MAX337CPI+ - Dual 8-Channel CMOS Multiplexer | Analog Devices
N.º de pieza: MAX337CPI+ ✓ ActivoMAX337CPI+ Descripción general
An analog multiplexer is an interface IC that connects one selected input to a shared output. In the multiplexer's functional hierarchy, the MAX337CPI+ belongs to the analog switch and multiplexer class, then to interface ICs, and finally to the broader semiconductor category. This architecture reduces the number of signal paths required by test equipment, data-acquisition systems, industrial controllers, and measurement instruments while preserving controlled access to multiple analog inputs.
Key characteristics include a dual 8-channel configuration, low leakage, 400 ohm maximum on resistance, and operation across a 4.5 V to 30 V supply range. The device supports a maximum dual supply of ±20 V, enabling signal paths near the limits of its supply architecture when suitable protections are applied. Its commercial operating-temperature range is 0°C to 70°C, while maximum power dissipation is 1.14 W.
The MAX337CPI+ uses CMOS multiplexing to route analog signals with digital address control. Its two 8:1 sections are controlled by address inputs and separate enable logic, allowing a system to select channels independently or apply coordinated selection across both banks. The 28-pin PDIP package provides through-hole accessibility and is suitable for prototypes, legacy industrial equipment, and instruments assembled with manual insertion.
Typical uses include automated test systems, data-acquisition units, process-control panels, instrumentation, and analog signal-routing boards. In each system, the multiplexer reduces wiring complexity by sharing output circuitry among multiple sensed or measured channels. Designers should account for source impedance, settling time, injected switching noise, and the voltage limits of the connected signals.
For layout, keep analog input and output traces away from fast digital control lines, use a quiet ground reference, and terminate unused channels according to the application architecture. Confirm signal amplitude, common-mode range, supply polarity, address timing, and power dissipation before committing the 28-pin footprint to a new PCB.
This product page consolidates the device function, electrical limits, package details, purchasing guidance, and design considerations into one engineering reference. It also distinguishes verified functional characteristics from the parameters engineers should confirm in the manufacturer datasheet before layout or production release.
Alternativas directas para MAX337CPI+ — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
MAX337EPI+
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
MAX337EPE+
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
MAX337CPE+
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
MAX337CPI+ Especificaciones
| Multiplexer Configuration | Dual 8:1 |
| Total Channel Count | 16 channels |
| Number of Circuits | 2 circuits |
| Technology | CMOS |
| Maximum On-State Resistance | 400 ohm |
| Minimum Supply Voltage | 4.5 V |
| Maximum Supply Voltage | 30 V |
| Maximum Dual Supply Voltage | ±20 V |
| Rango de temperatura de funcionamiento | 0°C to 70°C |
| Maximum Power Dissipation | 1.14 W |
| Off-State Isolation | 82 dB nominal |
| Package Type | 28-pin PDIP |
| Package Code | PDIP |
| Number of Terminals | 28 terminals |
| Tipo de montaje | Through-hole insertion |
| Leakage Characteristic | Low leakage |
| Temperature Grade | Commercial |
| Production Status | PRODUCTION |
Guía de configuración de pines de MAX337CPI+ pdip
Configuración de pines para MAX337CPI+ (encapsulado pdip). La numeración de pines, las funciones y los diagramas de conexión se definen en la hoja de datos del fabricante. Consúltela para conocer el footprint exacto y las directrices de soldadura.
No hay datos detallados de patillaje disponibles para MAX337CPI+.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
MAX337CPI+ es adecuado para 6 aplicacións: Automated Test Equipment, Data Acquisition Systems, Process Control Instrumentation, Laboratory Signal Routing, Industrial Control Panels, Legacy Instrumentation Retrofit.
Automated Test Equipment
The MAX337CPI+ is suitable for automated test equipment that must connect several analog measurement points to a shared instrument channel. Its dual 8:1 organization provides 16 switched inputs in a single 28-pin PDIP package, reducing the number of separate front-panel connections and simplifying the address-control logic. The 400 ohm maximum on-state resistance can be suitable for medium-impedance sensing paths when the required settling accuracy is evaluated. Because the device operates from 4.5 V to 30 V, it accommodates low-voltage and higher-voltage analog test interfaces. Designers should verify input and output voltage limits, leakage behavior, switch timing, and source impedance in the manufacturer data sheet before assigning the multiplexer to precision measurements.
Recomendado
Data Acquisition Systems
The MAX337CPI+ can route grouped analog inputs in data-acquisition systems where multiple sensors or conditioned measurement channels must be selected sequentially. Each 8-channel bank connects one input to a common output, allowing a system to use shared amplification and conversion circuitry rather than duplicating those stages for every channel. Its low-leakage CMOS construction is useful when the acquired signal must not be significantly disturbed by the switch. The 400 ohm maximum on resistance and up to 30 V supply capability provide useful design boundaries, but the application must still account for source impedance, settling time, injected noise, and protection requirements. The commercial 0°C to 70°C range suits temperature-controlled laboratory or industrial electronics.
Recomendado
Process Control Instrumentation
The MAX337CPI+ is appropriate for process-control instrumentation that scans several analog inputs for supervisory measurement, alarm evaluation, or diagnostic checks. Two independent 8-channel sections can organize signals by subsystem, allowing address-controlled access to pressure, temperature, or position feedback without connecting every field signal to a separate processing channel. Its 4.5 V minimum supply supports lower-voltage control electronics, while its maximum dual supply of ±20 V can serve bipolar signal interfaces when correctly biased. The 28-pin PDIP package supports instrument prototypes and through-hole maintenance assemblies. Engineers should confirm the analog input common-mode range, leakage, switching transients, and 1.14 W maximum power dissipation against the enclosure temperature and grounding strategy.
Recomendado
Laboratory Signal Routing
The MAX337CPI+ can serve as a laboratory signal router for connecting multiple external or internally generated analog signals to a shared oscilloscope, meter, or amplifier input. The dual 8:1 structure provides two independent routing groups, which helps organize a bench instrument around two measurement banks. Its low-leakage behavior limits unwanted signal disturbance, and the stated 400 ohm maximum on resistance is an important consideration for high-impedance sources. The commercial temperature range of 0°C to 70°C is appropriate for controlled indoor instruments. For precision measurements, verify the selected channel’s settling behavior, off-state isolation, bandwidth, and allowable input voltage, and place the device away from high-energy switching nodes and noisy digital clock lines.
Recomendado
Industrial Control Panels
The MAX337CPI+ fits industrial control panels that monitor multiple analog feedback points but have limited connector and front-end space. Its two 8-channel banks allow a controller to select among grouped sensor outputs through digital addressing, while the shared outputs feed common signal-conditioning stages. The 28-pin PDIP format is particularly practical for legacy or manually assembled control equipment, and the 4.5 V to 30 V operating range accommodates several industrial supply architectures. Designers should ensure that selected signals remain within the device's analog limits and use appropriate protection for long wiring or exposed sensor inputs. Grounding, channel settling, power bypass, and thermal dissipation should be reviewed in the final enclosure because long signal cables can introduce noise and surge transients.
Recomendado
Legacy Instrumentation Retrofit
The MAX337CPI+ is a practical choice for retrofitting legacy instrumentation that uses a 28-pin PDIP multiplexer footprint and requires a dual 8-channel routing function. The through-hole package can support board-level repair without changing the mechanical design of an established instrument. Its PRODUCTION family status and 0°C to 70°C commercial range support controlled indoor environments, while the 4.5 V to 30 V supply range offers flexibility in mixed legacy power systems. A retrofit should not assume that every MAX337 ordering code is interchangeable: compare the complete pinout, supply configuration, logic thresholds, leakage, on resistance, and timing in the manufacturer documentation. The observed 400 ohm on resistance must also be checked against the accuracy and input impedance of the original measurement circuit.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para MAX337CPI+ — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | MAX337EPI+ | MAX337EPE+ | MAX337CPE+ |
|---|---|---|---|---|
| Package | 28-pin PDIP | 28-pin PDIP | 28-pin PDIP | 28-pin PDIP |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Multiplexer Configuration | Dual 8:1 | Dual 8:1 | Dual 8:1 | Dual 8:1 |
| Total Channels | 16 channels | 16 channels | 16 channels | 16 channels |
| Technology | CMOS | CMOS | CMOS | CMOS |
Diferenciadores clave
- Dual 8:1 routing in one package (frente a MAX336)
- Through-hole 28-pin PDIP package (frente a MAX337EWI+T)
- 400 ohm maximum on-state resistance for the exact device (frente a MAX337EWI+T)
- Production dual 8-channel CMOS multiplexer option (frente a MAX337EWI+T)
Notas de diseño
Treat the multiplexed output as a switched analog node rather than an ideal wire. The stated maximum on-state resistance is 400 ohm, so source impedance, load impedance, and the required settling accuracy determine whether the selected channel introduces acceptable attenuation. Use the manufacturer switching-time and capacitance tables to calculate an acquisition settling interval before sampling immediately after an address change. For high-impedance sources, guard routing, leakage, and PCB contamination can matter as much as the nominal on resistance.
Place the MAX337CPI+ close to the shared analog output and associated input-conditioning circuitry so switched-channel traces remain short. Route address and enable signals away from sensitive analog inputs, and provide a continuous ground reference beneath the signal path. Because this is a 28-pin PDIP device intended for through-hole assembly, provide adequate spacing around the package for probe access and check the board for copper keepouts that might interfere with a socket or heat-shrink insulation.
Use the 4.5 V to 30 V supply range as a hard selection boundary and confirm the actual analog signal levels against the device's absolute maximum ratings. Bypass each supply rail close to the package and keep the return-current path short to reduce supply noise at the multiplexer. The listed maximum power dissipation is 1.14 W; use that limit together with the actual supply voltage, selected-channel loading, and enclosure temperature to establish thermal headroom rather than treating the maximum as a continuous operating target.
Do not confuse the MAX337 dual 8:1 configuration with the single 16-channel MAX336 architecture. Address decoding, enable polarity, and channel numbering must match the PCB schematic and firmware. Also do not treat the MAX337EWI+T as a direct replacement: it uses a surface-mount SOIC package even though its functional specifications are similar. For any retrofit, verify all 28 pin assignments and control thresholds against the manufacturer pin-description and electrical-characteristics tables.
Información de cumplimiento
The MAX337 family is listed as production, but no explicit RoHS, REACH, lead-free, halogen-free, conflict-minerals, or AEC-Q100 statement was available for the exact ordering code. AEC-Q100 is not applicable because this is a commercial interface multiplexer rather than an automotive-qualified device.