Maxim Integrated

MAX202EEWE-T - 2/2 120kbps RS-232 Transceiver | Maxim

N.º de pieza: MAX202EEWE-T ✓ Activo
4.5 V to 5.5 V Vdss 16-pin wide SOIC Package
MOQ: 1 |

MAX202EEWE-T Descripción general

The Maxim Integrated MAX202EEWE-T is a 2-driver, 2-receiver RS-232 transceiver designed for data rates up to 120 kbps and operation from a single 5 V supply. It is packaged in a 16-pin wide SOIC package and incorporates an on-chip charge pump. The device provides ±15 kV human-body-model ESD protection and meets EIA/TIA-232E and CCITT V.28 interface requirements.

An RS-232 transceiver is an interface IC that bridges a logic-level UART or other serial controller and a physical RS-232 port. It combines line drivers, which convert low-voltage logic signals into RS-232 levels, with receivers, which convert bipolar RS-232 signals back into logic levels. Within the hierarchy of interface ICs, it is a dedicated serial-interface transceiver for point-to-point industrial, instrumentation, and embedded communications.

The MAX202EEWE-T provides two transmit channels and two receive channels, allowing full-duplex RS-232 communication from one package. Its maximum specified data rate of 120 kbps covers legacy serial links, industrial equipment, barcode systems, and control interfaces. Operation from a single 5 V supply simplifies system power design because the integrated charge pump generates the negative voltage required by the RS-232 drivers.

The device's integrated charge pump and single-supply architecture eliminate the external negative rail and associated charge-pump capacitors normally required by discrete RS-232 interface designs. Its 16-pin SOIC package is a surface-mount package in the SOIC family, and the EWE ordering code identifies the wide SOIC, tape-and-reel configuration. A complete 16-pin pin description is required before assigning PCB tracks or confirming connector-side signal names.

Typical uses include RS-232 links between microcontrollers and industrial peripherals, test and measurement instruments, service consoles, security equipment, and legacy data-acquisition systems. The two-driver, two-receiver arrangement is particularly useful for full-duplex links that carry data in both directions through one RS-232 port.

For PCB implementation, keep the supply bypass capacitor close to the V+ and ground connections, route driver and receiver outputs away from sensitive low-level signals, and treat the exposed connector-side pins as harsh industrial environments. The ±15 kV HBM rating provides useful device protection, but it does not eliminate the need for system-level surge and ESD mitigation.

This page combines the manufacturer interface specifications, ordering-code details, practical PCB guidance, and verified drop-in alternatives. It also identifies where pinout, package quantity, and compliance details require confirmation from the official MAX202E datasheet before production release.

Alternativas directas para MAX202EEWE-T — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.

Variantes de esta serie

Modelos de la misma serie compatibles directamente con MAX202EEWE-T (mismo factor de forma y huella) — difiere en Mounting Type, Nominal Supply Voltage.

Analog Devices
Mounting Type: Surface mount
Nominal Supply Voltage: +5 V
Comparar con MAX202EEWE-T →

MAX202EWE+T

✅ Sustitución directa
Analog Devices
📦 16-SOIC wide
RS-232 transceiver · 2 channels · 2 channels · 4.5 V to 5.5 V · +5 V · 120 kbps · ±5 V EIA/TIA-232E · 0.1 µF

Consulte el precio

Ver hoja de datos →

MAX202ECWE+T

✅ Sustitución directa
Analog Devices
📦 16-SOIC wide
RS-232 transceiver · 2 · 2 · Full duplex · 120 kbps · +5 V · ±15 kV human body model · EIA/TIA-232E and CCITT V.28

Consulte el precio

Ver hoja de datos →

TRS202E

✅ Sustitución directa
📦 16-SOIC
Pin-for-pin MAX202 replacement with the same 2/2 RS-232 function and 5 V supply; TI specifies enhanced IEC61000-4-2 ESD protection, while the target is specified at ±15 kV HBM.

📋 Alternativa de referencia (no en el catálogo)

MAX202EEWE-T Especificaciones

Driver/Receiver Configuration 2 drivers / 2 receivers
Transceiver Type 2/2 full-duplex RS-232 transceiver
Maximum Data Rate 120 kbps
Supply Voltage Range 4.5 V to 5.5 V
Nominal Supply Voltage 5 V
ESD Protection ±15 kV HBM
Interface Standard EIA/TIA-232E and CCITT V.28
Integrated Charge Pump Yes
Encapsulado 16-pin wide SOIC
Package Width 7.50 mm
Tipo de montaje Surface-mount SMD
Packaging Tape and reel

Guía de configuración de pines de MAX202EEWE-T 7.50 mm

Configuración de pines para MAX202EEWE-T (encapsulado 7.50 mm). La numeración de pines, las funciones y los diagramas de conexión se definen en la hoja de datos del fabricante. Consúltela para conocer el footprint exacto y las directrices de soldadura.

Diagrama de patillaje del encapsulado 7.50 mm para MAX202EEWE-T

No hay datos detallados de patillaje disponibles para MAX202EEWE-T.

Consulte la hoja de datos para ver la configuración completa de patillas.

Aplicaciones típicas

MAX202EEWE-T es adecuado para 6 aplicacións: Industrial Controller Serial Port, Test and Measurement Instrument, Service Console and Configuration Port, Embedded Data Acquisition Unit, Security and Access Equipment, Legacy Serial Adapter.

🏭

Industrial Controller Serial Port

The MAX202EEWE-T is appropriate for an industrial controller that must communicate with a legacy RS-232 instrument over a full-duplex link. Its two drivers and two receivers provide balanced channel count for bidirectional traffic, while the 120 kbps maximum data rate covers many UART-based control protocols. Single 5 V operation is useful where a negative rail would otherwise require a charge-pump circuit. The manufacturer rates the interface for EIA/TIA-232E and CCITT V.28 operation and includes ±15 kV HBM ESD protection. In a finished controller, add connector-side surge protection and maintain a low-impedance ground path between the transceiver and the connected equipment.

🔧

Test and Measurement Instrument

The MAX202EEWE-T can provide the host-side RS-232 interface in test and measurement equipment that uses an asynchronous serial command set. The 2/2 channel arrangement supports transmit and receive paths within one device, and the 120 kbps capability is suitable for many instrument-control protocols operating below that limit. Because the device needs only a 5 V supply, instrument designers can avoid a separate negative RS-232 rail. The integrated charge pump and ±15 kV HBM protection are valuable in benchtop and production-test environments where the serial connector is handled frequently, although external protection may still be needed for surge events.

💻

Service Console and Configuration Port

The MAX202EEWE-T fits a service console or configuration interface that must connect a controller board to a computer or maintenance terminal. Two drivers and two receivers allow full-duplex command and response traffic, while the 120 kbps rate is compatible with many legacy serial consoles. Its single 5 V supply requirement simplifies auxiliary interface design in systems that already operate from 5 V. The 16-pin wide SOIC package is also practical for automated board assembly. Place the interface close to the connector, keep ground return paths short, and use appropriate external protection when the cable can be connected or disconnected during operation.

🖥️

Embedded Data Acquisition Unit

The MAX202EEWE-T can serve as the RS-232 interface on an embedded data-acquisition unit that must exchange commands and sampled data with a host computer. The 120 kbps ceiling provides ample bandwidth for many low-rate telemetry protocols and avoids the complexity of a modern high-speed physical layer. The integrated charge pump removes the need for an external negative voltage generator, while the device's 2/2 organization supports simultaneous transmit and receive paths. For deployments near motors, relays, or long external cables, add coordinated grounding and connector-side surge protection because device ESD ratings do not by themselves suppress system-level transients.

🔐

Security and Access Equipment

The MAX202EEWE-T is suitable for access-control and security equipment that exposes a wired RS-232 configuration or status port to a technician's terminal. The device provides the required EIA/TIA-232E and CCITT V.28 interface behavior at rates up to 120 kbps, along with ±15 kV HBM ESD protection for handling-sensitive environments. Its integrated charge pump and single 5 V operation reduce the number of power rails required beside the controller. The final enclosure should still define cable length, grounding, and surge requirements, because the transceiver rating addresses device-level ESD immunity rather than complete protection of the external port.

🔌

Legacy Serial Adapter

The MAX202EEWE-T can be used in a compact legacy serial adapter that converts a modern controller connector to an RS-232 port. The 16-pin wide SOIC package supports compact surface-mount construction, while two drivers and two receivers enable a full-duplex interface. Operation from 4.5 V to 5.5 V provides flexibility around common 5 V systems, and the integrated charge pump supplies the interface voltage needed by RS-232 drivers. At the board boundary, include a defined signal ground, route outputs away from sensitive logic, and select external protection according to the maximum cable exposure and installation environment.

What is the MAX202EEWE-T?
The MAX202EEWE-T is a 2-driver, 2-receiver RS-232 transceiver operating from a single 5 V supply at data rates up to 120 kbps. According to the Maxim Integrated MAX202E datasheet, it includes an integrated charge pump and ±15 kV HBM ESD protection. It is intended for full-duplex RS-232 and V.28 links and is supplied in a 16-pin wide SOIC package.
What are the key specifications of MAX202EEWE-T that engineers should know?
The principal MAX202EEWE-T specifications are 2 RS-232 drivers, 2 receivers, a 4.5 V to 5.5 V supply range, and operation up to 120 kbps. The device also provides ±15 kV human-body-model ESD protection and meets EIA/TIA-232E and CCITT V.28 requirements. Its integrated charge pump permits single-supply operation, while the EWE code identifies a 16-pin wide SOIC tape-and-reel configuration.
Where can I download the MAX202EEWE-T datasheet PDF?
The official MAX202EEWE-T datasheet is the MAX202E-MAX241E PDF published by Maxim Integrated at analog.com. It covers the MAX202E family, including the MAX202EEWE-T ordering configuration, electrical characteristics, interface behavior, and package information. Use the manufacturer PDF when defining pin connections, supply bypassing, ESD handling, and production test limits.
Where can I find the MAX202EEWE-T pinout?
The MAX202EEWE-T pin assignment is contained in the pin-description section of the official MAX202E-MAX241E datasheet. The EWE version uses a 16-pin wide SOIC footprint, but connector-side signal labels should be taken directly from the pin-description table rather than inferred from another MAX202 package. That verification is especially important because narrow SOIC, wide SOIC, and TSSOP options may use different package codes.
Does the MAX202EEWE-T need a negative supply voltage?
No external negative supply is required for normal operation. The MAX202EEWE-T uses its integrated charge pump to support RS-232 driver operation from a single 5 V supply. This simplifies the power tree compared with older RS-232 interfaces that require a separate negative rail and charge-pump components. The external circuit still needs local supply bypassing and appropriate grounding.
What data rate does the MAX202EEWE-T support?
The MAX202EEWE-T supports RS-232 data rates up to 120 kbps when loaded. According to the Maxim Integrated product page, the MAX202E family meets EIA/TIA-232E and CCITT V.28 specifications at rates up to 120 kbps. This makes the device appropriate for legacy UART links, industrial controllers, instrumentation, and service interfaces, but not for modern high-speed serial protocols.
What ESD protection does the MAX202EEWE-T provide?
The MAX202EEWE-T provides ±15 kV human-body-model ESD protection on its RS-232 interface. This rating describes the device-level protection verified for harsh communications environments. It does not replace a correctly designed protection network at an exposed connector, particularly where cables can extend outside an enclosure or where system-level surge requirements are more severe.
Where can I buy MAX202EEWE-T online?
Use the Request a Quote form on this page to request MAX202EEWE-T pricing, stock confirmation, and lead time for the exact tape-and-reel ordering code. The quote request should identify MAX202EEWE-T and the desired quantity so the order can be matched to the 16-pin wide SOIC configuration. No distributor is recommended by name because availability and commercial terms can change.
What is the price of MAX202EEWE-T?
Current pricing for MAX202EEWE-T should be requested through the Request a Quote form on this page. The structured quote flow is used because component pricing, stock, and lead time vary with order quantity and market conditions. Submit the exact MPN and required reel quantity to obtain an actionable commercial response rather than a generic family price.
What is the lead time for MAX202EEWE-T?
Request the current MAX202EEWE-T lead time through the Request a Quote form on this page. Include the annual and per-reel quantities, the desired ship date, and whether multiple sourcing sites must be supported. A quantity-specific lead-time confirmation is more useful for production planning than a generic stock estimate for the MAX202E family.
Is MAX202EEWE-T in stock?
Stock for the exact MAX202EEWE-T ordering code should be confirmed through the Request a Quote form on this page. When requesting stock, state the reel quantity and target delivery date. This avoids confusing the MAX202EEWE-T tape-and-reel configuration with other MAX202E package and temperature-grade options.
What is the difference between MAX202EEWE-T and TRS202E?
MAX202EEWE-T is a Maxim Integrated 2/2 RS-232 transceiver rated for 120 kbps, with ±15 kV HBM ESD protection and single 5 V operation. Texas Instruments identifies TRS202E as a pin-for-pin MAX202 replacement with the same functional pinout and enhanced IEC61000-4-2 ESD protection. Confirm package variant, temperature range, and exact pin mapping in the device-specific datasheet before substitution.
When should I choose MAX202EEWE-T over TRS202E?
Choose MAX202EEWE-T when the design is already qualified around the Maxim MAX202E 16-pin wide SOIC implementation and its ±15 kV HBM protection is sufficient. Consider TRS202E when a pin-for-pin second source with enhanced IEC61000-4-2 system-level ESD protection is required. Final selection should account for exact package code, operating-temperature grade, availability, and qualification status.
What can replace MAX202EEWE-T?
TRS202E is a documented pin-for-pin replacement for the MAX202 and is the strongest cross-brand drop-in candidate identified. The MAX202E family also includes related wide-SOIC order codes such as MAX202EWE+T and MAX202ECWE+T, but their ordering suffixes and production status should be checked before use. Use the Request a Quote form to request availability for the exact replacement MPN.
Is MAX202EEWE-T suitable for an industrial RS-232 port?
The MAX202EEWE-T is suitable for many industrial RS-232 links because it supports 120 kbps, single 5 V operation, EIA/TIA-232E, CCITT V.28, and ±15 kV HBM protection. The industrial suitability of the finished product also depends on the operating-temperature grade, connector protection, isolation strategy, and enclosure. Confirm those requirements against the official electrical and package specifications.

Datos de referencia de ingeniería para MAX202EEWE-T — comparación, orientación de diseño e información de cumplimiento.

Guía de selección

Choose MAX202EEWE-T when the PCB is designed around the 16-pin wide SOIC MAX202E interface and the required protection is ±15 kV HBM. It combines two drivers, two receivers, single 5 V operation, an integrated charge pump, and 120 kbps data-rate capability. Select MAX202EWE+T or MAX202ECWE+T when the exact ordering code is preferable for an approved second source, after confirming temperature grade, lifecycle status, and pin mapping. Consider TRS202E for a pin-for-pin cross-brand strategy or when enhanced IEC61000-4-2 ESD protection is explicitly required by the product specification. Do not substitute narrow-SOIC or TSSOP MAX202E options without a PCB redesign. Regardless of the chosen ordering code, verify the official pin table, capacitor requirements, operating-temperature range, and connector protection before releasing a production design.

Comparación con alternativas

Parámetro Este producto MAX202EWE+T MAX202ECWE+T TRS202E
Package 16-SOIC wide 16-SOIC wide 16-SOIC wide 16-SOIC
Brand Maxim Integrated Maxim Integrated Maxim Integrated Texas Instruments
Driver/Receiver Configuration 2/2 2/2 2/2 2/2
Maximum Data Rate 120 kbps 120 kbps 120 kbps 120 kbps
Supply Voltage Range 4.5 V to 5.5 V 4.5 V to 5.5 V 4.5 V to 5.5 V 4.5 V to 5.5 V
Single-Supply Operation Yes Yes Yes Yes
ESD Protection ±15 kV HBM ±15 kV HBM ±15 kV HBM Enhanced IEC61000-4-2 ESD protection
Interface Standards EIA/TIA-232E and CCITT V.28 EIA/TIA-232E and CCITT V.28 EIA/TIA-232E and CCITT V.28 RS-232 / V.28
Integrated Charge Pump Yes Yes Yes Yes

Diferenciadores clave

  • Full-duplex 2/2 RS-232 channel arrangement (frente a TRS202E)
  • 120 kbps RS-232 operation from a single 5 V supply (frente a MAX202EWE+T)
  • Manufacturer-specified ±15 kV HBM ESD protection (frente a TRS202E)

Notas de diseño

Place the local 5 V bypass capacitor as close as practical to the device supply and ground pins. The MAX202EEWE-T operates from 4.5 V to 5.5 V and uses an integrated charge pump, so the external supply network must provide a low-impedance 5 V rail while keeping switching and digital currents away from the analog reference return. Verify capacitor voltage rating, effective capacitance after DC-bias derating, and trace resistance against the load transient requirements of the finished interface.

Use the official 16-pin pin-description table when laying out the wide SOIC footprint. Do not infer connector-side signal names from a narrow SOIC or TSSOP variant because the package drawings may place the same functional signals on different pins. Keep driver outputs and receiver inputs away from clocks, reset signals, and precision analog traces. Provide a direct ground return to the connector reference where possible, and keep the RS-232 traces short relative to the external cable.

The MAX202EEWE-T provides ±15 kV HBM device-level ESD protection, but a cable-connected interface can also experience system-level surges and discharges that exceed that rating. Add a connector-side protection network when the port is accessible, selected for the data rate, line impedance, and installation environment. Keep the protected connector section physically separate from sensitive logic and route surge current directly to chassis or signal ground according to the product's grounding strategy.

Do not treat every MAX202E suffix as electrically and mechanically interchangeable. The wide SOIC, narrow SOIC, and TSSOP order codes have different footprints, and reel or temperature suffixes can change how the component is ordered. Before substitution, verify the exact package width, pin count, pin names, temperature grade, and lifecycle status. For a board already laid out for the MAX202EEWE-T, compare the candidate directly against the official pin table rather than relying only on the family name.

Información de cumplimiento

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Libre de plomo
Unknown
Libre de halógenos
Unknown
Minerales en conflicto
Unknown

The interface supports EIA/TIA-232E and CCITT V.28 and has ±15 kV HBM ESD protection. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations require confirmation from the manufacturer product page or declaration.

Búsquedas relacionadas

MAX202EEWE-T datasheet MAX202EEWE-T pinout MAX202EEWE-T datasheet pdf MAX202EEWE-T specifications MAX202EEWE-T price MAX202EEWE-T stock MAX202EEWE-T equivalent MAX202EEWE-T replacement MAX202EEWE-T vs TRS202E Maxim Integrated MAX202EEWE-T MAX202EEWE-T 16-SOIC MAX202EEWE-T RS-232 application circuit

Componentes & términos relacionados

Maxim Integrated MAX202EEWE-T MAX202E MAX202EWE+T MAX202ECWE+T TRS202E Texas Instruments RS-232 transceiver RS-232 EIA/TIA-232E CCITT V.28 line driver line receiver full duplex integrated charge pump single 5 V supply 120 kbps ±15 kV HBM ESD protection 16-SOIC wide SOIC family surface-mount package tape and reel packaging industrial controller test and measurement interface
RFQ de presupuesto rápido
Complete los detalles — nuestro equipo de ventas responderá en un plazo de 24 horas
Número de pieza Fabricante Encapsulado QTY Precio objetivo Total
✓
¡Presupuesto enviado!

Responderemos a su correo electrónico en un plazo de 24 horas

1
RFQ enviado
2
Presupuesto recibido
3
Pedido realizado
4
Pago
5
Enviado
6
Entregado
Ver detalles del RFQ