MAX3221EIDBR - 250kbps 3V-5.5V RS-232 Transceiver | TI (Tape & Reel)
N.º de pieza: MAX3221EIDBR ✓ ActivoMAX3221EIDBR Descripción general
An RS-232 transceiver is an interface IC that converts logic-level signals between a host controller and a serial port. The MAX3221E combines a differential line driver, receiver, dual charge-pump circuit, and automatic signal generation in one package. It occupies the interface ICs level within the broader communications and industrial-control hierarchy, where reliable voltage translation, electrostatic-discharge protection, and economical PCB integration are important.
The device provides one full-duplex RS-232 channel with a maximum data rate of 250kbps. Its single 3V to 5.5V supply operation allows use with both 3.3V and 5V systems. The integrated charge pump produces the bipolar voltage levels required by RS-232 while reducing the number of external components to four small capacitors. IEC 61000-4-2 protection on the serial-port connection pins adds protection where cables enter an enclosure.
The MAX3221E implements one driver and one receiver with a dedicated receiver-enable function. It provides the electrical interface between an asynchronous communication controller and an RS-232 connector while satisfying TIA/EIA-232-F requirements. This architecture suits point-to-point links that do not require multiple RS-232 channels, such as service-console, configuration-port, industrial-controller, and legacy peripheral connections.
Typical applications include single-port RS-232 adapters, programmable logic controller service interfaces, industrial control equipment, test fixtures, and embedded systems that retain a legacy serial connector. The 16-pin SSOP package supports compact, surface-mount PCB construction, while the 250kbps rate is suitable for moderate-speed asynchronous data transfer rather than high-bandwidth protocols.
Designers should follow the manufacturer’s recommended capacitor values and placement guidance for the charge-pump circuit. Keep the external capacitors close to their designated pins, route the RS-232 connector-side nets away from sensitive logic, and use a suitable protection network when cables extend beyond the protected board boundary. Verify that the host voltage levels and connector pin assignment match the selected logic family.
This product page combines the MAX3221EIDBR electrical characteristics, package details, available drop-in alternatives, comparison parameters, and application-specific design guidance. It is intended to accelerate component selection, PCB planning, and RS-232 interface qualification without requiring the reader to reconstruct the design trade-offs from separate listings.
Alternativas directas para MAX3221EIDBR — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con MAX3221EIDBR (mismo factor de forma y huella) — difiere en Package, Product Type, Number of Drivers, Number of Receivers, Supply Voltage Range.
MAX3221CDBR
✅ Sustitución directa ⚠️ Especificaciones sin verificarConsulte el precio
Ver hoja de datos →MAX3221IDBR
✅ Sustitución directaConsulte el precio
Ver hoja de datos →MAX3221ECDBRG4
✅ Sustitución directaConsulte el precio
Ver hoja de datos →MAX3221EIDBR Especificaciones
| Product Type | RS-232 line driver and receiver transceiver |
| Number of Drivers | 1 |
| Number of Receivers | 1 |
| Velocidad de datos | 250kbps |
| Supply Voltage Range | 3V to 5.5V |
| Interface Standard | TIA/EIA-232-F |
| ESD Protection Standard | IEC 61000-4-2 |
| ESD Protection Voltage | ±15kV |
| Charge Pumps | 2 |
| External Charge-Pump Capacitors | 4 |
| Encapsulado | 16-SSOP (0.209 inch, 5.30mm width) |
| Tipo de montaje | Surface mount |
| Transceiver Type | 1/1 full-duplex RS-232 transceiver |
Guía de configuración de pines de MAX3221EIDBR 16-ssop (0.209 inch, 5.30mm width)
Configuración de pines para MAX3221EIDBR (encapsulado 16-ssop (0.209 inch, 5.30mm width)). La numeración de pines, las funciones y los diagramas de conexión se definen en la hoja de datos del fabricante. Consúltela para conocer el footprint exacto y las directrices de soldadura.
No hay datos detallados de patillaje disponibles para MAX3221EIDBR.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
MAX3221EIDBR es adecuado para 6 aplicacións: Industrial Configuration Port, RS-232 Service Console, Legacy Peripheral Adapter, Test and Measurement Fixture, Security and Access Controller, Programmable Controller Communication.
Industrial Configuration Port
The MAX3221EIDBR fits a single industrial equipment configuration port that must communicate with a laptop or service controller over RS-232. Its 3V to 5.5V supply range supports both 3.3V and 5V embedded controllers, while the 250kbps rate is appropriate for command exchange, firmware transfer, and diagnostic records. The ±15kV IEC 61000-4-2 protection on the connector-side pins improves robustness when the port is accessed by field technicians. Designers should route the protected RS-232 traces directly toward the connector and maintain the recommended charge-pump capacitor placement.
Recomendado
RS-232 Service Console
The MAX3221EIDBR is appropriate for a service-console link between an embedded controller and an RS-232 diagnostic adapter. One driver and one receiver are sufficient for a full-duplex point-to-point connection, and the 250kbps data rate supports console commands, diagnostic logs, and configuration transactions. Operating from a single 3V to 5.5V rail simplifies interface design around contemporary embedded processors. The enhanced E-version ESD protection is especially useful where technicians connect external equipment directly to a field-accessible port.
Recomendado
Legacy Peripheral Adapter
The MAX3221EIDBR can bridge a modern low-voltage controller and a legacy RS-232 peripheral without requiring a separate negative power rail. Its integrated dual charge pump generates the required bipolar line levels, while four external capacitors support the charge-pump circuit. The 16-pin SSOP package keeps the interface compact on densely populated controller boards. For an exposed legacy connector, the ±15kV IEC 61000-4-2 rating provides additional electrostatic-disense protection compared with a basic MAX3221 transceiver.
Recomendado
Test and Measurement Fixture
The MAX3221EIDBR supports RS-232 control and logging functions in a test fixture where a computer communicates with instrumentation over a single serial channel. Its 250kbps maximum rate is more than adequate for command traffic and measured-data transfer, while the 3V to 5.5V supply range allows direct operation from common laboratory and embedded test-control rails. The protected connector-side pins add useful robustness when test leads are repeatedly attached. Keep the charge-pump components close to the device and separate the interface from sensitive analog measurement circuitry.
Recomendado
Security and Access Controller
The MAX3221EIDBR is suitable for a security controller that retains an RS-232 path for configuration, event logging, or integration with a higher-level access system. The single-driver, single-receiver arrangement supports full-duplex communication with a host while consuming little board space in a 16-pin SSOP package. Its single 3V to 5.5V supply simplifies connection to the controller’s digital rail, and the enhanced ESD protection improves interface resilience at an externally accessible port. Firmware updates should use a controlled protocol because RS-232 does not provide modern authentication or encryption.
Recomendado
Programmable Controller Communication
The MAX3221EIDBR connects a programmable controller to an RS-232 network or peripheral when one full-duplex channel is sufficient. The 250kbps rate supports telemetry, command exchange, and status polling, while the 3V to 5.5V operating range accommodates common embedded supply voltages. The target’s single-supply charge-pump design avoids a discrete negative rail and reduces external component count. For installations with severe conducted noise or long exposed cables, retain the connector-side ESD protection and validate signal integrity across the complete cable and grounding system.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para MAX3221EIDBR — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | MAX3221CDBR | MAX3221IDBR | MAX3221ECDB |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 16-SSOP (DB) | 16-SSOP (DB) | 16-SSOP (DB) | 16-SSOP (DB) |
| Transceiver Configuration | 1 driver / 1 receiver | 1 driver / 1 receiver | 1 driver / 1 receiver | 1 driver / 1 receiver |
| Data Rate | 250kbps | 250kbps | 250kbps | 250kbps |
| Supply Voltage Range | 3V to 5.5V | 3V to 5.5V | 3V to 5.5V | 3V to 5.5V |
Diferenciadores clave
- Enhanced connector-side ESD protection (frente a MAX3221IDBR)
- Single-supply operation across common logic rails (frente a MAX3221CDBR)
- General-purpose interface versus automotive qualification (frente a MAX3221ECDB)
Notas de diseño
Place the four charge-pump capacitors close to their designated MAX3221EIDBR pins and keep the associated traces short. Follow the Texas Instruments MAX3221E application diagram for capacitance values and route the charge-pump nets away from the RS-232 connector-side nets. Short charge-pump loops reduce radiated noise and help maintain stable line levels during data transmission.
Do not treat a matching 16-SSOP footprint as proof of drop-in compatibility. Before substituting MAX3221CDBR, MAX3221IDBR, or MAX3221ECDB, compare pin assignments, supply limits, receiver-enable behavior, ESD requirements, temperature range, and qualification status. The MAX3221EIDBR specifically provides ±15kV IEC 61000-4-2 protection on the RS-232 pins, so systems that rely on that rating need protection added if the replacement does not provide it.
Route the connector-side RS-232 signals as a compact interface directly toward the protection circuitry and connector, while keeping them separated from clocks, sensors, and high-impedance analog inputs. Connect the device ground and charge-pump capacitor ground to a low-impedance ground plane. This layout reduces susceptibility to ground bounce and prevents the interface’s switching activity from coupling into sensitive signal paths.
Treat the RS-232 cable as an external antenna and keep it away from internal high-impedance nodes. Use the integrated connector-side ESD protection as one part of the protection strategy rather than the only safeguard. For long or industrial cables, evaluate whether additional surge, common-mode, or cable-shield measures are required; the IEC 61000-4-2 rating addresses electrostatic discharge rather than every industrial transient source.
Información de cumplimiento
The manufacturer information identifies IEC 61000-4-2 ESD protection and TIA/EIA-232-F interface compliance. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation for the exact ordering code.