Analog Devices

MAX303CPE+ - Dual High-Speed SPDT Analog Switch | Analog Devices

N.º de pieza: MAX303CPE+ ✓ Activo
10 V to 30 V Vdss Less than 250 pA Id Less than 35 ohm Rds(on) 16-pin plastic DIP Package
MOQ: 1 |

MAX303CPE+ Descripción general

The Analog Devices MAX303CPE+ is a precision, dual, high-speed analog switch with two independently controlled single-pole double-throw channels, a maximum on-resistance of 35 ohms, and operation across positive and negative supply voltages. The device is packaged as a 16-pin plastic DIP and provides two normally open and two normally closed switch poles for routing bipolar analog signals.

An analog switch is a semiconductor device that connects or disects circuit paths under digital control. Unlike a mechanical relay, it can change state rapidly with low control-signal power and without mechanical contact wear. The MAX303 belongs to the interface-IC hierarchy as a precision analog switch and multiplexer. Its matched channels, low leakage, and low on-resistance make it useful where signal integrity must be maintained during measurement, acquisition, or signal-routing operations.

The MAX303CPE+ supports two supply rails, allowing operation from positive to negative voltage when the control input thresholds are compatible with the host logic. Its on-resistance is specified below 35 ohms, and the two channels are guaranteed to match within 2 ohms. These characteristics improve channel-to-channel consistency when the same signal level must be presented to multiple downstream nodes. The device also provides low leakage, reported as below 250 pA at 25°C and below 6 nA at 85°C.

Each channel contains one normally open and one normally closed path. This arrangement allows a signal to be routed to one of two destinations, or provides break-before-make behavior when the control state changes. The MAX303 family is designed for precision, high-speed signal switching, where on-resistance variation, off-state leakage, and channel matching can affect measurement accuracy. The exact switching timing, logic levels, and supply limits should be confirmed in the manufacturer data sheet before final circuit release.

Typical uses include precision test and measurement systems, automated instrumentation, data-acquisition front ends, sample-and-hold circuitry, and bipolar signal-routing networks. In these systems, the MAX303CPE+ can route a sensor or reference signal between measurement paths while keeping insertion resistance and leakage predictable. Its dual-channel architecture reduces component count when two related signals must be selected independently.

PCB layout should preserve short return paths and minimize capacitance around signal and control pins. Keep analog traces away from fast switching clocks and high-current paths, and use a solid ground reference to reduce coupling into the selected channel. Because the part uses a through-hole plastic DIP package, connector and socket accessibility should be checked against mechanical height, cleaning requirements, and assembly-service constraints before releasing the production design.

This product page organizes the MAX303CPE+ electrical characteristics, package information, qualified drop-in alternatives, and practical design guidance for engineers evaluating dual SPDT analog switching. It also distinguishes the lead-free MAX303CPE+ ordering code from the closely related MAX303CPE catalog entry while preserving the distinction between verified drop-in interchangeability and merely similar products.

Alternativas directas para MAX303CPE+ — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.

Variantes de esta serie

Modelos de la misma serie compatibles directamente con MAX303CPE+ (mismo factor de forma y huella) — difiere en On-Resistance, Package.

Analog Devices
On-Resistance: 100 ohm
Package: 16-pin PDIP
Comparar con MAX303CPE+ →

MAX303CPE

✅ Sustitución directa
📦 16-pin plastic DIP
Ordering suffix differs by the lead-free plus designation; documented switch ratings remain the same, including less than 35 ohm on-resistance and 2 ohm channel matching

📋 Alternativa de referencia (no en el catálogo)

MAX303CPE+ Valores máximos y características eléctricas

Device Type Precision, dual, high-speed analog switch
Number of Channels 2 channels
Switch Configuration 2:1 SPDT per channel
On-Resistance Less than 35 ohm
On-Resistance Matching Between Channels Within 2 ohm
Normally Open Paths 2 paths
Normally Closed Paths 2 paths
Leakage Current at 25°C Less than 250 pA
Leakage Current at 85°C Less than 6 nA
Positive Supply Voltage 10 V to 30 V
Negative Supply Voltage -4.5 V to -20 V
Encapsulado 16-pin plastic DIP
Tipo de montaje Through-hole

Guía de configuración de pines de MAX303CPE+ 16-pin plastic dip

Configuración de pines para MAX303CPE+ (encapsulado 16-pin plastic dip). La numeración de pines, las funciones y los diagramas de conexión se definen en la hoja de datos del fabricante. Consúltela para conocer el footprint exacto y las directrices de soldadura.

Diagrama de patillaje del encapsulado 16-pin plastic dip para MAX303CPE+

No hay datos detallados de patillaje disponibles para MAX303CPE+.

Consulte la hoja de datos para ver la configuración completa de patillas.

Aplicaciones típicas

MAX303CPE+ es adecuado para 6 aplicacións: Precision Test and Measurement Systems, Data Acquisition Front Ends, Bipolar Signal Routing, Sample-and-Hold Signal Selection, Automated Instrumentation, Laboratory Signal Switching.

🔧

Precision Test and Measurement Systems

The MAX303CPE+ fits precision test systems that route a source or measurement signal between two instrument paths. Its two independent SPDT channels allow two related selections to be controlled separately, while the less-than-35-ohm on-resistance limit supports relatively low-distortion signal routing. Channel resistance is specified to match within 2 ohms, which helps maintain calibration consistency between the two paths. Leakage below 250 pA at 25°C is also beneficial when the source impedance is high. The practical consideration is to keep connected cables and relay contacts from dominating the leakage budget around the switch.

📊

Data Acquisition Front Ends

The MAX303CPE+ is suitable for data-acquisition front ends that must select between two sensor, reference, or excitation paths. Its two SPDT channels reduce the number of discrete routing elements needed when paired signals require independent selection. The maximum 35-ohm on-resistance and guaranteed 2-ohm channel match provide predictable behavior during calibration, while the low-leakage characteristic supports high-source-impedance sensors. Place the device close to the analog input stage, use short traces, and maintain a quiet ground reference to prevent connector and board contamination from dominating the leakage floor.

⚡

Bipolar Signal Routing

The MAX303CPE+ can route bipolar signals because it operates with positive and negative supply rails rather than being limited to a single-polarity domain. The documented rail ranges are 10 V to 30 V and -4.5 V to -20 V. Its low on-resistance limits the voltage-drop burden when the switched source impedance is not negligible, while the normally open and normally closed paths support both source selection and signal isolation. The circuit must maintain each signal terminal inside the absolute maximum limits, including during control-state transitions.

📈

Sample-and-Hold Signal Selection

The MAX303CPE+ is appropriate for sample-and-hold front ends that need to select one of two candidate signals before conversion or storage. Two independently switched SPDT channels can handle complementary or parallel selections, and the less-than-35-ohm on-resistance helps limit acquisition-voltage error relative to higher-impedance switches. The 2-ohm channel-match guarantee improves consistency when both channels feed sensitive downstream stages. Pay particular attention to switching transients and control timing because acquisition accuracy can also be affected by charge injection and hold-settling behavior.

🏭

Automated Instrumentation

The MAX303CPE+ supports automated instrumentation that repeatedly connects a common source to one of two destinations. The dual SPDT arrangement is useful in scanner, matrix, and programmable-measurement systems where route isolation and repeatable resistance matter. The specified on-resistance ceiling of 35 ohms and channel matching within 2 ohms provide useful bounds for impedance and calibration calculations. For long switch lifetimes, choose connector and socket components that do not introduce a larger contact-resistance variation than the IC itself, and keep sensitive routes physically separated from actuator and relay wiring.

🔬

Laboratory Signal Switching

The MAX303CPE+ is well suited to laboratory signal switching where a single input must be selected among two paths and leakage can affect small-signal measurements. Leakage below 250 pA at 25°C and below 6 nA at 85°C provides a defined starting point for error budgeting, while the sub-35-ohm resistance limit reduces insertion loss for moderate source impedances. Use short, guarded analog traces and clean connectors, particularly when working with femtoamp- or picoamp-level leakage requirements. Temperature rise can increase leakage, so account for warm operating conditions rather than relying only on the 25°C figure.

Resumen de productos recomendados

MAX303CPE Closely related dual SPDT catalog variant Se usa en: Precision Test and Measurement Systems, Data Acquisition Front Ends, Bipolar Signal Routing, Sample-and-Hold Signal Selection, Automated Instrumentation, Laboratory Signal Switching MAX305CPE Same high-speed analog-switch family with a different topology Se usa en: Precision Test and Measurement Systems, Bipolar Signal Routing, Automated Instrumentation MAX301CPE Same analog-switch family with normally open topology Se usa en: Data Acquisition Front Ends, Sample-and-Hold Signal Selection, Laboratory Signal Switching
What is the MAX303CPE+ used for?
The MAX303CPE+ is a precision, dual, high-speed analog switch used to route one of two signal paths with two independent SPDT channels. It provides a maximum on-resistance below 35 ohms, two normally open paths, and two normally closed paths. According to the Analog Devices MAX303 data sheet, the channels are guaranteed to match within 2 ohms, making the device useful in test-and-measurement, data-acquisition, and precision analog-routing systems.
What are the key specifications of MAX303CPE+?
The MAX303CPE+ provides two independent 2:1 SPDT channels in a 16-pin plastic DIP package. Its key electrical specifications include less than 35 ohms on-resistance, channel matching within 2 ohms, and leakage below 250 pA at 25°C. The Analog Devices MAX303 data sheet also identifies positive and negative supply operation, with cited ranges of 10 V to 30 V and -4.5 V to -20 V, respectively.
Is MAX303CPE+ pin-compatible with MAX303CPE?
The MAX303CPE and MAX303CPE+ use the same 16-pin plastic DIP package and represent closely related lead-free catalog variants. Their core switch configuration and principal electrical characteristics remain aligned, including the 2:1 SPDT architecture, on-resistance below 35 ohms, and channel matching within 2 ohms. Verify the exact ordering-code definitions, temperature grade, and manufacturer data sheet before approving either part for a released design.
What is the difference between MAX303CPE+ and MAX303CPE?
The principal documented distinction is the ordering suffix: MAX303CPE+ is the lead-free version of the MAX303CPE device. Both are identified as 16-pin plastic DIP, two-channel 2:1 SPDT analog switches with less than 35 ohms on-resistance. The Analog Devices MAX303 family page should be used to confirm lead status and any grade-specific ordering differences before a procurement or qualification decision.
Where can I download the MAX303CPE+ datasheet PDF?
The MAX303CPE+ data sheet is available through the Analog Devices MAX303 product page and through the linked MAX303CPE PDF. The manufacturer page identifies the MAX303 family as production devices and provides the Precision, Dual, High-Speed Analog Switches data sheet, revision 1. Use the Analog Devices document as the controlling source for pin assignments, switching characteristics, absolute maximum ratings, and test conditions.
Where can I find the MAX303CPE+ pinout?
The MAX303CPE+ pinout is documented in the MAX303CPE data sheet, whose eight-page PDF covers the 16-pin plastic DIP device. Because a complete, numbered pin description is not reproduced on this product page, use the manufacturer pin-description table when assigning PCB nets. Confirm signal names, control inputs, common terminals, and supply pins directly against the device drawing before fabrication.
Can MAX303CPE+ switch bipolar signals?
Yes, the MAX303CPE+ is designed to operate with positive and negative supply rails, allowing bipolar signal routing when the external circuitry remains within the specified limits. The cited operating ranges are 10 V to 30 V for the positive supply and -4.5 V to -20 V for the negative supply. Confirm control-logic levels and absolute maximum ratings in the manufacturer data sheet for the exact design.
Where to buy MAX303CPE+ online?
Use the Request a Quote form on this page to request MAX303CPE+ availability, lead time, and a formal quotation. The request can include the exact MAX303CPE+ ordering code and 16-pin plastic DIP package requirement. This route also helps confirm whether any grade, traceability, or delivery conditions must be attached to the order.
What is the price of MAX303CPE+?
The Request a Quote form on this page is the appropriate way to obtain a current MAX303CPE+ quotation and confirm order quantity and delivery requirements. Pricing depends on quantity, availability, sourcing condition, and any requested traceability or assembly packaging. Submit the exact ordering code MAX303CPE+ with the desired quantities to receive the current commercial terms.
What is the lead time for MAX303CPE+?
The current lead time for MAX303CPE+ should be confirmed through the Request a Quote form on this page. Include the required quantity, target delivery date, acceptable package condition, and any traceability requirements. The manufacturer lists the MAX303 family as production, but individual lot availability and shipment timing can vary by order configuration.
Is MAX303CPE+ currently in production?
The Analog Devices MAX303 product page identifies the MAX303 family as production and links the current product documentation. MAX303CPE+ is therefore treated as an active catalog device. For a new production commitment, confirm the exact suffix, supply availability, and lifecycle status when submitting the purchase request through the Request a Quote form.
When should I choose MAX303CPE+ over another dual SPDT switch?
Choose MAX303CPE+ when the design requires two independent SPDT channels, less than 35 ohms on-resistance, and channel matching guaranteed within 2 ohms in a 16-pin plastic DIP footprint. Its low leakage is also valuable for high-impedance measurement paths. If the circuit can use a surface-mount package, has different logic levels, or does not require the MAX303 family characteristics, compare those requirements before finalizing the choice.
What can replace MAX303CPE+?
The closest documented drop-in candidate is MAX303CPE, which uses the same 16-pin plastic DIP package and the same dual 2:1 SPDT switch architecture. The documented differences concern the ordering suffix and associated product status rather than the switch function or package. A qualified replacement should still be checked for control thresholds, absolute maximum ratings, switching timing, temperature range, and procurement grade.
Is MAX303CPE+ suitable for high-impedance instrumentation?
Yes, MAX303CPE+ is suitable for high-impedance instrumentation when its off-state leakage remains below the measurement budget. Leakage is reported as less than 250 pA at 25°C and less than 6 nA at 85°C. The device also offers less than 35 ohms on-resistance and channel matching within 2 ohms. Guarding, board cleanliness, connector insulation, and temperature stabilization remain important in picoamp-level systems.
What is the best Analog Devices equivalent for MAX303CPE+?
The best Analog Devices candidate identified for a direct package-level comparison is MAX303CPE, which retains the 16-pin plastic DIP format and the same dual 2:1 SPDT function. The MAX301 and MAX305 members of the same family are not drop-in equivalents for MAX303CPE+ because their switch topologies differ. Confirm pin assignments and exact electrical limits in the manufacturer data sheet before substitution.

Datos de referencia de ingeniería para MAX303CPE+ — comparación, orientación de diseño e información de cumplimiento.

Guía de selección

Choose MAX303CPE+ when the design requires two independent SPDT analog switches in a 16-pin plastic DIP package. Its less-than-35-ohm on-resistance, guaranteed 2-ohm channel matching, and low leakage are particularly useful in precision instrumentation and high-impedance measurement systems. MAX303CPE is the closest documented drop-in candidate when the exact plus ordering designation is not required, but its procurement and lead-status requirements should be checked. MAX301CPE and MAX305CPE belong to the same high-speed switch family but should be selected only for SPST or DPST normally open architectures, respectively; they are not functional substitutes for the dual SPDT topology. If a surface-mount footprint is required, verify that a same-pin SPDT device has equivalent logic levels, leakage, supply range, and switching timing before redesigning the board.

Comparación con alternativas

Parámetro Este producto MAX303CPE
Package 16-pin plastic DIP 16-pin plastic DIP
Brand Analog Devices Analog Devices
Switch Type Dual precision high-speed analog switch Dual precision high-speed analog switch
Channel Count 2 channels 2 channels
Switch Configuration 2:1 SPDT per channel 2:1 SPDT per channel
On-Resistance Less than 35 ohm Less than 35 ohm
Channel Matching Within 2 ohm Within 2 ohm
Leakage Current at 25°C Less than 250 pA Less than 250 pA
Lead-Free Ordering Designation MAX303CPE+ MAX303CPE

Diferenciadores clave

  • Two independent SPDT channels in one package (frente a MAX301CPE)
  • Defined channel-to-channel resistance matching (frente a MAX305CPE)
  • Low leakage supports sensitive measurement paths (frente a MAX303CPE)

Notas de diseño

Route the switched signal directly between the MAX303CPE+ terminals and the next active circuit. Keep these traces short, avoid sharing long copper paths with digital control signals, and provide a continuous ground reference beneath the analog routing area. Because the specified on-resistance is below 35 ohms, long PCB traces and connector contacts may contribute more resistance variation than the switch itself, undermining channel-matching calculations.

Include the control-line timing, charge injection, and off-state capacitance in the signal-integrity budget rather than treating the 35-ohm on-resistance as the only error source. The two channels are guaranteed to match within 2 ohms, but dynamic settling can still differ according to external impedance and capacitance. Place any input protection or filtering close enough to preserve the intended signal amplitude and bandwidth.

Do not substitute MAX301 or MAX305 members solely because they share the MAX303 family page. MAX301 uses an SPST, normally open topology, while MAX305 uses a DPST, normally open topology; MAX303 uses two SPDT channels with normally open and normally closed paths. Using the wrong topology can change the pin functions and make the replacement nonfunctional despite a similar package.

Design the supply rails for the full positive and negative operating ranges, including the cited 10 V to 30 V positive range and -4.5 V to -20 V negative range. Check the logic levels that drive the switch controls against the supply arrangement. Decouple each supply rail locally, maintain a common return reference, and ensure no signal excursion exceeds the device absolute maximum ratings.

Información de cumplimiento

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Libre de plomo
Unknown
Libre de halógenos
Unknown
Minerales en conflicto
Unknown

The plus designation is associated with the lead-free ordering variant, but formal RoHS, REACH, halogen-free, conflict-minerals, and automotive-qualification statements require confirmation from the manufacturer documentation.

Datos verificados el: 2026-11-14 — datos verificados y seleccionados por el equipo de ingeniería de componentes de XAIPART

Búsquedas relacionadas

MAX303CPE+ datasheet MAX303CPE+ datasheet pdf MAX303CPE+ pinout MAX303CPE+ equivalent MAX303CPE+ replacement MAX303CPE+ cross reference MAX303CPE+ price MAX303CPE+ stock Analog Devices MAX303CPE+ MAX303CPE+ 16 pin DIP MAX303CPE+ dual SPDT switch MAX303CPE+ vs MAX303CPE MAX303CPE+ instrumentation application MAX303CPE+ on resistance MAX303CPE+ leakage current

Componentes & términos relacionados

Analog Devices Maxim Integrated MAX303CPE+ MAX303CPE MAX303 MAX301 MAX305 precision analog switch analog switch SPDT switch interface IC semiconductor normally open normally closed on-resistance channel matching leakage current bipolar signal routing test and measurement data acquisition 16-pin plastic DIP through-hole package surface-mount alternative high-speed switching
RFQ de presupuesto rápido
Complete los detalles — nuestro equipo de ventas responderá en un plazo de 24 horas
Número de pieza Fabricante Encapsulado QTY Precio objetivo Total
✓
¡Presupuesto enviado!

Responderemos a su correo electrónico en un plazo de 24 horas

1
RFQ enviado
2
Presupuesto recibido
3
Pedido realizado
4
Pago
5
Enviado
6
Entregado
Ver detalles del RFQ