmetry between the two input paths. Operation from one lithium cell is possible, but the available voltage must remain above the required supply and common-mode limits. The absence of an external gain-setting resistor also reduces board area and removes resistor-ratio variation from the gain calibration.

🏭

Industrial Pressure Transducer Interface

The LT1101CJ8 is suitable for precision pressure and force transducers that produce a differential output around a common-mode voltage. Its 10 or 100 fixed-gain options provide enough attenuation control without external gain resistors, while the 6 nA input bias current supports relatively high source resistance. In an industrial controller, the amplifier can sit close to the sensor connector to prevent noise pickup before the small differential signal is amplified. The 2.2V to 36V total supply range allows use with 5V and higher-rail systems, although the input common-mode range must be checked at every input level.

🧩

Low-Current Sensor Signal Conditioning

The LT1101CJ8 can condition weak differential signals from high-impedance sensors where input-bias-current error would otherwise reduce measurement accuracy. Its 6 nA bias current is particularly helpful with leakage-sensitive sensing arrangements, and the fixed 10 or 100 gain makes the device convenient for standardized sensor channels. The micropower architecture supports portable test equipment and reduces the load imposed on battery-powered systems. Designers should route both inputs symmetrically, use a quiet reference node, and verify that sensor output remains inside the amplifier's valid input common-mode range at the minimum supply voltage.

💊

Portable Diagnostic Instrument

The LT1101CJ8 supports compact diagnostic and measurement instruments that need differential gain without a complex adjustable-gain network. Fixed gains of 10 and 100 allow the instrument to cover two standardized sensitivity ranges, while single 5V operation simplifies power architecture around battery-powered probes. The 82 dB gain amplifies small differential excitations while the 6 nA input bias current minimizes disturbance to high-impedance sources. For reliable readings, isolate the analog path from switching converters, decouple the supply at the device, and ensure the output remains within its operating range under the highest sensor excitation.

🖥️

Precision Analog Data Acquisition

The LT1101CJ8 can serve as the first analog stage in a precision data-acquisition channel when the source is differential and the required gain is known. The 10 or 100 fixed-gain options simplify system calibration and reduce component count compared with an externally programmed instrumentation amplifier. Its single-circuit implementation and 8-lead CERDIP package also fit compact analog boards with through-hole assembly requirements. For multiplexed systems, allow sufficient settling time between channel changes, keep the reference and ground connections quiet, and verify that source resistance remains compatible with the 6 nA input bias-current specification.

⚡

Two-Battery Industrial Monitoring

The LT1101CJ8 can operate from two Ni-Cad batteries, making it applicable to portable industrial monitoring equipment that does not use a regulated 5V rail. Its 82 dB gain and fixed-gain options support small differential sensor outputs, while the low 6 nA input bias current helps preserve accuracy with resistive sensing elements. As the battery voltage changes, designers should use the manufacturer supply and common-mode limits to determine the usable measurement range. Stable reference grounding and short input traces are important because poor return paths can reduce effective common-mode rejection even when the nominal gain remains unchanged.

What is the LT1101CJ8?
The LT1101CJ8 is a precision, micropower, single-supply instrumentation amplifier with fixed gain options of 10 or 100 in an 8-lead CERDIP package. According to the Analog Devices product page, it combines single 5V operation with dual ±15V capability, requires no external gain-setting resistor, and can operate from one lithium cell or two Ni-Cad batteries.
What is the supply voltage range of LT1101CJ8?
The LT1101CJ8 operates from 2.2V to 36V across its total supply range and supports ±1.1V to ±18V dual supplies. The manufacturer also identifies 5V single-supply and ±15V dual-supply operating conditions, allowing the same device family to serve portable, industrial, and laboratory measurement systems.
What is the gain of LT1101CJ8?
The LT1101CJ8 provides 82 dB gain and is offered in fixed-gain versions of 10 or 100 V/V. According to the Analog Devices product information, the fixed-gain architecture eliminates the external gain-setting resistor, which simplifies the circuit and prevents external resistor tolerance from directly changing the programmed gain.
Why is the 6 nA input bias current of LT1101CJ8 important?
The 6 nA input bias current reduces the input-offset error generated when the LT1101CJ8 is connected to a high-impedance source. The error contribution is approximately the bias current multiplied by source impedance, so low bias current is particularly valuable for strain gauges, resistive bridges, potentiometers, and other sensors that can present substantial source resistance.
Can LT1101CJ8 operate from a single lithium cell?
Yes. The Analog Devices product page specifically identifies single-lithium-cell operation, and the LT1101CJ8 also supports a single 5V supply. This makes it appropriate for portable instruments where the number of cells, quiescent demand, and usable measurement range must be balanced; input and output headroom should still be checked at the lowest cell voltage.
Where can I download the LT1101CJ8 datasheet PDF?
The official LT1101 datasheet and product information are available from Analog Devices at https://www.analog.com/en/products/lt1101.html. The LT1101CJ8 is the commercial-temperature, 8-lead CERDIP ordering option. Use the manufacturer datasheet for the complete pin-description table, absolute-maximum ratings, recommended application circuit, and ordering information.
Where can I find the LT1101CJ8 pinout?
The LT1101CJ8 pinout is documented in the manufacturer LT1101 datasheet associated with the official Analog Devices product page. The device uses an 8-lead CERDIP package, but the individual terminal names and recommended connections are not reproduced on this page. Use the datasheet pin-description table when assigning PCB tracks or checking the fixed-gain configuration.
What are the best drop-in replacements for LT1101CJ8?
The closest documented drop-in family options are the other 8-lead LT1101 ordering variants that retain the same instrumentation-amplifier architecture and package format. Because gain selection, temperature grade, and ordering suffixes can change the functional requirements, each candidate must be checked against the required 10 or 100 gain before release. Cross-brand alternatives are not listed without a verified pin-to-pin cross reference.
What can replace LT1101CJ8 without redesigning the PCB?
A PCB-compatible replacement should use the same 8-lead CERDIP footprint and provide the required fixed gain of either 10 or 100 V/V within the LT1101CJ8 supply limits. The verified cross-reference information identifies LT1101-family replacements, but it does not establish enough detail for a cross-brand substitute. Confirm the complete ordering code, gain option, temperature grade, and pin assignments before substitution.
When should I choose LT1101CJ8 over a general-purpose op amp?
Choose the LT1101CJ8 when the input is a small differential signal, the source impedance may be high, and common-mode rejection is important. Its 6 nA input bias current, 82 dB gain, and fixed 10 or 100 gain options simplify precision bridge amplification. A general-purpose op amp may be appropriate when only single-ended amplification is needed and the added instrumentation-amplifier features are unnecessary.
Is LT1101CJ8 suitable for battery-powered sensor measurement?
Yes. The LT1101CJ8 is specifically designed for micropower operation and can operate from one lithium cell or two Ni-Cad batteries. Its fixed-gain architecture reduces external components, while the 6 nA input bias current limits error with high-impedance sensors. The complete power budget should also include sensor current, external resistors, and the required output-signal settling behavior.
How much supply current does LT1101CJ8 use?
The LT1101CJ8 is a micropower instrumentation amplifier, but a definitive numerical supply-current value is not established on this product page. Use the manufacturer datasheet for the operating-current maximum and typical curves at each supported supply voltage. Compare that value with the sensor and downstream circuit requirements when sizing a battery.
Where can I buy LT1101CJ8 and check its lead time?
Use the Request a Quote form on this page to ask about LT1101CJ8 availability, current lead time, and order handling. The form is the appropriate channel for a quote and current scheduling because catalog status and lead time can change without notice. The component is identified as an 8-lead, through-hole CERDIP device suitable for conventional PCB assembly.
What is the price of LT1101CJ8?
The current LT1101CJ8 unit price is not published as a static figure on this page. Submit the part number through the Request a Quote form to obtain a current quote and quantity-break availability for the exact 8-lead CERDIP ordering code. This avoids presenting an outdated catalog price as a current purchasing commitment.
Is LT1101CJ8 in stock?
Current stock for LT1101CJ8 should be confirmed through the Request a Quote form on this page because distributor inventory can change rapidly. When requesting a quote, identify the required quantity, LT1101CJ8 ordering code, and whether the 8-lead CERDIP package and commercial temperature grade are mandatory for the assembly.
LT1101CJ8 vs an LT1101 family replacement — which is better?
The best choice is the family member that preserves the required gain, supply range, 8-lead CERDIP footprint, and temperature grade. The LT1101CJ8 is the commercial-grade ordering option, while other LT1101 suffixes can represent different grade or screening combinations. Do not substitute based only on the base family name; compare the complete ordering table and pin configuration in the manufacturer datasheet.
What is the best cross-brand equivalent for LT1101CJ8?
No cross-brand equivalent is claimed because the available cross-reference material does not establish a verified pin-to-pin, same-package substitute with comparable fixed gain and supply limits. An engineer should compare the exact 8-lead pinout, gain of 10 or 100, input bias current, common-mode range, supply range, and noise before approving another manufacturer’s device. This prevents a merely similar instrumentation amplifier from being treated as a drop-in replacement.

Datos de referencia de ingeniería para LT1101CJ8 — comparación, orientación de diseño e información de cumplimiento.

Guía de selección

Choose the LT1101CJ8 for compact, low-power differential measurements where a fixed gain of 10 or 100, low input bias current, and single-supply operation are important. It is particularly suitable for high-impedance bridge sensors, portable instruments, and 5V industrial systems. LT1101CS8 or LT1101CZ8 may be preferable when the required temperature grade or screening combination differs, but each complete ordering code must be checked against the gain and environmental requirements. LT1101CN8 belongs to the same family and pin-compatible format, with package-material and grade considerations controlling its use. Do not select a different instrumentation amplifier solely by input count or nominal gain: verify the full 8-pin assignment, common-mode range, output swing, supply limits, bias current, noise, and settling behavior. Cross-brand substitutes should be used only after their manufacturer confirms both mechanical compatibility and electrical equivalence.

Comparación con alternativas

Parámetro Este producto LT1101CS8 LT1101CZ8 LT1101CN8
Package 8-lead CERDIP, through-hole 8-lead CERDIP 8-lead CERDIP 8-lead CERDIP
Brand Analog Devices Analog Devices Analog Devices Analog Devices
Product Type Precision micropower instrumentation amplifier Instrumentation amplifier Instrumentation amplifier Instrumentation amplifier
Gain 82 dB 82 dB 82 dB 82 dB
Fixed Gain Options 10 or 100 V/V 10 or 100 V/V 10 or 100 V/V 10 or 100 V/V
Input Bias Current 6 nA 6 nA 6 nA 6 nA
Total Supply Range 2.2V to 36V 2.2V to 36V 2.2V to 36V 2.2V to 36V
Single-Supply Operation 5 V 5 V 5 V 5 V
Dual-Supply Operation ±15 V ±15 V ±15 V ±15 V
External Gain-Setting Resistor Not required Not required Not required Not required

Diferenciadores clave

  • Fixed-gain architecture removes the external gain-setting resistor (frente a LT1101CS8)
  • Low input bias current supports high-impedance sensing (frente a LT1101CZ8)
  • Wide supply flexibility supports portable and industrial rails (frente a LT1101CN8)

Notas de diseño

Route the two differential inputs as a symmetrical pair and minimize their distance to the LT1101CJ8. Avoid sharing a long return path between the inputs, because unequal trace resistance and parasitic coupling can degrade common-mode rejection. Place the input-referenced bypass capacitor close to the supply pin, maintain a continuous ground plane, and connect the sensor or source ground to the amplifier reference using the shortest practical route.

Verify the supply and input common-mode limits at the minimum battery or rail voltage, not only at the nominal operating point. The LT1101CJ8 supports single 5V and dual ±15V operation and has a documented total supply range of 2.2V to 36V. For battery systems, include the sensor load, divider current, and quiescent demand in the cell-capacity calculation, and confirm that the output remains within its valid range at maximum signal excursion.

Keep high-impedance sensor connections short and protect them from moisture, leakage, and nearby switching nodes. The documented 6 nA input bias current is beneficial for high-source-impedance sensing, but PCB contamination can introduce leakage of comparable or greater magnitude. Use a clean guard or driven guard technique where appropriate and compare measured input bias current with the estimated error, calculated as source impedance multiplied by total input leakage.

Do not select a family member solely by the LT1101 base designation. Confirm the complete ordering code, required fixed gain of 10 or 100 V/V, package, and temperature grade in the manufacturer ordering table. The alternatives listed here retain the 8-lead family format, but suffix changes can represent different grade or screening combinations. Confirm the pin-description table and recommended application circuit before substituting any ordering code.

Información de cumplimiento

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Libre de plomo
Unknown
Libre de halógenos
Unknown
Minerales en conflicto
Unknown

No explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations were identified for this exact ordering code in the cited sources. Use the current manufacturer product declaration and material-compliance documents before release.

Datos verificados el: 2026-11-14 — datos verificados y seleccionados por el equipo de ingeniería de componentes de XAIPART

Búsquedas relacionadas

LT1101CJ8 datasheet LT1101CJ8 datasheet pdf LT1101CJ8 pinout LT1101CJ8 equivalent LT1101CJ8 replacement LT1101CJ8 cross reference LT1101CJ8 8-CERDIP LT1101CJ8 82 dB gain LT1101CJ8 6 nA input bias LT1101CJ8 single supply LT1101CJ8 battery sensor amplifier LT1101CJ8 vs LT1101CS8 LT1101CJ8 price LT1101CJ8 stock Analog Devices LT1101CJ8

Componentes & términos relacionados

Analog Devices Linear Technology LT1101CJ8 LT1101CS8 LT1101CZ8 LT1101CN8 instrumentation amplifier precision amplifier analog signal conditioner semiconductor fixed-gain amplifier differential amplifier common-mode rejection input bias current 82 dB gain 6 nA input bias current single-supply operation dual-supply operation 5 V single supply ±15 V dual supply 2.2 V to 36 V supply range 8-lead CERDIP DIP package through-hole package bridge sensor pressure transducer battery-powered measurement RoHS REACH
RFQ de presupuesto rápido
Complete los detalles — nuestro equipo de ventas responderá en un plazo de 24 horas
Número de pieza Fabricante Encapsulado QTY Precio objetivo Total
✓
¡Presupuesto enviado!

Responderemos a su correo electrónico en un plazo de 24 horas

1
RFQ enviado
2
Presupuesto recibido
3
Pedido realizado
4
Pago
5
Enviado
6
Entregado
Ver detalles del RFQ