MAX303CPE+ - Dual High-Speed SPDT Analog Switch | Analog Devices
부품 번호: MAX303CPE+ ✓ 활성MAX303CPE+ 개요
An analog switch is a semiconductor device that connects or disects circuit paths under digital control. Unlike a mechanical relay, it can change state rapidly with low control-signal power and without mechanical contact wear. The MAX303 belongs to the interface-IC hierarchy as a precision analog switch and multiplexer. Its matched channels, low leakage, and low on-resistance make it useful where signal integrity must be maintained during measurement, acquisition, or signal-routing operations.
The MAX303CPE+ supports two supply rails, allowing operation from positive to negative voltage when the control input thresholds are compatible with the host logic. Its on-resistance is specified below 35 ohms, and the two channels are guaranteed to match within 2 ohms. These characteristics improve channel-to-channel consistency when the same signal level must be presented to multiple downstream nodes. The device also provides low leakage, reported as below 250 pA at 25°C and below 6 nA at 85°C.
Each channel contains one normally open and one normally closed path. This arrangement allows a signal to be routed to one of two destinations, or provides break-before-make behavior when the control state changes. The MAX303 family is designed for precision, high-speed signal switching, where on-resistance variation, off-state leakage, and channel matching can affect measurement accuracy. The exact switching timing, logic levels, and supply limits should be confirmed in the manufacturer data sheet before final circuit release.
Typical uses include precision test and measurement systems, automated instrumentation, data-acquisition front ends, sample-and-hold circuitry, and bipolar signal-routing networks. In these systems, the MAX303CPE+ can route a sensor or reference signal between measurement paths while keeping insertion resistance and leakage predictable. Its dual-channel architecture reduces component count when two related signals must be selected independently.
PCB layout should preserve short return paths and minimize capacitance around signal and control pins. Keep analog traces away from fast switching clocks and high-current paths, and use a solid ground reference to reduce coupling into the selected channel. Because the part uses a through-hole plastic DIP package, connector and socket accessibility should be checked against mechanical height, cleaning requirements, and assembly-service constraints before releasing the production design.
This product page organizes the MAX303CPE+ electrical characteristics, package information, qualified drop-in alternatives, and practical design guidance for engineers evaluating dual SPDT analog switching. It also distinguishes the lead-free MAX303CPE+ ordering code from the closely related MAX303CPE catalog entry while preserving the distinction between verified drop-in interchangeability and merely similar products.
드롭인 대체품: MAX303CPE+ — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: MAX303CPE+ (동일 폼 팩터 및 풋프린트) — 차이점: On-Resistance, Package.
MAX303CPE
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
MAX303CPE+ 최대 정격 & 전기적 특성
| Device Type | Precision, dual, high-speed analog switch |
| Number of Channels | 2 channels |
| Switch Configuration | 2:1 SPDT per channel |
| On-Resistance | Less than 35 ohm |
| On-Resistance Matching Between Channels | Within 2 ohm |
| Normally Open Paths | 2 paths |
| Normally Closed Paths | 2 paths |
| Leakage Current at 25°C | Less than 250 pA |
| Leakage Current at 85°C | Less than 6 nA |
| Positive Supply Voltage | 10 V to 30 V |
| Negative Supply Voltage | -4.5 V to -20 V |
| 패키지 | 16-pin plastic DIP |
| 실장 유형 | Through-hole |
MAX303CPE+ 16-pin plastic dip 핀 구성 가이드
MAX303CPE+(16-pin plastic dip 패키지)의 핀 구성입니다. 핀 번호, 기능, 연결 다이어그램은 제조사 데이터시트에 정의되어 있습니다. 정확한 풋프린트와 솔더링 지침은 해당 문서를 참조하십시오.
다음에 대한 상세 핀아웃 데이터 없음: MAX303CPE+.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
MAX303CPE+ 적합 용도: 6 애플리케이션s: Precision Test and Measurement Systems, Data Acquisition Front Ends, Bipolar Signal Routing, Sample-and-Hold Signal Selection, Automated Instrumentation, Laboratory Signal Switching.
Precision Test and Measurement Systems
The MAX303CPE+ fits precision test systems that route a source or measurement signal between two instrument paths. Its two independent SPDT channels allow two related selections to be controlled separately, while the less-than-35-ohm on-resistance limit supports relatively low-distortion signal routing. Channel resistance is specified to match within 2 ohms, which helps maintain calibration consistency between the two paths. Leakage below 250 pA at 25°C is also beneficial when the source impedance is high. The practical consideration is to keep connected cables and relay contacts from dominating the leakage budget around the switch.
추천
Data Acquisition Front Ends
The MAX303CPE+ is suitable for data-acquisition front ends that must select between two sensor, reference, or excitation paths. Its two SPDT channels reduce the number of discrete routing elements needed when paired signals require independent selection. The maximum 35-ohm on-resistance and guaranteed 2-ohm channel match provide predictable behavior during calibration, while the low-leakage characteristic supports high-source-impedance sensors. Place the device close to the analog input stage, use short traces, and maintain a quiet ground reference to prevent connector and board contamination from dominating the leakage floor.
추천
Bipolar Signal Routing
The MAX303CPE+ can route bipolar signals because it operates with positive and negative supply rails rather than being limited to a single-polarity domain. The documented rail ranges are 10 V to 30 V and -4.5 V to -20 V. Its low on-resistance limits the voltage-drop burden when the switched source impedance is not negligible, while the normally open and normally closed paths support both source selection and signal isolation. The circuit must maintain each signal terminal inside the absolute maximum limits, including during control-state transitions.
추천
Sample-and-Hold Signal Selection
The MAX303CPE+ is appropriate for sample-and-hold front ends that need to select one of two candidate signals before conversion or storage. Two independently switched SPDT channels can handle complementary or parallel selections, and the less-than-35-ohm on-resistance helps limit acquisition-voltage error relative to higher-impedance switches. The 2-ohm channel-match guarantee improves consistency when both channels feed sensitive downstream stages. Pay particular attention to switching transients and control timing because acquisition accuracy can also be affected by charge injection and hold-settling behavior.
추천
Automated Instrumentation
The MAX303CPE+ supports automated instrumentation that repeatedly connects a common source to one of two destinations. The dual SPDT arrangement is useful in scanner, matrix, and programmable-measurement systems where route isolation and repeatable resistance matter. The specified on-resistance ceiling of 35 ohms and channel matching within 2 ohms provide useful bounds for impedance and calibration calculations. For long switch lifetimes, choose connector and socket components that do not introduce a larger contact-resistance variation than the IC itself, and keep sensitive routes physically separated from actuator and relay wiring.
추천
Laboratory Signal Switching
The MAX303CPE+ is well suited to laboratory signal switching where a single input must be selected among two paths and leakage can affect small-signal measurements. Leakage below 250 pA at 25°C and below 6 nA at 85°C provides a defined starting point for error budgeting, while the sub-35-ohm resistance limit reduces insertion loss for moderate source impedances. Use short, guarded analog traces and clean connectors, particularly when working with femtoamp- or picoamp-level leakage requirements. Temperature rise can increase leakage, so account for warm operating conditions rather than relying only on the 25°C figure.
추천
추천 제품 요약
엔지니어링 참조 데이터: MAX303CPE+ — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | MAX303CPE |
|---|---|---|
| Package | 16-pin plastic DIP | 16-pin plastic DIP |
| Brand | Analog Devices | Analog Devices |
| Switch Type | Dual precision high-speed analog switch | Dual precision high-speed analog switch |
| Channel Count | 2 channels | 2 channels |
| Switch Configuration | 2:1 SPDT per channel | 2:1 SPDT per channel |
| On-Resistance | Less than 35 ohm | Less than 35 ohm |
| Channel Matching | Within 2 ohm | Within 2 ohm |
| Leakage Current at 25°C | Less than 250 pA | Less than 250 pA |
| Lead-Free Ordering Designation | MAX303CPE+ | MAX303CPE |
주요 차별점
- Two independent SPDT channels in one package (vs MAX301CPE)
- Defined channel-to-channel resistance matching (vs MAX305CPE)
- Low leakage supports sensitive measurement paths (vs MAX303CPE)
설계 노트
Route the switched signal directly between the MAX303CPE+ terminals and the next active circuit. Keep these traces short, avoid sharing long copper paths with digital control signals, and provide a continuous ground reference beneath the analog routing area. Because the specified on-resistance is below 35 ohms, long PCB traces and connector contacts may contribute more resistance variation than the switch itself, undermining channel-matching calculations.
Include the control-line timing, charge injection, and off-state capacitance in the signal-integrity budget rather than treating the 35-ohm on-resistance as the only error source. The two channels are guaranteed to match within 2 ohms, but dynamic settling can still differ according to external impedance and capacitance. Place any input protection or filtering close enough to preserve the intended signal amplitude and bandwidth.
Do not substitute MAX301 or MAX305 members solely because they share the MAX303 family page. MAX301 uses an SPST, normally open topology, while MAX305 uses a DPST, normally open topology; MAX303 uses two SPDT channels with normally open and normally closed paths. Using the wrong topology can change the pin functions and make the replacement nonfunctional despite a similar package.
Design the supply rails for the full positive and negative operating ranges, including the cited 10 V to 30 V positive range and -4.5 V to -20 V negative range. Check the logic levels that drive the switch controls against the supply arrangement. Decouple each supply rail locally, maintain a common return reference, and ensure no signal excursion exceeds the device absolute maximum ratings.
규정 준수 정보
The plus designation is associated with the lead-free ordering variant, but formal RoHS, REACH, halogen-free, conflict-minerals, and automotive-qualification statements require confirmation from the manufacturer documentation.