Texas Instruments

MAX3232ECPWR - Dual RS-232 Transceiver | Texas Instruments (Tape & Reel)

N.º de pieza: MAX3232ECPWR ✓ Activo
3 V to 5.5 V Vdss 16-pin TSSOP Package
MOQ: 1 |

MAX3232ECPWR Descripción general

The Texas Instruments MAX3232ECPWR is a dual-channel RS-232 line transceiver operating from a single 3 V to 5.5 V supply, supporting signal rates up to 250 kbit/s and providing ±15 kV IEC ESD protection. The device combines two line drivers, two line receivers, and a dual charge-pump circuit in a 16-pin TSSOP package.

An RS-232 transceiver is an interface IC that converts logic-level signals from a processor or controller into RS-232 voltage levels, while converting received RS-232 signals back into logic-compatible levels. Within the hierarchy of interface ICs, serial transceivers connect digital controllers to communication ports using the TIA/EIA-232-F electrical standard. The MAX3232ECPWR uses an on-chip charge pump to generate positive and negative RS-232 voltages from one low-voltage supply.

The device accepts supply voltages from 3 V to 5.5 V and operates at data-signaling rates up to 250 kbit/s. Its two transmitters and two receivers support full-duplex serial links, while driver output slew rate is limited to 30 V/µs. Pin-to-pin ESD protection rated at ±15 kV improves system robustness when cables are connected or disconnected.

The MAX3232ECPWR is the commercial-temperature version of the MAX3232E family, specified for 0 °C to 70 °C. It is packaged in a 16-pin gull-wing TSSOP with a 4.4 mm lead pitch. Four external charge-pump capacitors are required, allowing the interface to operate from a single 3 V or 5 V rail without a separate negative power supply.

Typical uses include industrial serial adapters, data-acquisition equipment, point-of-sale terminals, laboratory instruments, and service-console links. The device is appropriate when a controller needs an RS-232 port but cannot generate the positive and negative voltages required by legacy RS-232 drivers directly.

Place the four charge-pump capacitors close to their associated pins and keep the exposed supply and ground paths short. Keep the RS-232 connector interface physically separated from sensitive analog or high-speed digital routing, and provide appropriate board-level protection when exposed cables exceed the device's rated ESD withstand.

This product page combines electrical specifications, package and pin information, drop-in replacement analysis, application guidance, and design notes for engineers evaluating the MAX3232ECPWR in 3 V and 5 V RS-232 interfaces.

Alternativas directas para MAX3232ECPWR — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.

Variantes de esta serie

Modelos de la misma serie compatibles directamente con MAX3232ECPWR (mismo factor de forma y huella) — difiere en Product Type, Package, Supply Voltage Range, Channel Configuration, ESD Protection.

Texas Instruments
Product Type: Dual RS-232 line driver/receiver transceiver
Package: 16-pin TSSOP (PW)
Channel Configuration: 2/2 full RS-232 transceiver
Comparar con MAX3232ECPWR →
Texas Instruments
Product Type: Dual RS-232 line driver and receiver
Supply Voltage Range: 3V to 5.5V
Channel Configuration: 2/2 transceiver
Comparar con MAX3232ECPWR →

MAX3232CPWR

✅ Sustitución directa ⚠️ Especificaciones sin verificar
Texas Instruments
📦 16-TSSOP
Dual RS-232 line driver/receiver transceiver · 3 V to 5.5 V · 250 kbit/s · 2 · 2 · ±15 kV · 300 µA · 0.1 µF

Consulte el precio

Ver hoja de datos →

MAX3232IPW

✅ Sustitución directa ⚠️ Especificaciones sin verificar
Texas Instruments
📦 16-TSSOP
Dual RS-232 line driver and receiver · 2 channels · 2 channels · 3V to 5.5V · 250kbit/s · ±15kV · 5V logic · 0.1µF

Consulte el precio

Ver hoja de datos →

MAX3232EWP

✅ Sustitución directa ⚠️ Especificaciones sin verificar
📦 16-TSSOP
Uses the same MAX3232E 250 kbit/s interface and ±15 kV IEC ESD protection, with the commercial ordering option differing by the exact package suffix.

📋 Alternativa de referencia (no en el catálogo)

MAX3232EA

✅ Sustitución directa ⚠️ Especificaciones sin verificar
📦 16-TSSOP
Shares the 250 kbit/s dual RS-232 interface with MAX3232ECPWR, while the ordering suffix determines the commercial temperature and package configuration.

📋 Alternativa de referencia (no en el catálogo)

ST3232CTR

✅ Sustitución directa
📦 16-TSSOP
Provides the same 3 V to 5.5 V dual RS-232 interface and 250 kbit/s operation with matching terminals, while ESD, temperature, and lifecycle details require separate review.

📋 Alternativa de referencia (no en el catálogo)

MAX3232ECPWR Especificaciones

Product Type Dual RS-232 line transceiver
Supply Voltage Range 3 V to 5.5 V
Number of Line Drivers 2 channels
Number of Line Receivers 2 channels
Maximum Data Signaling Rate 250 kbit/s
Maximum Driver Output Slew Rate 30 V/µs
IEC ESD Protection ±15 kV
RS-232 Compliance TIA/EIA-232-F
Charge Pump Dual charge-pump circuit
External Charge-Pump Capacitors 4 capacitors
Rango de temperatura de funcionamiento 0 °C to 70 °C
Temperature Grade Commercial
Encapsulado 16-pin TSSOP
Lead Pitch 4.4 mm
Recuento de pines 16 pins
Terminal Form Gull wing
Package Shape Rectangular

Configuración de pines de MAX3232ECPWR

TSSOP-16 Package Pinout Diagram TSSOP-16 4.4x5mm, P0.65mm, JEDEC MO-153. 1 16 2 15 3 14 4 13 5 12 6 11 7 10 8 9 TSSOP-16
Pin 1 R1IN — Receiver 1 input
Pin 2 R1OUT — Receiver 1 output
Pin 3 R2IN — Receiver 2 input
Pin 4 R2OUT — Receiver 2 output
Pin 5 GND — Ground connection
Pin 6 V+ — Positive charge-pump output
Pin 7 C2+ — Charge-pump capacitor 2 positive terminal
Pin 8 C1+ — Charge-pump capacitor 1 positive terminal
Pin 9 C1- — Charge-pump capacitor 1 negative terminal
Pin 10 C2- — Charge-pump capacitor 2 negative terminal
Pin 11 V- — Negative charge-pump output
Pin 12 T1IN — Transmitter 1 logic input
Pin 13 T2IN — Transmitter 2 logic input
Pin 14 T1OUT — Transmitter 1 RS-232 output
Pin 15 T2OUT — Transmitter 2 RS-232 output
Pin 16 VCC — Device supply input

Aplicaciones típicas

MAX3232ECPWR es adecuado para 6 aplicacións: Industrial Serial Port Interface, Point-of-Sale Terminal, Data Acquisition Equipment, Laboratory Instrument Console, Service and Configuration Port, Embedded System Serial Adapter.

🏭

Industrial Serial Port Interface

The MAX3232ECPWR is suitable for industrial controllers that require a legacy RS-232 port but operate from a 3.3 V or 5 V logic rail. Its dual charge-pump circuit generates the positive and negative voltages needed by the RS-232 interface from one 3 V to 5.5 V supply, avoiding a separate negative rail. The two transmitters and two receivers support full-duplex communication at rates up to 250 kbit/s. The ±15 kV IEC ESD protection is valuable when the connector is accessible to service personnel or connected equipment. Place the four charge-pump capacitors close to pins 7 through 10 and route the exposed connector interface away from sensitive circuitry.

🖥️

Point-of-Sale Terminal

Point-of-sale equipment can use the MAX3232ECPWR to connect a controller to a receipt printer, scanner, or service terminal through RS-232. The 250 kbit/s maximum signaling rate covers common serial-port traffic while the controlled 30 V/µs driver slew rate supports compliant RS-232 transitions. Operation from a single 3 V to 5.5 V rail simplifies system power design, and the integrated charge pump removes the need for a discrete negative supply generator. Because peripherals may be connected by user-accessible cables, the ±15 kV IEC ESD protection improves connector-side robustness. Maintain a low-impedance ground path between the transceiver and connector and consider additional surge protection for installations exposed to severe transients.

📊

Data Acquisition Equipment

The MAX3232ECPWR provides a compact interface between a data-acquisition controller and an RS-232-compatible instrument. Its 250 kbit/s capability is appropriate for configuration commands, measurement results, and status reporting in many laboratory and industrial systems. The 16-pin TSSOP package preserves board area while the single 3 V to 5.5 V supply operation simplifies rail planning around modern processors and FPGAs. The ±15 kV IEC ESD rating helps protect the interface when instrument cables are routinely reconnected. Keep the four external charge-pump capacitors near the IC and provide a quiet ground connection, because cable transients and ground potential differences can otherwise affect communication reliability.

🔧

Laboratory Instrument Console

MAX3232ECPWR can serve as the host-side RS-232 interface in laboratory instruments that retain legacy serial consoles. A computer or embedded controller communicates through the two receiver channels, while the two driver channels support bidirectional command and data transfer. The device's 250 kbit/s maximum data rate is suitable for terminal sessions, configuration files, and instrument status messages. Running from a 3 V to 5.5 V supply permits use with both legacy 5 V controllers and modern 3.3 V systems. The integrated charge pump requires only four external capacitors and no separate negative supply, reducing board complexity. The commercial 0 °C to 70 °C rating should be checked against the instrument's internal temperature environment.

🔌

Service and Configuration Port

The MAX3232ECPWR is well suited to equipment that retains a service or configuration connector for diagnostics, firmware loading, and parameter adjustment. Its bidirectional 250 kbit/s interface supports both command transmission and status reception. The ±15 kV IEC ESD protection is particularly relevant to service ports because technicians frequently connect and disconnect cables. A single 3 V to 5.5 V supply allows the transceiver to operate directly alongside embedded processors without an additional negative-voltage rail. Designers should keep the RS-232 trace away from clocks, ADC inputs, and switching-converter power nodes, and should verify that the external connector does not introduce ground offsets beyond the device interface tolerances.

🧩

Embedded System Serial Adapter

An embedded controller can use the MAX3232ECPWR to add a conventional RS-232 port to a system built around a 3.3 V processor. The device converts logic-level transmit inputs into RS-232 levels and converts received signals back to logic-compatible outputs, while the internal charge pump supplies the required positive and negative voltages. Its 16-pin TSSOP footprint supports compact single-board designs, and 250 kbit/s operation covers legacy printer, modem, and instrument-control links. Four charge-pump capacitors are required for operation. Place them close to the associated pins, minimize loop area around the charge-pump nodes, and preserve an uninterrupted ground connection between the IC, connector shield, and chassis or enclosure grounding strategy.

What is the MAX3232ECPWR?
The MAX3232ECPWR is a dual-channel RS-232 transceiver with two line drivers, two line receivers, and an integrated dual charge-pump circuit. According to the Texas Instruments product page, it operates from one 3 V to 5.5 V supply, supports data rates up to 250 kbit/s, and includes ±15 kV IEC ESD protection. It is intended to connect a digital controller to a TIA/EIA-232-F serial port without requiring a separate negative supply.
What are the key specifications of MAX3232ECPWR that engineers should know?
The MAX3232ECPWR combines a 3 V to 5.5 V supply range, two drivers, two receivers, and a maximum signaling rate of 250 kbit/s. Texas Instruments specifies ±15 kV IEC ESD protection, a maximum driver slew rate of 30 V/µs, and a commercial operating range of 0 °C to 70 °C. The device uses four external charge-pump capacitors and is offered in a 16-pin TSSOP package with 4.4 mm lead pitch.
Where can I download the MAX3232ECPWR datasheet PDF?
The official MAX3232ECPWR technical information is available from the Texas Instruments MAX3232E product page and datasheet link. The manufacturer documentation contains the electrical characteristics, charge-pump capacitor requirements, pin descriptions, and application information for the MAX3232E family. Use the manufacturer PDF for final PCB, timing, and ESD decisions because the commercial-temperature ordering code is part of the same MAX3232E technical documentation.
Where can I find the MAX3232ECPWR pinout?
The MAX3232ECPWR uses a 16-pin TSSOP layout with pins 1 through 4 assigned to the two receiver inputs and outputs, pins 12 and 13 assigned to transmitter inputs, and pins 14 and 15 assigned to transmitter outputs. Pins 6 and 11 provide the charge-pump supply rails, while pins 7 through 10 connect to the four external capacitors. Use the pin-description table in the manufacturer datasheet when assigning PCB tracks.
Can MAX3232ECPWR operate from a 3.3 V supply?
Yes. The MAX3232ECPWR is specified for a single 3 V to 5.5 V supply, making it suitable for 3.3 V systems. Its internal charge pump generates the positive and negative voltages required for RS-232 transmission, while the logic-side interface operates from the same supply. Four external charge-pump capacitors are still required, and the selected capacitor values should follow the manufacturer application guidance.
What is the maximum data rate of MAX3232ECPWR?
The MAX3232ECPWR supports data-signaling rates up to 250 kbit/s according to the Texas Instruments product page. This is adequate for many legacy serial-port, industrial-control, and point-of-sale applications. The maximum driver output slew rate is 30 V/µs, a controlled edge rate that helps satisfy RS-232 signal-shape requirements. The complete system should still be checked for connector, cable, and protocol timing constraints.
What does the E in MAX3232ECPWR provide?
The MAX3232E family provides enhanced ESD protection rated at ±15 kV on the serial-port connection pins. Compared with the earlier MAX3232 family, the E version is identified by Texas Instruments as an improved direct replacement for MAX3232 designs. The MAX3232ECPWR also has the same single-supply charge-pump architecture, 250 kbit/s data rate, and 16-pin TSSOP implementation as the standard MAX3232E.
Is MAX3232ECPWR suitable for industrial equipment?
MAX3232ECPWR can be used in commercial-temperature equipment operating from 0 °C to 70 °C. It provides ±15 kV IEC ESD protection, which is valuable in systems with externally accessible serial connectors. Industrial systems that require operation below 0 °C or above 70 °C should select an appropriately temperature-rated variant and confirm that it retains the same pin arrangement and required electrical performance.
What is the best drop-in replacement for MAX3232ECPWR?
The MAX3232CPW is a close same-family drop-in option in the same 16-pin TSSOP footprint, while the MAX3232EWP provides the enhanced MAX3232E function in the same package. Neither substitution should be assumed without reviewing the exact ordering code. Confirm supply range, operating temperature, ESD rating, charge-pump capacitor values, and lifecycle requirements in the manufacturer datasheet before releasing a replacement into production.
Can ST3232CTR replace MAX3232ECPWR?
ST3232CTR is identified as a direct replacement for MAX3232ECPWR in the cross-reference results, with consistent terminals, package, and principal RS-232 functions. Before substituting it, verify the 16-pin TSSOP footprint, 3 V to 5.5 V supply range, 250 kbit/s data rate, ESD rating, temperature range, and charge-pump capacitor configuration. Compatibility of the basic interface does not automatically guarantee identical EMC or system-level qualification.
MAX3232ECPWR vs MAX3232CPW: which is better for a new design?
MAX3232ECPWR is preferable when the system needs the enhanced ±15 kV IEC ESD protection associated with the MAX3232E family. MAX3232CPW retains the same core dual-driver, dual-receiver RS-232 function and 16-pin TSSOP footprint but does not provide the enhanced E-version protection specification. Select the newer E version for connector-exposed equipment unless cost, availability, or an approved component list makes the CPW part the better controlled alternative.
When should I choose MAX3232ECPWR over MAX3232IPW?
Choose MAX3232ECPWR when the design requires enhanced ±15 kV IEC ESD protection and operates within the commercial 0 °C to 70 °C range. Choose MAX3232IPW when the industrial temperature range is more important and enhanced ESD protection is not required. Both use the same 16-pin TSSOP interface arrangement, but their temperature grades and ESD capabilities should be compared against the enclosure, connector exposure, and system qualification requirements.
Where can I buy MAX3232ECPWR online?
Use the Request a Quote form on this page to request MAX3232ECPWR availability, commercial terms, and current lead time. The form allows engineers to identify the exact 16-pin TSSOP ordering code and request the quantity required for prototype or production builds. Stock status should be confirmed at the time of quotation because component inventory and lifecycle conditions can change.
What is the price of MAX3232ECPWR?
The current commercial price of MAX3232ECPWR is not fixed in a static product description because it can vary with order quantity, inventory, and supply conditions. Submit the Request a Quote form on this page with your required quantity, target date, and shipment location. The resulting quotation provides the exact price for MAX3232ECPWR rather than an unverified or outdated market figure.
What is the lead time and stock status of MAX3232ECPWR?
Current lead time and stock status should be confirmed through the Request a Quote form on this page. Provide the required quantity, production date, and any acceptable alternate sourcing conditions in the request. Texas Instruments lists the MAX3232E family as an active product, but short-term inventory, allocated production capacity, and package-specific availability can still vary.
What can replace MAX3232ECPWR?
A qualified replacement must match the 16-pin TSSOP footprint and preserve the 3 V to 5.5 V supply, 250 kbit/s data rate, dual-driver, and dual-receiver functions. Potential drop-in choices include MAX3232CPW, MAX3232IPW, MAX3232EWP, and ST3232CTR, subject to their individual temperature and ESD specifications. Review the manufacturer datasheet and qualification requirements rather than relying on package similarity alone.

Datos de referencia de ingeniería para MAX3232ECPWR — comparación, orientación de diseño e información de cumplimiento.

Guía de selección

Choose MAX3232ECPWR for a compact, commercial-temperature RS-232 interface that operates from 3 V or 5 V and benefits from ±15 kV IEC ESD protection. Its integrated dual charge pump eliminates a separate negative supply, and the 16-pin TSSOP package supports PCB reuse. Select MAX3232CPW only when the standard MAX3232 function is sufficient and component cost or approved sourcing is more important than enhanced E-version protection. Choose MAX3232IPW when the enclosure can fall below 0 °C or rise above 70 °C. MAX3232EWP is the closest enhanced-function ordering option when an alternate commercial TSSOP suffix is acceptable. ST3232CTR provides a cross-brand second source with matching core interface characteristics, but engineers should separately verify ESD, temperature, lifecycle, and qualification requirements before substitution.

Comparación con alternativas

Parámetro Este producto MAX3232CPW MAX3232IPW MAX3232EWP MAX3232EA ST3232CTR
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments STMicroelectronics
Package 16-TSSOP 16-TSSOP 16-TSSOP 16-TSSOP 16-TSSOP 16-TSSOP
Product Type Dual RS-232 transceiver Dual RS-232 transceiver Dual RS-232 transceiver Dual RS-232 transceiver Dual RS-232 transceiver Dual RS-232 transceiver
Supply Voltage Range 3 V to 5.5 V 3 V to 5.5 V 3 V to 5.5 V 3 V to 5.5 V 3 V to 5.5 V 3 V to 5.5 V
Maximum Data Rate 250 kbit/s 250 kbit/s 250 kbit/s 250 kbit/s 250 kbit/s 250 kbit/s
Line Drivers 2 channels 2 channels 2 channels 2 channels 2 channels 2 channels
Line Receivers 2 channels 2 channels 2 channels 2 channels 2 channels 2 channels
External Charge-Pump Capacitors 4 capacitors 4 capacitors 4 capacitors 4 capacitors 4 capacitors 4 capacitors

Diferenciadores clave

  • Enhanced connector-side ESD protection (frente a MAX3232CPW)
  • Commercial-temperature option supports cost-sensitive room-temperature equipment (frente a MAX3232IPW)
  • Single-supply operation simplifies embedded interfaces (frente a MC1488NE4)
  • Pin-compatible second-source option (frente a ST3232CTR)

Notas de diseño

Place the four charge-pump capacitors close to pins 7 through 10 using short traces and a compact ground connection. These nodes switch at high frequency, so excessive loop area can increase radiated emissions and coupling into nearby analog circuitry. Follow the capacitor values and topology shown in the Texas Instruments datasheet. Keep the RS-232-side routing away from clocks, ADC inputs, switching-regulator power nodes, and sensitive sensor signals.

Do not treat the MAX3232ECPWR as a 5 V-only RS-232 circuit. Its specified single-supply operating range is 3 V to 5.5 V, and the charge-pump capacitor requirements can vary with supply conditions. Use the manufacturer-recommended capacitor values and ensure that transmitter input levels remain compatible with the VCC rail. Also distinguish logic-side pins 12 and 13 from RS-232-side outputs 14 and 15 during schematic review.

The 30 V/µs maximum transmitter slew rate controls RS-232 edge speed, but cable and board radiation can still be significant. Route T1OUT and T2OUT as short, impedance-controlled paths to the connector, maintain a continuous ground reference beneath the pair, and avoid adding unnecessary stubs. For enclosure-mounted connectors, evaluate whether additional board-level TVS or surge protection is required rather than assuming the device's ±15 kV IEC ESD rating covers every external fault condition.

RS-232 is a single-ended, unbalanced interface, and ground potential differences can cause communication errors. Connect the transceiver ground to the connector ground with a low-impedance path and evaluate whether a chassis or signal-ground connection is required for long cable runs. Do not use the charge-pump V+ and V- pins as general supply rails; they are generated specifically for the line drivers and should not power external circuitry.

Información de cumplimiento

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Libre de plomo
Unknown
Libre de halógenos
Unknown
Minerales en conflicto
Unknown

The manufacturer product page confirms TIA/EIA-232-F compliance and ±15 kV IEC ESD protection, but it does not provide RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations.

Búsquedas relacionadas

MAX3232ECPWR datasheet MAX3232ECPWR pinout MAX3232ECPWR datasheet pdf MAX3232ECPWR schematic MAX3232ECPWR equivalent MAX3232ECPWR replacement MAX3232ECPWR cross reference MAX3232ECPWR vs ST3232CTR MAX3232ECPWR footprint MAX3232ECPWR price MAX3232ECPWR stock Texas Instruments MAX3232ECPWR MAX3232ECPWR RS-232 application circuit MAX3232 16-TSSOP pinout

Componentes & términos relacionados

Texas Instruments MAX3232ECPWR MAX3232E MAX3232CPW MAX3232IPW MAX3232EWP MAX3232EA STMicroelectronics ST3232CTR RS-232 RS-232 transceiver line driver line receiver interface IC serial transceiver TIA/EIA-232-F IEC ESD protection charge pump 16-TSSOP TSSOP family surface-mount package 3 V to 5.5 V supply 250 kbit/s industrial communication service console
RFQ de presupuesto rápido
Complete los detalles — nuestro equipo de ventas responderá en un plazo de 24 horas
Número de pieza Fabricante Encapsulado QTY Precio objetivo Total
✓
¡Presupuesto enviado!

Responderemos a su correo electrónico en un plazo de 24 horas

1
RFQ enviado
2
Presupuesto recibido
3
Pedido realizado
4
Pago
5
Enviado
6
Entregado
Ver detalles del RFQ