MAX202EESE+ 5V RS-232 Transceiver, 16-SOIC | Analog Devices
N.º de pieza: MAX202EESE+ ✓ ActivoMAX202EESE+ Descripción general
An RS-232 transceiver is an interface circuit that connects a digital controller or UART to a serial communications link. It belongs to the interface IC hierarchy, where a line transceiver combines a transmitter for outbound data with a receiver for inbound data. The MAX202EESE+ provides the electrical conversion, voltage levels, and ESD protection required between low-voltage digital logic and a ±RS-232 communications port.
The device includes two driver channels and two receiver channels, allowing one RS-232 port to support bidirectional serial communication through four signal pins. Its integrated charge pump generates the bipolar voltage levels required by RS-232 without a separate negative supply. The manufacturer specifies EIA/TIA-232E and CCITT V.28 operation at data rates up to 120 kbps when loaded.
Electrical robustness is addressed by ±15 kV human-body-model ESD protection on the serial-interface pins. This protection improves tolerance for cable insertion, removal, and electrostatic discharge encountered in industrial equipment. Operating from a single +5 V rail also simplifies power architecture in systems where a negative supply would otherwise be required.
Typical uses include industrial serial consoles, instrumentation, data acquisition, point-of-sale equipment, security systems, and embedded control boards. The dual-driver, dual-receiver arrangement is particularly useful for systems that exchange commands and status data over one RS-232 connection while also supporting hardware handshaking signals.
PCB design should provide adequate bypass capacitance at the supply pins and route serial traces away from sensitive analog or high-speed digital nodes. Decoupling capacitors must be placed close to the device to minimize supply-current transients during edge transitions. The external connector and cable remain exposed to electrostatic discharge, so board-level grounding and enclosure design should supplement the IC's internal ESD protection.
This page combines the manufacturer's electrical capabilities with package-specific comparison data, replacement guidance, and practical PCB implementation notes. It is intended to help engineers identify whether the MAX202EESE+ fits a +5 V RS-232 design and how to evaluate compatible alternatives before committing a board layout.
Alternativas directas para MAX202EESE+ — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con MAX202EESE+ (mismo factor de forma y huella) — difiere en Product Type, ESD Protection, Supply Voltage, Interface Standard, Maximum Data Rate.
MAX202IDR
✅ Sustitución directaConsulte el precio
Ver hoja de datos →MAX203EESE+
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
MAX206EESE+
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
MAX232EESE+
✅ Sustitución directa ⚠️ Especificaciones sin verificarConsulte el precio
Ver hoja de datos →MAX206EAG+T
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
MAX202EESE+ Especificaciones
| Product Type | RS-232 line transceiver |
| Number of Drivers | 2 |
| Number of Receivers | 2 |
| Tensión de alimentación | +5 V |
| Maximum Data Rate | 120 kbps |
| ESD Protection | ±15 kV HBM |
| Standards Compatibility | EIA/TIA-232E and CCITT V.28 |
| Encapsulado | 16-pin SOIC |
| Recuento de pines | 16 pins |
| Tipo de montaje | Surface mount |
| Charge Pump | Integrated |
| Number of Transceiver Channels | 2 driver and 2 receiver channels |
Guía de configuración de pines de MAX202EESE+ 16-pin soic
Configuración de pines para MAX202EESE+ (encapsulado 16-pin soic). La numeración de pines, las funciones y los diagramas de conexión se definen en la hoja de datos del fabricante. Consúltela para conocer el footprint exacto y las directrices de soldadura.
No hay datos detallados de patillaje disponibles para MAX202EESE+.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
MAX202EESE+ es adecuado para 6 aplicacións: Industrial Serial Console, Instrumentation and Data Acquisition, Point-of-Sale Terminal, Security and Access-Control Equipment, Embedded Control Board, Legacy Equipment Upgrade.
Industrial Serial Console
The MAX202EESE+ fits an industrial console because it converts between controller logic and RS-232 using two drivers and two receivers while operating from a single +5 V rail. Its integrated charge pump eliminates the need for a separate negative supply, and its ±15 kV HBM protection adds transient tolerance at connector-facing pins. A typical circuit places supply-decoupling capacitors beside VCC and GND while routing the four line-driver and receiver connections to the serial connector. The 120 kbps maximum data rate is suitable for configuration links, status exchanges, and service protocols that do not require high-speed differential signaling. Verify the board’s operating-temperature grade and complete the enclosure’s electrostatic and EMC validation before deploying the interface in an industrial environment.
Recomendado
Instrumentation and Data Acquisition
The MAX202EESE+ is suitable for connecting a data-acquisition controller to RS-232 instruments because two drivers and two receivers support bidirectional commands and measurements. The +5 V supply requirement simplifies integration with controller logic that already operates from +5 V, while the integrated charge pump provides the bipolar RS-232 signaling required by the remote device. Its capability up to 120 kbps covers many legacy measurement protocols and avoids a separate negative rail around the interface IC. Place the bypass capacitor close to the supply pins and keep the serial traces away from analog input nodes to prevent switching transients from disturbing measurements. Confirm line-driver levels, receiver thresholds, and the complete pinout against the manufacturer datasheet before connecting laboratory or field equipment.
Recomendado
Point-of-Sale Terminal
A point-of-sale terminal can use the MAX202EESE+ for a compact bidirectional serial link to a printer, scanner, or customer display. The two transmitter channels and two receiver channels allow command traffic and status traffic to share one interface, while the 16-pin SOIC footprint supports dense controller-board layouts. Operation from one +5 V supply and the integrated charge pump reduce the number of external power rails. The ±15 kV HBM rating is useful when the serial connector is exposed to user-accessible equipment, although the connector shell, cable, and ground geometry still influence ESD performance. Keep the interface traces compact, provide local supply bypassing, and test the completed assembly for ESD and EMC compliance rather than treating IC protection as a complete system-level solution.
Recomendado
Security and Access-Control Equipment
The MAX202EESE+ is appropriate for access-control and security equipment that uses a wired RS-232 port for configuration, event reporting, or diagnostics. Two drivers and two receivers provide bidirectional communication, while the single +5 V operation simplifies power design in embedded controller assemblies. Its ±15 kV HBM ESD protection improves robustness at an exposed communication port, and its operation up to 120 kbps covers common device-management protocols. The implementation should use a low-impedance ground return, controlled connector geometry, and grounded enclosure bonding to improve electrostatic-event performance. Confirm the device temperature grade, verify auxiliary-pin behavior, and validate the full interface through cables and connectors because propagation delay and protection behavior can differ from the bare IC test conditions.
Recomendado
Embedded Control Board
The MAX202EESE+ adds an industry-standard RS-232 port to an embedded control board without requiring a separate negative supply. Its two drivers and two receivers support full-duplex serial communication alongside UART pins that operate at TTL or CMOS levels. The integrated charge pump and ±15 kV HBM protection make the device appropriate for legacy service ports and equipment-to-equipment links. In a compact PCB, place the decoupling capacitor close to the power pins and route the transceiver path away from clocks, sensors, and high-speed memory. The 120 kbps limit should be checked against the protocol timing, especially if the original system uses unusual baud rates or long cables. Use the manufacturer pin description when assigning supply, enable, receiver-output, and driver-input signals.
Recomendado
Legacy Equipment Upgrade
The MAX202EESE+ can modernize a legacy RS-232 interface when a board must retain a 16-pin SOIC footprint and +5 V supply architecture. Two drivers and two receivers match the common MAX202E channel arrangement, while integrated charge-pump circuitry simplifies conversion from controller logic to RS-232 levels. The documented MAX202IDR and MAX206EAG+T alternatives provide candidates for board reuse, but engineers should compare every pin and auxiliary function before substitution. Pay particular attention to shutdown polarity, fail-safe receiver state, enable timing, and line-driver amplitude. During retrofit, inspect connector pin numbering and ground continuity because legacy equipment often relies on chassis-ground behavior that differs from modern low-voltage grounding conventions.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para MAX202EESE+ — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | MAX202IDR | MAX203EESE+ | MAX206EESE+ | MAX232EESE+ | MAX206EAG+T |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC |
| Product Type | RS-232 line transceiver | RS-232 line transceiver | RS-232 line transceiver | RS-232 line transceiver | RS-232 line transceiver | RS-232 line transceiver |
| Number of Drivers | 2 | 2 | 2 | 2 | 2 | 2 |
| Number of Receivers | 2 | 2 | 2 | 2 | 2 | 2 |
| ESD Protection | ±15 kV HBM | ±15 kV HBM | ±15 kV HBM | ±15 kV HBM | ±15 kV HBM | ±15 kV HBM |
Diferenciadores clave
- Four-channel RS-232 interface in a 16-pin SOIC footprint (frente a MAX202IDR)
- Single +5 V operation with integrated charge pump (frente a MAX232EESE+)
- 120 kbps RS-232 operation with high-level ESD protection (frente a MAX206EAG+T)
Notas de diseño
Place the supply-bypass capacitor directly beside the MAX202EESE+ VCC and ground pins. The integrated charge pump creates edge-related supply current when the RS-232 drivers switch, so a long supply trace can create transient voltage on the logic rail. Use the capacitor value and placement specified in the manufacturer's application guidance, keep the loop area small, and provide a stable ground reference close to the device.
Route the four RS-232 line connections directly toward the connector while keeping them away from clocks, sensor inputs, crystal circuits, and memory buses. Maintain the intended ground-return path and avoid sharing narrow ground segments between the transceiver and sensitive analog circuitry. The ±15 kV HBM rating protects the IC's interface pins, but connector placement, chassis grounding, and cable design determine how much system-level stress reaches the device.
Do not substitute an RS-232 transceiver solely because it has a 16-pin SOIC package. Confirm pin names, driver inputs, receiver outputs, enable or shutdown behavior, fail-safe receiver state, supply voltage, and driver-output levels. MAX202IDR, MAX203EESE+, MAX206EESE+, MAX232EESE+, and MAX206EAG+T are relevant candidates, but each requires comparison with the complete MAX202EESE+ pin description before a drop-in decision is approved.
Información de cumplimiento
The '+' ordering suffix commonly identifies a lead-free ordering option, but no explicit RoHS, REACH, AEC-Q100, halogen-free, or conflict-minerals statement was found in the cited manufacturer and distributor pages. Confirm these attributes against the current manufacturer product documentation before release.