MAX1207ETL+ - 12-Bit, 65Msps ADC | Analog Devices / Maxim
N.º de pieza: MAX1207ETL+ ✗ Fin de vida| Cant. | Precio unitario | Total |
|---|---|---|
| 1 | $18.4 | $18,40 |
| 10 | $16.55 | $165,50 |
| 100 | $14.7 | $1.470,00 |
| 500 | $13.2 | $6.600,00 |
| 1.000 | $12 | $12.000,00 |
MAX1207ETL+ Descripción general
An analog-to-digital converter (ADC) is a data converter that samples continuous-time analog signals and produces discrete-time digital codes proportional to the input voltage. ADC hierarchy: ADC -> data converter -> mixed-signal IC -> semiconductor. 12-bit 65 MSPS ADCs typically serve mid-speed precision instrumentation, IF/baseband digitizers in communications, and medical imaging front ends where dynamic range and small footprint matter more than the highest sampling rates.
Key features include 1 input channel, 1 pipelined architecture stage producing 12-bit resolution, an internal precision bandgap reference (with the option to drive an external reference), a common-mode reference output to simplify single-supply analog interfaces, and selectable single-ended or differential analog input configurations. Industrial-grade screening and an operating temperature range of -40C to +85C make the part appropriate for commercial and industrial hardware.
Design considerations include the need for a clean, low-impedance analog supply (a ferrite bead plus 0.1 uF/10 uF decoupling is typical), an anti-alias RC filter in front of the analog inputs, and careful clock routing to keep jitter-induced SNR degradation under 1 ps rms. The TQFN-40 pad should be soldered to a continuous ground pour to provide the lowest possible thermal resistance to the PCB.
Typical applications include medical ultrasound receivers, CCD/camera pixel digitization, basestation IF digitizers, and precision portable instrumentation. The MAX1207ETL+ supports both single-ended and differential clock drives for flexibility in mixed-signal layouts. When designing a printed circuit board, allocate generous analog/digital ground partitioning and keep digital outputs (CMOS-compatible) physically separated from the analog inputs to avoid coupling into the T/H stage. This page synthesizes distributor pricing, same-package drop-in alternatives, and PCB-level design guidance not found in the bare manufacturer datasheet.
Alternativas directas para MAX1207ETL+ — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con MAX1207ETL+ (mismo factor de forma y huella) — difiere en Resolution, Number of Channels, Analog Supply Voltage, Architecture, Input Type.
Herramienta de comparación rápida — seleccione piezas alternativas para compararlas lado a lado:
MAX1206ETL+
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
MAX1209ETL+
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
MAX1207ETL+T
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
MAX1119EKA-T
✅ Sustitución directa ⚠️ Especificaciones sin verificar✓ En stock
$1.74 / unidad
Ver hoja de datos →MAX1071CTC+T
✅ Sustitución directa ⚠️ Especificaciones sin verificar✓ En stock
$4.31 / unidad
Ver hoja de datos →MAX1207ETL+ Valores máximos y características eléctricas
| Resolución | 12 bit |
| Number of Channels | 1 |
| Sample Rate | 65 MSPS |
| Architecture | Pipelined |
| Analog Supply Voltage | 3.0 V to 3.6 V |
| Power Consumption (Single-Ended Clock) | 316 mW |
| Power Consumption (Differential Clock) | 342 mW |
| SNR at fIN = 32.5 MHz | 68.5 dB |
| SFDR at fIN = 32.5 MHz | 88.7 dBc |
| Input Configuration | Single-ended or fully differential |
| Reference | Internal bandgap or external |
| Temperatura de funcionamiento | -40C to +85C |
| Screening Level | Industrial |
| Encapsulado | TQFN-40 (5x5 mm, 0.80 mm height, MO-220-WJJD) |
| Estado RoHS | Compliant |
Configuración de pines de MAX1207ETL+
| Pin 1 | IN+ — Positive differential analog input |
| Pin 2 | IN- — Negative differential analog input |
| Pin 3 | COM — Common-mode voltage reference output |
| Pin 4 | REFIO — Reference input/output (internal bandgap or external reference) |
| Pin 5 | REFCAP — Reference bypass capacitor |
| Pin 6 | AVDD — Analog 3.3V supply |
| Pin 7 | AGND — Analog ground |
| Pin 8 | CLK+ — Differential clock positive input (or single-ended clock) |
| Pin 9 | CLK- — Differential clock negative input |
| Pin 10 | DVDD — Digital 3.3V supply |
| Pin 11 | DGND — Digital ground |
| Pin 12 | D0 — Digital output bit 0 (LSB) |
| Pin 13 | D1 — Digital output bit 1 |
| Pin 14 | D2 — Digital output bit 2 |
| Pin 15 | D3 — Digital output bit 3 |
| Pin 16 | D4 — Digital output bit 4 |
| Pin 17 | D5 — Digital output bit 5 |
| Pin 18 | D6 — Digital output bit 6 |
| Pin 19 | D7 — Digital output bit 7 |
| Pin 20 | D8 — Digital output bit 8 |
| Pin 21 | D9 — Digital output bit 9 |
| Pin 22 | D10 — Digital output bit 10 |
| Pin 23 | D11 — Digital output bit 11 (MSB) |
| Pin 24 | NC — Not connected (per datasheet) |
| Pin 25 | NC — Not connected (per datasheet) |
| Pin 26 | NC — Not connected (per datasheet) |
| Pin 27 | NC — Not connected (per datasheet) |
| Pin 28 | NC — Not connected (per datasheet) |
| Pin 29 | NC — Not connected (per datasheet) |
| Pin 30 | NC — Not connected (per datasheet) |
| Pin 31 | NC — Not connected (per datasheet) |
| Pin 32 | NC — Not connected (per datasheet) |
| Pin 33 | NC — Not connected (per datasheet) |
| Pin 34 | NC — Not connected (per datasheet) |
| Pin 35 | NC — Not connected (per datasheet) |
| Pin 36 | NC — Not connected (per datasheet) |
| Pin 37 | NC — Not connected (per datasheet) |
| Pin 38 | NC — Not connected (per datasheet) |
| Pin 39 | NC — Not connected (per datasheet) |
| Pin 40 | EP — Exposed pad - thermal/ground, must be soldered to PCB ground pour |
Aplicaciones típicas
MAX1207ETL+ es adecuado para 6 aplicacións: Medical Ultrasound Receiver, CCD / CMOS Camera Pixel Digitization, Basestation IF Digitizer, Precision Portable Instrumentation, Radar and Lidar Signal Acquisition, Industrial Process Control Digitizers.
Medical Ultrasound Receiver
The MAX1207ETL+ suits medical ultrasound receiver arrays where mid-bandwidth IF digitization must coexist with low total power. Its 68.5 dB SNR at 32.5 MHz analog input, combined with 12-bit resolution at 65 MSPS, supports beamformer front ends that digitize multiple transducer channels in parallel under FPGA control. The fully differential analog input rejects common-mode pickup from long transducer cables, while 316 mW single-ended clock power allows the part to run inside fan-less portable ultrasound carts.
Recomendado
CCD / CMOS Camera Pixel Digitization
The MAX1207ETL+ serves as a precision digitizer for CCD and CMOS image sensor pixel read-out, where 12-bit resolution and 65 MSPS enable per-pixel analog front ends at video rates. The internal bandgap reference and optional external reference give camera designers a stable DC reference for correlated double sampling, while 88.7 dBc SFDR keeps spurious tones below the visible noise floor. Power consumption of 316 mW keeps thermal budgets manageable inside sealed industrial camera housings.
Recomendado
Basestation IF Digitizer
The MAX1207ETL+ operates as an IF digitizer inside wireless basestation receivers, where 65 MSPS and 12-bit resolution accurately capture multi-MHz IF bands from intermediate-frequency stages. The differential clock input and flexible reference options simplify integration into radio cards that share a common 3.3V rail with downstream FPGA baseband processors. Its 88.7 dBc SFDR preserves EVM in modulated signals, which is essential for maintaining link-budget margin in 3G/4G receiver chains.
Recomendado
Precision Portable Instrumentation
Battery-powered precision instruments benefit from the MAX1207ETL+'s 316 mW power budget and 3.3V single-supply operation, which simplify power-tree design and extend runtime on lithium packs. The 12-bit 65 MSPS performance is well matched to handheld oscilloscope channels, data-acquisition loggers, and field-portable spectrum analyzers. Industrial -40C to +85C screening means the part remains reliable across outdoor and uncontrolled-thermal deployment scenarios.
Recomendado
Radar and Lidar Signal Acquisition
Automotive and industrial radar/lidar digitizer front ends can leverage the MAX1207ETL+ for short-range channel capture where 12-bit resolution and 65 MSPS suffice for amplitude-based ranging. The differential analog input rejects common-mode noise from long coax runs between the antenna and the digitizer board, while 88.7 dBc SFDR keeps spurious content below detection thresholds. For higher-bandwidth long-range channels, designers can scale up to the MAX1209ETL+T (80 MSPS) within the same footprint.
Recomendado
Industrial Process Control Digitizers
Process-control PLCs and industrial data-acquisition modules use the MAX1207ETL+ to digitize 4-20 mA loop signals, strain-gauge bridges, and other sensor front ends with 12-bit resolution at 65 MSPS oversampling ratios. The internal precision bandgap reference and common-mode reference output reduce external component count, while 316 mW power consumption keeps module heat dissipation within standard DIN-rail enclosure budgets. Industrial temperature screening ensures operation across factory floor thermal extremes.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para MAX1207ETL+ — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | MAX1206ETL+ | MAX1209ETL+ | MAX1207ETL+T |
|---|---|---|---|---|
| Brand | Analog Devices (Maxim Integrated) | Analog Devices (Maxim Integrated) | Analog Devices (Maxim Integrated) | Analog Devices (Maxim Integrated) |
| Package | TQFN-40 (5x5) | TQFN-40 (5x5) - same | TQFN-40 (5x5) - same | TQFN-40 (5x5) - same |
| Resolution | 12 bit | 12 bit | 12 bit | 12 bit |
| Sample Rate | 65 MSPS | 40 MSPS | 80 MSPS | 65 MSPS |
| Lifecycle Status | Obsolete (stock only) | Obsolete (stock only) | Obsolete (stock only) | Obsolete (stock only) |
Diferenciadores clave
- Pin-compatible higher sample-rate upgrade path (frente a MAX1209ETL+)
- Pin-compatible lower-power option available (frente a MAX1206ETL+)
- Industrial-grade temperature screening (frente a MAX1207ETL+T)
Notas de diseño
Power the MAX1207ETL+ from a clean 3.3V analog rail using a ferrite bead plus 0.1 uF/10 uF decoupling network placed within 5 mm of the AVDD and DVDD pins. The datasheet specifies 316 mW single-ended clock operation, so an LDO such as the ADP3330 supplying at least 400 mA ensures adequate transient headroom. Tie analog and digital grounds together only at a single point beneath the exposed pad to avoid ground-loop noise coupling into the T/H stage.
Solder the exposed pad (pin 40) to a continuous ground copper pour of at least 25 mm^2 to achieve the lowest junction-to-ambient thermal resistance and provide a low-inductance ground reference. Route analog input traces as a 100 ohm differential pair with controlled 50 ohm single-ended impedance and keep them at least 3 mm away from any digital output trace. Use length-matched clock traces if the differential clock mode is selected, with skew kept below 50 ps to preserve SNR.
Do not exceed the 3.6V absolute maximum analog supply, or the ESD diodes on the analog inputs will forward-bias and degrade linearity. Estimated: at 65 MSPS and full-scale input, the input-stage sampling capacitor draws charge spikes of roughly 5 mA peak per AVDD cycle, so AVDD trace inductance must be minimized or those spikes will inject noise into the reference. Decouple REFCAP with a 0.1 uF ceramic placed directly at the pin.
Información de cumplimiento
RoHS compliant per Maxim Integrated (now ADI) lead-free (+ suffix) finish. Not AEC-Q100 qualified; for automotive applications choose a dedicated AEC-Q100 qualified ADC.
