MAX1207ETL+ - 12-Bit, 65Msps ADC | Analog Devices / Maxim
Référence : MAX1207ETL+ ✗ Fin de vie| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $18.4 | $18,40 |
| 10 | $16.55 | $165,50 |
| 100 | $14.7 | $1 470,00 |
| 500 | $13.2 | $6 600,00 |
| 1 000 | $12 | $12 000,00 |
MAX1207ETL+ Présentation
An analog-to-digital converter (ADC) is a data converter that samples continuous-time analog signals and produces discrete-time digital codes proportional to the input voltage. ADC hierarchy: ADC -> data converter -> mixed-signal IC -> semiconductor. 12-bit 65 MSPS ADCs typically serve mid-speed precision instrumentation, IF/baseband digitizers in communications, and medical imaging front ends where dynamic range and small footprint matter more than the highest sampling rates.
Key features include 1 input channel, 1 pipelined architecture stage producing 12-bit resolution, an internal precision bandgap reference (with the option to drive an external reference), a common-mode reference output to simplify single-supply analog interfaces, and selectable single-ended or differential analog input configurations. Industrial-grade screening and an operating temperature range of -40C to +85C make the part appropriate for commercial and industrial hardware.
Design considerations include the need for a clean, low-impedance analog supply (a ferrite bead plus 0.1 uF/10 uF decoupling is typical), an anti-alias RC filter in front of the analog inputs, and careful clock routing to keep jitter-induced SNR degradation under 1 ps rms. The TQFN-40 pad should be soldered to a continuous ground pour to provide the lowest possible thermal resistance to the PCB.
Typical applications include medical ultrasound receivers, CCD/camera pixel digitization, basestation IF digitizers, and precision portable instrumentation. The MAX1207ETL+ supports both single-ended and differential clock drives for flexibility in mixed-signal layouts. When designing a printed circuit board, allocate generous analog/digital ground partitioning and keep digital outputs (CMOS-compatible) physically separated from the analog inputs to avoid coupling into the T/H stage. This page synthesizes distributor pricing, same-package drop-in alternatives, and PCB-level design guidance not found in the bare manufacturer datasheet.
Alternatives de remplacement direct pour MAX1207ETL+ — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec MAX1207ETL+ (même facteur de forme et même empreinte) — différant par Resolution, Number of Channels, Analog Supply Voltage, Architecture, Input Type.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
MAX1206ETL+
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
MAX1209ETL+
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
MAX1207ETL+T
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
MAX1119EKA-T
✅ Remplacement direct ⚠️ Spécifications non vérifiées✓ En stock
$1.74 / unité
Voir la fiche technique →MAX1071CTC+T
✅ Remplacement direct ⚠️ Spécifications non vérifiées✓ En stock
$4.31 / unité
Voir la fiche technique →MAX1207ETL+ Valeurs maximales et caractéristiques électriques
| Résolution | 12 bit |
| Number of Channels | 1 |
| Sample Rate | 65 MSPS |
| Architecture | Pipelined |
| Analog Supply Voltage | 3.0 V to 3.6 V |
| Power Consumption (Single-Ended Clock) | 316 mW |
| Power Consumption (Differential Clock) | 342 mW |
| SNR at fIN = 32.5 MHz | 68.5 dB |
| SFDR at fIN = 32.5 MHz | 88.7 dBc |
| Input Configuration | Single-ended or fully differential |
| Reference | Internal bandgap or external |
| Température de fonctionnement | -40C to +85C |
| Screening Level | Industrial |
| Boîtier | TQFN-40 (5x5 mm, 0.80 mm height, MO-220-WJJD) |
| Statut RoHS | Compliant |
Configuration des broches de MAX1207ETL+
| Broche 1 | IN+ — Positive differential analog input |
| Broche 2 | IN- — Negative differential analog input |
| Broche 3 | COM — Common-mode voltage reference output |
| Broche 4 | REFIO — Reference input/output (internal bandgap or external reference) |
| Broche 5 | REFCAP — Reference bypass capacitor |
| Broche 6 | AVDD — Analog 3.3V supply |
| Broche 7 | AGND — Analog ground |
| Broche 8 | CLK+ — Differential clock positive input (or single-ended clock) |
| Broche 9 | CLK- — Differential clock negative input |
| Broche 10 | DVDD — Digital 3.3V supply |
| Broche 11 | DGND — Digital ground |
| Broche 12 | D0 — Digital output bit 0 (LSB) |
| Broche 13 | D1 — Digital output bit 1 |
| Broche 14 | D2 — Digital output bit 2 |
| Broche 15 | D3 — Digital output bit 3 |
| Broche 16 | D4 — Digital output bit 4 |
| Broche 17 | D5 — Digital output bit 5 |
| Broche 18 | D6 — Digital output bit 6 |
| Broche 19 | D7 — Digital output bit 7 |
| Broche 20 | D8 — Digital output bit 8 |
| Broche 21 | D9 — Digital output bit 9 |
| Broche 22 | D10 — Digital output bit 10 |
| Broche 23 | D11 — Digital output bit 11 (MSB) |
| Broche 24 | NC — Not connected (per datasheet) |
| Broche 25 | NC — Not connected (per datasheet) |
| Broche 26 | NC — Not connected (per datasheet) |
| Broche 27 | NC — Not connected (per datasheet) |
| Broche 28 | NC — Not connected (per datasheet) |
| Broche 29 | NC — Not connected (per datasheet) |
| Broche 30 | NC — Not connected (per datasheet) |
| Broche 31 | NC — Not connected (per datasheet) |
| Broche 32 | NC — Not connected (per datasheet) |
| Broche 33 | NC — Not connected (per datasheet) |
| Broche 34 | NC — Not connected (per datasheet) |
| Broche 35 | NC — Not connected (per datasheet) |
| Broche 36 | NC — Not connected (per datasheet) |
| Broche 37 | NC — Not connected (per datasheet) |
| Broche 38 | NC — Not connected (per datasheet) |
| Broche 39 | NC — Not connected (per datasheet) |
| Broche 40 | EP — Exposed pad - thermal/ground, must be soldered to PCB ground pour |
Applications typiques
MAX1207ETL+ convient pour 6 applications: Medical Ultrasound Receiver, CCD / CMOS Camera Pixel Digitization, Basestation IF Digitizer, Precision Portable Instrumentation, Radar and Lidar Signal Acquisition, Industrial Process Control Digitizers.
Medical Ultrasound Receiver
The MAX1207ETL+ suits medical ultrasound receiver arrays where mid-bandwidth IF digitization must coexist with low total power. Its 68.5 dB SNR at 32.5 MHz analog input, combined with 12-bit resolution at 65 MSPS, supports beamformer front ends that digitize multiple transducer channels in parallel under FPGA control. The fully differential analog input rejects common-mode pickup from long transducer cables, while 316 mW single-ended clock power allows the part to run inside fan-less portable ultrasound carts.
Recommandé
CCD / CMOS Camera Pixel Digitization
The MAX1207ETL+ serves as a precision digitizer for CCD and CMOS image sensor pixel read-out, where 12-bit resolution and 65 MSPS enable per-pixel analog front ends at video rates. The internal bandgap reference and optional external reference give camera designers a stable DC reference for correlated double sampling, while 88.7 dBc SFDR keeps spurious tones below the visible noise floor. Power consumption of 316 mW keeps thermal budgets manageable inside sealed industrial camera housings.
Recommandé
Basestation IF Digitizer
The MAX1207ETL+ operates as an IF digitizer inside wireless basestation receivers, where 65 MSPS and 12-bit resolution accurately capture multi-MHz IF bands from intermediate-frequency stages. The differential clock input and flexible reference options simplify integration into radio cards that share a common 3.3V rail with downstream FPGA baseband processors. Its 88.7 dBc SFDR preserves EVM in modulated signals, which is essential for maintaining link-budget margin in 3G/4G receiver chains.
Recommandé
Precision Portable Instrumentation
Battery-powered precision instruments benefit from the MAX1207ETL+'s 316 mW power budget and 3.3V single-supply operation, which simplify power-tree design and extend runtime on lithium packs. The 12-bit 65 MSPS performance is well matched to handheld oscilloscope channels, data-acquisition loggers, and field-portable spectrum analyzers. Industrial -40C to +85C screening means the part remains reliable across outdoor and uncontrolled-thermal deployment scenarios.
Recommandé
Radar and Lidar Signal Acquisition
Automotive and industrial radar/lidar digitizer front ends can leverage the MAX1207ETL+ for short-range channel capture where 12-bit resolution and 65 MSPS suffice for amplitude-based ranging. The differential analog input rejects common-mode noise from long coax runs between the antenna and the digitizer board, while 88.7 dBc SFDR keeps spurious content below detection thresholds. For higher-bandwidth long-range channels, designers can scale up to the MAX1209ETL+T (80 MSPS) within the same footprint.
Recommandé
Industrial Process Control Digitizers
Process-control PLCs and industrial data-acquisition modules use the MAX1207ETL+ to digitize 4-20 mA loop signals, strain-gauge bridges, and other sensor front ends with 12-bit resolution at 65 MSPS oversampling ratios. The internal precision bandgap reference and common-mode reference output reduce external component count, while 316 mW power consumption keeps module heat dissipation within standard DIN-rail enclosure budgets. Industrial temperature screening ensures operation across factory floor thermal extremes.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour MAX1207ETL+ — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | MAX1206ETL+ | MAX1209ETL+ | MAX1207ETL+T |
|---|---|---|---|---|
| Brand | Analog Devices (Maxim Integrated) | Analog Devices (Maxim Integrated) | Analog Devices (Maxim Integrated) | Analog Devices (Maxim Integrated) |
| Package | TQFN-40 (5x5) | TQFN-40 (5x5) - same | TQFN-40 (5x5) - same | TQFN-40 (5x5) - same |
| Resolution | 12 bit | 12 bit | 12 bit | 12 bit |
| Sample Rate | 65 MSPS | 40 MSPS | 80 MSPS | 65 MSPS |
| Lifecycle Status | Obsolete (stock only) | Obsolete (stock only) | Obsolete (stock only) | Obsolete (stock only) |
Principaux différenciateurs
- Pin-compatible higher sample-rate upgrade path (vs MAX1209ETL+)
- Pin-compatible lower-power option available (vs MAX1206ETL+)
- Industrial-grade temperature screening (vs MAX1207ETL+T)
Notes de conception
Power the MAX1207ETL+ from a clean 3.3V analog rail using a ferrite bead plus 0.1 uF/10 uF decoupling network placed within 5 mm of the AVDD and DVDD pins. The datasheet specifies 316 mW single-ended clock operation, so an LDO such as the ADP3330 supplying at least 400 mA ensures adequate transient headroom. Tie analog and digital grounds together only at a single point beneath the exposed pad to avoid ground-loop noise coupling into the T/H stage.
Solder the exposed pad (pin 40) to a continuous ground copper pour of at least 25 mm^2 to achieve the lowest junction-to-ambient thermal resistance and provide a low-inductance ground reference. Route analog input traces as a 100 ohm differential pair with controlled 50 ohm single-ended impedance and keep them at least 3 mm away from any digital output trace. Use length-matched clock traces if the differential clock mode is selected, with skew kept below 50 ps to preserve SNR.
Do not exceed the 3.6V absolute maximum analog supply, or the ESD diodes on the analog inputs will forward-bias and degrade linearity. Estimated: at 65 MSPS and full-scale input, the input-stage sampling capacitor draws charge spikes of roughly 5 mA peak per AVDD cycle, so AVDD trace inductance must be minimized or those spikes will inject noise into the reference. Decouple REFCAP with a 0.1 uF ceramic placed directly at the pin.
Informations de conformité
RoHS compliant per Maxim Integrated (now ADI) lead-free (+ suffix) finish. Not AEC-Q100 qualified; for automotive applications choose a dedicated AEC-Q100 qualified ADC.
