MAX202EEUE+T - 120kbps 5V RS-232 | Analog Devices
N.º de pieza: MAX202EEUE+T ✓ ActivoMAX202EEUE+T Descripción general
An RS-232 transceiver is an interface IC that converts logic-level signals between a host or controller and a RS-232 serial port. Its drivers translate low-voltage logic levels into RS-232 bipolar levels, while its receivers perform the reverse conversion. The MAX202EEUE+T belongs to the RS-232 transceiver hierarchy, which also includes line drivers, line receivers, interface controllers, and broader communication interface semiconductors.
The two-driver, two-receiver arrangement supports full-duplex serial communication through two data channels. Its 120kbps maximum data rate provides sufficient margin for common serial links while meeting the EIA/TIA-232E and CCITT V.28 specifications identified by Analog Devices. Integrated charge-pump circuitry generates the bipolar voltage required by RS-232 drivers from a single +5V supply, reducing the external power-supply complexity associated with older interface designs.
ESD protection is a central feature of this device. The manufacturer describes the MAX202E family as having ±15kV Human Body Model ESD protection, making the interface suitable for systems where cables and connectors can be exposed to electrostatic discharge. The MAX202EEUE+T combines that protection with integrated charge-pump operation in a compact 16-pin TSSOP package suited to dense industrial, instrumentation, and embedded-control equipment.
Typical uses include serial service ports, test and measurement equipment, industrial controllers, data-acquisition systems, and embedded systems that exchange data with RS-232 peripherals. Two channels can connect separate transmit and receive paths, while full-duplex operation allows the endpoint to send and receive simultaneously. The 120kbps rate is especially appropriate for configuration interfaces, diagnostic links, and legacy equipment connectivity rather than high-volume local-area networking.
When laying out a design, place the charge-pump capacitors and interface bypass capacitors close to their designated pins, and route the RS-232 traces away from sensitive analog or high-speed digital signals. Treat the external connector as an ESD entry point, use a suitable chassis and signal-ground strategy, and verify the complete interface against the system grounding requirements. The manufacturer datasheet is the authoritative source for pin assignment, capacitor values, and test conditions.
This product page combines the confirmed MAX202E specifications with package, sourcing, replacement, and design guidance. It also distinguishes true pin-compatible drop-in options from family members that use different packages, helping engineers avoid incorrect substitutions when reusing an existing PCB layout.
Alternativas directas para MAX202EEUE+T — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con MAX202EEUE+T (mismo factor de forma y huella) — difiere en Charge Pump, ESD Protection, Interface Standard, Product Type, Supply Voltage.
No hay alternativas directas disponibles para este producto.
Solicitar alternativasMAX202EEUE+T Especificaciones
| Product Type | RS-232 transceiver |
| Number of Drivers | 2 channels |
| Number of Receivers | 2 channels |
| Velocidad de datos | Up to 120kbps |
| Tensión de alimentación | +5V |
| Interface Standard | RS-232 |
| Compliance | EIA/TIA-232E and CCITT V.28 |
| ESD Protection | ±15kV HBM |
| Charge Pump | Integrated |
| Encapsulado | 16-pin TSSOP |
| Tipo de montaje | Surface mount |
Guía de configuración de pines de MAX202EEUE+T 16-pin tssop
Configuración de pines para MAX202EEUE+T (encapsulado 16-pin tssop). La numeración de pines, las funciones y los diagramas de conexión se definen en la hoja de datos del fabricante. Consúltela para conocer el footprint exacto y las directrices de soldadura.
No hay datos detallados de patillaje disponibles para MAX202EEUE+T.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
MAX202EEUE+T es adecuado para 6 aplicacións: Industrial Controller Serial Port, Test and Measurement Equipment, Embedded Data Acquisition, Serial Service and Diagnostic Port, Legacy Peripheral Connectivity, Secure Device Management Interface.
Industrial Controller Serial Port
The MAX202EEUE+T is appropriate for an industrial controller that must communicate with a service computer or peripheral through a legacy RS-232 link. Its two drivers and two receivers support full-duplex operation, while the 120kbps maximum rate covers configuration, diagnostic, and supervisory protocols. Operation from one +5V rail simplifies controller power design because the integrated charge pump generates the bipolar driver voltage internally. The ±15kV HBM protection also adds useful robustness at an exposed connector, although the finished system still needs appropriate grounding, shielding, and cable treatment.
Recomendado
Test and Measurement Equipment
The MAX202EEUE+T can connect laboratory instruments, fixture controllers, and calibration equipment to RS-232-capable computers. Two independent channels allow simultaneous command and response traffic, which is useful in control loops where full-duplex behavior simplifies software communication. The 120kbps rate is more than adequate for many legacy instrument-control protocols, and the integrated charge pump avoids a separate bipolar supply. Its 16-pin TSSOP format also supports compact front-panel and internal measurement designs while maintaining ±15kV HBM-rated interface protection.
Recomendado
Embedded Data Acquisition
The MAX202EEUE+T fits an embedded data-acquisition controller that must communicate with external sensors, laboratory modules, or service equipment through RS-232. Two driver and receiver channels can support two full-duplex links, while the 120kbps data rate suits command, status, and moderate measurement-data transfers. The single +5V architecture reduces the number of external power rails in compact embedded equipment, and the integrated charge pump simplifies implementation. Its TSSOP package is useful where board area is constrained, subject to careful pin assignment and charge-pump capacitor placement.
Recomendado
Serial Service and Diagnostic Port
A service or diagnostic connector is a strong application for the MAX202EEUE+T because legacy equipment commonly exposes RS-232 for firmware loading, status reporting, and parameter configuration. The device provides two transmit and two receive channels, allowing a controller to exchange commands and responses over a full-duplex link at up to 120kbps. Its ±15kV HBM protection is particularly relevant when the serial connector is accessible during installation or maintenance. The external connector still requires suitable chassis grounding and ESD strategy for a reliable industrial installation.
Recomendado
Legacy Peripheral Connectivity
The MAX202EEUE+T provides a practical bridge between modern +5V logic and legacy RS-232 peripherals such as printers, scanners, scales, or older laboratory devices. The 120kbps rate matches the performance class of many RS-232 and V.28 links, while the integrated charge pump permits operation without a separate negative supply rail. Two channels can manage two serial functions or provide full-duplex traffic on one port. The ±15kV HBM protection improves tolerance to electrostatic discharge encountered during routine cable handling.
Recomendado
Secure Device Management Interface
The MAX202EEUE+T can support a low-bandwidth management or backplane interface in security and communications equipment that retains an RS-232 service path. Two channels allow separate command and status connections, while 120kbps operation is suitable for configuration exchanges rather than bulk traffic. Its single +5V operation aligns with many digital subsystems, and the integrated charge pump minimizes external circuitry. The ±15kV HBM protection is valuable in chassis-mounted equipment where the serial connector may be touched during installation or service.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para MAX202EEUE+T — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto |
|---|---|
| Package | 16-pin TSSOP |
| Brand | Analog Devices |
| Interface Type | RS-232 transceiver |
| Number of Drivers | 2 |
| Number of Receivers | 2 |
| Maximum Data Rate | 120kbps |
| Supply Voltage | +5V |
| ESD Protection | ±15kV HBM |
| Charge Pump | Integrated |
| Compliance | EIA/TIA-232E and CCITT V.28 |
Diferenciadores clave
- Two-channel full-duplex RS-232 interface (frente a MAX202CSE+T)
- TSSOP footprint supports compact board layouts (frente a MAX202ECWE+T)
- Single-supply operation with integrated charge pump (frente a MAX202EESE+T)
Notas de diseño
Place the charge-pump capacitors and supply bypass capacitor directly beside the pins identified in the manufacturer pin table, keeping each loop short and symmetrical as shown in the datasheet application circuit. Avoid routing the high-voltage RS-232 driver outputs beneath sensitive analog circuitry. The 16-pin TSSOP footprint offers limited lead spacing, so inspect the land pattern and solder-mask geometry against the official package drawing before releasing artwork.
Keep the RS-232 connector, protection network, and transceiver driver/receiver paths together, and separate them from clocks, precision analog inputs, and high-speed digital routing. Ground the connector shell according to the product's EMC architecture rather than assuming a universal signal-ground connection. Inexpensive MAX202EEUE+T implementations benefit greatly from short return paths because long exposed traces can re-couple transient energy that internal ESD protection alone cannot eliminate.
Do not substitute a narrow-SOIC or wide-SOIC MAX202E variant for the MAX202EEUE+T on an existing TSSOP board. The packages have different footprints and may also differ in terminal assignment, so they are not drop-in replacements. Likewise, do not omit the manufacturer-specified charge-pump capacitors: although the charge pump is integrated, the external capacitor network remains part of the circuit and affects operation. Verify pin names and values against the official datasheet.
Información de cumplimiento
The product excerpts identify EIA/TIA-232E and CCITT V.28 interface compliance but do not state component-level environmental or material compliance. AEC-Q100 is not applicable to this RS-232 interface IC.