MAX323EUA+ - Dual SPST Analog Switch | Analog Devices
N.º de pieza: MAX323EUA+ ✓ ActivoMAX323EUA+ Descripción general
An analog switch is an integrated semiconductor device that connects or disconnects an electrical signal under logic control. The broader hierarchy is analog switch to analog switch and multiplexer or multiplexer IC to interface IC to semiconductor. Unlike a mechanical relay, an integrated analog switch can change signal state electronically without mechanical wear. The SPST designation describes one independently controlled switch per channel, while the normally open configuration leaves the switched path disconnected until its control input is asserted.
The MAX323EUA+ provides two precision SPST switches in one 8-uMAX/uSOP package. Its specified 60 ohm on-resistance supports controlled signal attenuation and loading analysis in precision analog-routing circuits. The 2.7 V to 16 V single-supply range allows operation from low-voltage battery systems through higher-voltage industrial control rails. The manufacturer also identifies 5 µW power consumption as a key benefit for battery-powered equipment.
The MAX323 family combines precision analog switching with low power consumption. Its two channels are configured as normally open switches, which simplifies designs that require a default disconnected state. The 8-uMAX/uSOP package reduces board area compared with larger leaded or SOIC implementations. Because an analog switch contributes finite on-resistance, charge injection, leakage, and control-interface behavior, the surrounding source impedance, signal amplitude, switching speed, and power rails determine the practical system performance.
Typical uses include battery-powered test equipment, precision measurement front ends, industrial control interfaces, and portable instrumentation. In each case, the two channels can route separate low-frequency control or analog signals while the 2.7 V minimum supply supports common single-supply systems. The 16 V maximum supply also permits operation from higher-voltage control systems without requiring a negative supply rail.
PCB design should keep the switched signal traces short and place control and bypass components close to the relevant pins. The analog input and output paths should avoid unnecessary switching regulators and high-current digital traces because the MAX323EUA+ is intended for signal routing rather than power switching. Confirm the complete pin description, control logic, and recommended operating conditions in the manufacturer datasheet before finalizing the schematic.
This page organizes the confirmed switch configuration, supply range, on-resistance, low-power characteristic, package information, engineering use cases, and verified sourcing records into one design-oriented reference. It also distinguishes documented MAX323EUA+ characteristics from package-only family options so engineers can assess PCB reuse and replacement decisions without confusing function with footprint compatibility.
Alternativas directas para MAX323EUA+ — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
No hay alternativas directas disponibles para este producto.
Solicitar alternativasMAX323EUA+ Valores máximos y características eléctricas
| Number of Switches | 2 |
| Switch Configuration | Dual SPST, normally open |
| On-Resistance | 60 ohm |
| Supply Voltage Range | +2.7 V to +16 V |
| Power Consumption | 5 µW |
| Encapsulado | 8-uMAX/uSOP |
| Tipo de montaje | Surface mount |
| Recuento de pines | 8 pins |
| Temperature Grade | Industrial |
Guía de configuración de pines de MAX323EUA+ 8-umax/usop
Configuración de pines para MAX323EUA+ (encapsulado 8-umax/usop). La numeración de pines, las funciones y los diagramas de conexión se definen en la hoja de datos del fabricante. Consúltela para conocer el footprint exacto y las directrices de soldadura.
No hay datos detallados de patillaje disponibles para MAX323EUA+.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
MAX323EUA+ es adecuado para 6 aplicacións: Battery-Powered Measurement Instruments, Industrial Control Signal Routing, Precision Analog Test Points, Portable Sensor Signal Switching, Programmable Signal-Path Selection, Low-Power Embedded Control Interfaces.
Battery-Powered Measurement Instruments
The MAX323EUA+ suits portable measurement equipment that must route two independent signals while drawing very little power. Its two normally open SPST channels provide a default disconnected condition, and the stated 5 µW power consumption supports battery-operated operation. The single-supply range begins at +2.7 V, allowing the switches to share a low-voltage rail when the control and measurement circuitry also uses that rail. With a specified 60 ohm on-resistance, the MAX323EUA+ should be used for signal paths whose source and receiver impedances tolerate the resulting loading. It is better suited to precision control and measurement lines than to power switching or high-current loads.
Recomendado
Industrial Control Signal Routing
The MAX323EUA+ can control two separate low-level signal paths in industrial equipment because each SPST channel operates independently. Its +2.7 V to +16 V supply range accommodates both compact embedded systems and higher-voltage control environments, while the industrial temperature grade supports equipment designed for demanding operating conditions. The normally open topology is useful when a powered-off or default control state must leave the routed path disconnected. Designers should evaluate the 60 ohm on-resistance against the driven input impedance and keep switched traces short to reduce pickup. The device is intended for analog or logic routing rather than driving motors, relays, or high-current loads.
Recomendado
Precision Analog Test Points
The MAX323EUA+ is appropriate for precision analog test-point routing where two channels must be connected under electronic control. The 60 ohm on-resistance is the primary design consideration because it interacts with the source impedance and the input resistance of the selected test path. Its compact 8-uMAX/uSOP package helps conserve board area in dense instrumentation, while the dual SPST organization simplifies two-point or source-selection arrangements. The single-supply operation from +2.7 V to +16 V avoids a negative supply in many systems. For high-accuracy measurements, verify leakage, charge injection, off-isolation, and switching-time limits in the manufacturer data sheet for the actual signal amplitude and impedance.
Recomendado
Portable Sensor Signal Switching
The MAX323EUA+ can switch sensor signals in a compact portable acquisition system where board area and standby consumption are important. Two normally open channels allow separate sensor or excitation paths to remain isolated until commanded, and the +2.7 V minimum supply supports integration with low-voltage mixed-signal systems. The specified 5 µW power characteristic is valuable when the instrument spends substantial time between measurements. The 60 ohm on-resistance must be included in the sensor-interface calculation, especially for high-impedance sources where leakage and loading can affect accuracy. Place the device close to the sensor connectors and keep sensitive routes away from switching power stages to preserve measurement integrity.
Recomendado
Programmable Signal-Path Selection
The MAX323EUA+ fits compact programmable signal-path selection because it provides two independently controlled, normally open SPST switches in one 8-uMAX/uSOP package. Control logic can determine whether each analog or low-frequency digital path is connected, while the default open state helps prevent unintended coupling between circuits. Single-supply operation from +2.7 V to +16 V allows common integration with modern control systems, and the 60 ohm on-resistance defines the insertion loss imposed on the selected path. The package should be placed near the routed nodes to minimize trace susceptibility. Confirm control levels, switching time, leakage, and charge injection against the system requirements before using the switch for precision multiplexing functions.
Recomendado
Low-Power Embedded Control Interfaces
The MAX323EUA+ is useful in embedded controllers that need to route two low-current signals without adding another relay or mechanical selector. Its 5 µW power consumption and single +2.7 V to +16 V operating range support low-power architecture, while the normally open channels allow reset, test, or enable lines to remain disconnected during default operation. The small 8-uMAX/uSOP package reduces routing congestion around the controller. Designers must include the 60 ohm on-resistance when calculating voltage division with downstream input impedance and should observe the control-input thresholds from the data sheet. This application concerns low-level signal routing; the switch should not be used to control power rails or devices whose load current exceeds the device's intended function.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para MAX323EUA+ — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto |
|---|---|
| Switch Count | 2 |
| Switch Configuration | Dual SPST, normally open |
| On-Resistance | 60 ohm |
| Supply Voltage Range | +2.7 V to +16 V |
| Power Consumption | 5 µW |
| Package | 8-uMAX/uSOP |
| Brand | Analog Devices |
| Mounting Type | Surface mount |
Diferenciadores clave
- Compact package for dual-channel routing (frente a MAX323ESA)
- Defined normally open dual-channel behavior (frente a MAX323CSA)
- Single-supply operation across portable and industrial rails (frente a MAX323ESA)
Notas de diseño
Include the specified 60 ohm on-resistance when calculating attenuation with the source impedance and receiving input impedance. For a high-impedance source, the switch resistance may be minor; for a low-impedance source, it can create a meaningful divider. Also verify off-isolation, leakage, and charge-injection limits in the manufacturer data sheet before using the channel for precision low-level signals.
Place the MAX323EUA+ close to the switched nodes and control logic to minimize sensitive trace length. Keep the two switched paths physically separated where crosstalk or capacitive coupling could affect a measurement, and route them away from high-current switching nodes. Provide local supply bypassing according to the family data sheet, and observe the package pin assignments and exposed-contact requirements exactly as drawn in the manufacturer documentation.
Design the control and supply rails for the stated +2.7 V to +16 V operating interval and account for the family's 5 µW power-consumption characteristic when estimating portable-system consumption. The device is a low-level analog switch, not a power switch. Do not use it for motors, solenoids, high-current loads, or direct relay-coil drive; use an appropriate driver stage for those loads.
Do not treat another MAX323 suffix as a footprint substitute without checking the package drawing. The MAX323EUA+ uses the 8-uMAX/uSOP package, whereas MAX323ESA-family listings identify an 8-pin SOIC package. Verify pin numbering, body dimensions, lead geometry, and land pattern before redesigning a PCB. A shared family name and function do not guarantee that a different package can be soldered onto the same footprint.
Información de cumplimiento
The manufacturer page identifies MAX323 as a production family, but no explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status was captured for the exact MAX323EUA+ ordering code.