MAX3078EESA+ - 3.3V RS-485/RS-422 ESD Transceiver
N.º de pieza: MAX3078EESA+ ✓ Activo| Cant. | Precio unitario | Total |
|---|---|---|
| 1 | $4.65 | $4,65 |
| 10 | $4.65 | $46,50 |
| 100 | $4.65 | $465,00 |
| 500 | $4.65 | $2.325,00 |
| 1.000 | $4.65 | $4.650,00 |
MAX3078EESA+ Descripción general
An RS-485/RS-422 transceiver is an interface IC that converts between logic-level signals and balanced differential line signals. In the RS-485 mode, the differential bus supports communication between multiple nodes when the system is properly terminated and biased. In RS-422 mode, the device provides a balanced driver and receiver for point-to-point links. The MAX3078EESA+ is part of the broader interface-IC hierarchy and supports both standards in one compact device.
Key verified features include ±15kV ESD protection on the bus-facing pins, fail-safe receiver operation that guarantees a logic-high output when receiver inputs are open or shorted, and hot-swap capability designed to eliminate false bus transitions during power-up or hot insertion. The device operates from a 2.97V to 3.63V supply range and contains one driver and one receiver. Manufacturer data describes a supply current of 800µA when unloaded or when fully loaded with the drivers disabled.
The MAX3078EESA+ is suitable for industrial controllers, instrumentation links, data acquisition systems, building automation equipment, and embedded communications networks. Its 3.3V supply operation aligns with modern low-voltage digital systems, while the ESD protection and fail-safe circuitry help improve interface reliability in electrically noisy environments. The 8-pin SOIC package supports conventional surface-mount PCB assembly.
When laying out a MAX3078EESA+ circuit, keep the bus traces short and controlled, provide the required termination and fail-safe bias network at the appropriate bus locations, and route high-energy transient paths away from sensitive logic. Verify the receiver and driver enable polarity against the system controller because the available control and interface details are not fully specified in the provided verified excerpts.
This page combines the verified manufacturer and distributor descriptions with practical RS-485/RS-422 design guidance, package information, selection criteria, and engineering-oriented caveats. Unavailable detailed electrical limits are explicitly marked rather than inferred, allowing designers to validate them against the complete manufacturer datasheet before release to production.
Alternativas directas para MAX3078EESA+ — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con MAX3078EESA+ (mismo factor de forma y huella) — difiere en Package, ESD Protection, Fail-Safe Receiver, RoHS Status, Supply Voltage Range.
Herramienta de comparación rápida — seleccione piezas alternativas para compararlas lado a lado:
MAX3078EESA+T
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
MAX3078EASA+
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
MAX3078EESA
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
MAX3076EESD+T
✅ Sustitución directa✓ En stock
Consulte el precio
Ver hoja de datos →MAX3075EESA+
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
MAX3078EESA+ Especificaciones
| Product Type | RS-485/RS-422 transceiver |
| Supply Voltage Range | 2.97V to 3.63V |
| Driver Count | 1 |
| Receiver Count | 1 |
| Interface Standards | RS-485 and RS-422 |
| ESD Protection | ±15kV |
| Fail-Safe Receiver | Logic-high output when receiver inputs are open or shorted |
| Hot-Swap Capability | Supported |
| Unloaded Supply Current | 800µA |
| Supply Current With Drivers Disabled | 800µA when fully loaded |
| Encapsulado | 8-pin SOIC |
| Tipo de montaje | Surface mount |
| DigiKey Listing Package | 8-SOIC |
| Manufacturer Product Status | PRODUCTION |
| Manufacturer Data Sheet Revision | Rev. 5 |
Guía de configuración de pines de MAX3078EESA+ 8-soic
Configuración de pines para MAX3078EESA+ (encapsulado 8-soic). La numeración de pines, las funciones y los diagramas de conexión se definen en la hoja de datos del fabricante. Consúltela para conocer el footprint exacto y las directrices de soldadura.
No hay datos detallados de patillaje disponibles para MAX3078EESA+.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
MAX3078EESA+ es adecuado para 6 aplicacións: Industrial RS-485 Control Networks, Building Automation Interfaces, Data Acquisition and Instrumentation, Embedded Communication Ports, Remote Sensor and Actuator Links, Low-Voltage RS-422 Point-to-Point Links.
Industrial RS-485 Control Networks
The MAX3078EESA+ fits industrial control and sensor networks that use balanced differential RS-485 signaling at a 2.97V-to-3.63V supply. Its one-driver, one-receiver arrangement supports a compact node interface, while ±15kV ESD protection and fail-safe receiver behavior help improve robustness against cable-borne transients and wiring faults. The circuit should use a defined bus topology, appropriate termination, and a bias strategy that keeps the receiver output valid when the bus is idle.
Recomendado
Building Automation Interfaces
Use the MAX3078EESA+ in building-automation equipment where controllers communicate with sensors, actuators, and distributed I/O over RS-485. The 3.3V supply operation can simplify integration with low-voltage embedded controllers, and the verified hot-swap capability helps reduce false transitions during power-up or hot insertion. Because automation cables can be long and exposed to nearby switching equipment, controlled routing, grounding, termination, and verified ESD behavior are important design requirements.
Recomendado
Data Acquisition and Instrumentation
The MAX3078EESA+ is appropriate for measurement and data-acquisition equipment that needs a compact differential bus interface between an embedded controller and remote instrumentation. Fail-safe receiver operation is useful when the bus may be disconnected or shorted, while the one-driver, one-receiver arrangement provides a straightforward node connection. Confirm signal levels, slew behavior, and timing against the complete data sheet before defining the maximum cable length and data rate.
Recomendado
Embedded Communication Ports
The MAX3078EESA+ can provide a low-voltage balanced communication port for embedded control boards. Its 2.97V-to-3.63V operating range aligns with 3.3V digital systems, and the 8-pin SOIC package simplifies surface-mount assembly and PCB footprint planning. In a new design, verify the exact driver-enable and receiver-enable pin functions, power-up behavior, and bus idle behavior from the manufacturer pinout rather than relying on the package name alone.
Recomendado
Remote Sensor and Actuator Links
For remote sensor and actuator networks, the MAX3078EESA+ offers a compact way to connect a controller to balanced field-bus wiring. Its verified ESD protection is relevant when field wiring connects to externally accessible equipment, and the fail-safe receiver provides a defined high state for open or shorted receiver inputs. The application must still validate cable length, topology, grounding, protection placement, and communication timing against the complete manufacturer specification.
Recomendado
Low-Voltage RS-422 Point-to-Point Links
The MAX3078EESA+ can also serve RS-422 point-to-point links because the verified device description identifies both RS-485 and RS-422 support. The 3.3V supply range is useful for compact industrial and embedded systems, and the one-driver, one-receiver configuration provides a balanced link without requiring a multi-drop bus arrangement. Confirm the exact receiver thresholds, driver output capability, and enable controls in the complete data sheet before setting baud rate and cable length.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para MAX3078EESA+ — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | MAX3078EESA+T | MAX3078EASA+ | MAX3076EESD+ | MAX3075EESA+ |
|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 8-pin SOIC | 8-SOIC | 8-pin SOIC | 14-pin NSOIC | 8-pin SOIC |
Diferenciadores clave
- 3.3V-class supply operation (frente a MAX3076EESD+)
- Compact 8-pin SOIC implementation (frente a MAX3076EESD+)
- Verified fail-safe and hot-swap features (frente a MAX3075EESA+)
Notas de diseño
Route the RS-485/RS-422 differential pair as a closely coupled pair with substantially equal length and geometry, and connect the receiver and transceiver ground to the system ground with a low-impedance path. Avoid crossing the bus with switching traces or routing it beneath noisy power stages. Because the provided verified data does not specify a complete trace-impedance or spacing recommendation, confirm the applicable values from the complete MAX3078E data sheet and the system’s cable and grounding requirements.
Do not assume that every related MAX3078E suffix is automatically interchangeable. The verified results show MAX3078EESA+, MAX3078EESA+T, MAX3078EASA+, MAX3076EESD+, and MAX3075EESA+, but the excerpts do not provide complete pin assignments, enable polarity, or electrical limits for each variant. Confirm package dimensions, pin names, supply limits, receiver thresholds, driver enable behavior, and ESD configuration before approving a substitution.
Place termination and fail-safe bias components at the locations required by the selected RS-485 topology rather than scattering them across the bus. For RS-422 point-to-point links, use the termination arrangement specified by the complete system interface requirements. Keep the bus-side protection and transceiver ground return paths short, and validate the implementation with cable-length, baud-rate, common-mode, and hot-plug tests.
Información de cumplimiento
The provided verified excerpts identify the manufacturer, product status, interface function, ESD protection, package, and supply information but do not state RoHS, REACH, lead-free, halogen-free, conflict-minerals, or automotive qualification status.