Analog Devices

MAX337CPI+ - Dual 8-Channel CMOS Multiplexer | Analog Devices

料号: MAX337CPI+ ✓ 量产中
4.5 V Vdss 400 ohm Rds(on) 28-pin PDIP Package
最小起订量: 1 |

MAX337CPI+ 概述

Analog Devices MAX337CPI+ is a dual, 8-channel, low-leakage CMOS analog multiplexer with a 400 ohm maximum on-state resistance, operating from 4.5 V to 30 V in a 28-pin PDIP package. The device routes two independent groups of eight analog inputs to their respective outputs using digital address and enable control signals.

An analog multiplexer is an interface IC that connects one selected input to a shared output. In the multiplexer's functional hierarchy, the MAX337CPI+ belongs to the analog switch and multiplexer class, then to interface ICs, and finally to the broader semiconductor category. This architecture reduces the number of signal paths required by test equipment, data-acquisition systems, industrial controllers, and measurement instruments while preserving controlled access to multiple analog inputs.

Key characteristics include a dual 8-channel configuration, low leakage, 400 ohm maximum on resistance, and operation across a 4.5 V to 30 V supply range. The device supports a maximum dual supply of ±20 V, enabling signal paths near the limits of its supply architecture when suitable protections are applied. Its commercial operating-temperature range is 0°C to 70°C, while maximum power dissipation is 1.14 W.

The MAX337CPI+ uses CMOS multiplexing to route analog signals with digital address control. Its two 8:1 sections are controlled by address inputs and separate enable logic, allowing a system to select channels independently or apply coordinated selection across both banks. The 28-pin PDIP package provides through-hole accessibility and is suitable for prototypes, legacy industrial equipment, and instruments assembled with manual insertion.

Typical uses include automated test systems, data-acquisition units, process-control panels, instrumentation, and analog signal-routing boards. In each system, the multiplexer reduces wiring complexity by sharing output circuitry among multiple sensed or measured channels. Designers should account for source impedance, settling time, injected switching noise, and the voltage limits of the connected signals.

For layout, keep analog input and output traces away from fast digital control lines, use a quiet ground reference, and terminate unused channels according to the application architecture. Confirm signal amplitude, common-mode range, supply polarity, address timing, and power dissipation before committing the 28-pin footprint to a new PCB.

This product page consolidates the device function, electrical limits, package details, purchasing guidance, and design considerations into one engineering reference. It also distinguishes verified functional characteristics from the parameters engineers should confirm in the manufacturer datasheet before layout or production release.

直接替换替代料: MAX337CPI+ ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。

MAX337EPI+

✅ 直接替换 ⚠️ 规格未核验
📦 28-pin PDIP
Wider industrial temperature coverage than the 0°C to 70°C MAX337CPI+ while retaining the same 28-pin PDIP footprint and dual 8:1 multiplexer architecture.

📋 参考替代料(不在目录中)

MAX337EPE+

✅ 直接替换 ⚠️ 规格未核验
📦 28-pin PDIP
Uses the wider industrial-temperature MAX337 family configuration in the same 28-pin PDIP package; the key difference from MAX337CPI+ is temperature grade rather than multiplexer topology.

📋 参考替代料(不在目录中)

MAX337CPE+

✅ 直接替换 ⚠️ 规格未核验
📦 28-pin PDIP
Retains the 28-pin PDIP package and dual 8-channel CMOS multiplexer function; ordering and temperature characteristics should be checked against the manufacturer ordering table.

📋 参考替代料(不在目录中)

MAX337CPI+ 规格参数

Multiplexer Configuration Dual 8:1
Total Channel Count 16 channels
Number of Circuits 2 circuits
Technology CMOS
Maximum On-State Resistance 400 ohm
Minimum Supply Voltage 4.5 V
Maximum Supply Voltage 30 V
Maximum Dual Supply Voltage ±20 V
工作温度范围 0°C to 70°C
Maximum Power Dissipation 1.14 W
Off-State Isolation 82 dB nominal
Package Type 28-pin PDIP
Package Code PDIP
Number of Terminals 28 terminals
安装类型 Through-hole insertion
Leakage Characteristic Low leakage
Temperature Grade Commercial
Production Status PRODUCTION

MAX337CPI+ pdip 引脚配置指南

MAX337CPI+(pdip 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。

MAX337CPI+ 的 pdip 封装引脚图

暂无详细引脚数据: MAX337CPI+.

请参阅 数据手册 以查看完整引脚配置。

典型应用

MAX337CPI+ 适用于 6 应用s: Automated Test Equipment, Data Acquisition Systems, Process Control Instrumentation, Laboratory Signal Routing, Industrial Control Panels, Legacy Instrumentation Retrofit.

🖥️

Automated Test Equipment

The MAX337CPI+ is suitable for automated test equipment that must connect several analog measurement points to a shared instrument channel. Its dual 8:1 organization provides 16 switched inputs in a single 28-pin PDIP package, reducing the number of separate front-panel connections and simplifying the address-control logic. The 400 ohm maximum on-state resistance can be suitable for medium-impedance sensing paths when the required settling accuracy is evaluated. Because the device operates from 4.5 V to 30 V, it accommodates low-voltage and higher-voltage analog test interfaces. Designers should verify input and output voltage limits, leakage behavior, switch timing, and source impedance in the manufacturer data sheet before assigning the multiplexer to precision measurements.

📡

Data Acquisition Systems

The MAX337CPI+ can route grouped analog inputs in data-acquisition systems where multiple sensors or conditioned measurement channels must be selected sequentially. Each 8-channel bank connects one input to a common output, allowing a system to use shared amplification and conversion circuitry rather than duplicating those stages for every channel. Its low-leakage CMOS construction is useful when the acquired signal must not be significantly disturbed by the switch. The 400 ohm maximum on resistance and up to 30 V supply capability provide useful design boundaries, but the application must still account for source impedance, settling time, injected noise, and protection requirements. The commercial 0°C to 70°C range suits temperature-controlled laboratory or industrial electronics.

🏭

Process Control Instrumentation

The MAX337CPI+ is appropriate for process-control instrumentation that scans several analog inputs for supervisory measurement, alarm evaluation, or diagnostic checks. Two independent 8-channel sections can organize signals by subsystem, allowing address-controlled access to pressure, temperature, or position feedback without connecting every field signal to a separate processing channel. Its 4.5 V minimum supply supports lower-voltage control electronics, while its maximum dual supply of ±20 V can serve bipolar signal interfaces when correctly biased. The 28-pin PDIP package supports instrument prototypes and through-hole maintenance assemblies. Engineers should confirm the analog input common-mode range, leakage, switching transients, and 1.14 W maximum power dissipation against the enclosure temperature and grounding strategy.

🔧

Laboratory Signal Routing

The MAX337CPI+ can serve as a laboratory signal router for connecting multiple external or internally generated analog signals to a shared oscilloscope, meter, or amplifier input. The dual 8:1 structure provides two independent routing groups, which helps organize a bench instrument around two measurement banks. Its low-leakage behavior limits unwanted signal disturbance, and the stated 400 ohm maximum on resistance is an important consideration for high-impedance sources. The commercial temperature range of 0°C to 70°C is appropriate for controlled indoor instruments. For precision measurements, verify the selected channel’s settling behavior, off-state isolation, bandwidth, and allowable input voltage, and place the device away from high-energy switching nodes and noisy digital clock lines.

⚡

Industrial Control Panels

The MAX337CPI+ fits industrial control panels that monitor multiple analog feedback points but have limited connector and front-end space. Its two 8-channel banks allow a controller to select among grouped sensor outputs through digital addressing, while the shared outputs feed common signal-conditioning stages. The 28-pin PDIP format is particularly practical for legacy or manually assembled control equipment, and the 4.5 V to 30 V operating range accommodates several industrial supply architectures. Designers should ensure that selected signals remain within the device's analog limits and use appropriate protection for long wiring or exposed sensor inputs. Grounding, channel settling, power bypass, and thermal dissipation should be reviewed in the final enclosure because long signal cables can introduce noise and surge transients.

🔧

Legacy Instrumentation Retrofit

The MAX337CPI+ is a practical choice for retrofitting legacy instrumentation that uses a 28-pin PDIP multiplexer footprint and requires a dual 8-channel routing function. The through-hole package can support board-level repair without changing the mechanical design of an established instrument. Its PRODUCTION family status and 0°C to 70°C commercial range support controlled indoor environments, while the 4.5 V to 30 V supply range offers flexibility in mixed legacy power systems. A retrofit should not assume that every MAX337 ordering code is interchangeable: compare the complete pinout, supply configuration, logic thresholds, leakage, on resistance, and timing in the manufacturer documentation. The observed 400 ohm on resistance must also be checked against the accuracy and input impedance of the original measurement circuit.

推荐产品汇总

MAX337CPI+ Analog Devices 用于: Automated Test Equipment, Data Acquisition Systems, Process Control Instrumentation, Laboratory Signal Routing, Industrial Control Panels, Legacy Instrumentation Retrofit MAX337EWI+T Surface-mount family alternative for new layouts 用于: Automated Test Equipment, Process Control Instrumentation, Industrial Control Panels MAX336 Related single 16-channel MAX multiplexer family 用于: Data Acquisition Systems, Laboratory Signal Routing, Legacy Instrumentation Retrofit
What is the MAX337CPI+ used for?
The MAX337CPI+ is a dual 8-channel CMOS analog multiplexer used to route two independent banks of analog signals to shared outputs. According to the Analog Devices MAX337 product page, each half of the device selects one of eight inputs through digital address control. This reduces wiring and input-stage complexity in test systems, data-acquisition equipment, industrial controllers, and instrumentation while preserving low-leakage analog switching.
How many channels does the MAX337CPI+ have?
The MAX337CPI+ provides 16 analog channels arranged as two independent 8-channel sections. Each section has an 8:1 configuration, allowing one input from that bank to connect to its common output at a time. The Analog Devices MAX337 product page identifies the MAX337 family as a dual 8-channel, low-leakage CMOS multiplexer, while distributor product information identifies MAX337CPI+ specifically as a two-circuit 8:1 switch IC.
What is the maximum on-resistance of MAX337CPI+?
The MAX337CPI+ has a maximum on-state resistance of 400 ohm, according to the product listing for this exact device. This value determines the series loss introduced when a selected analog signal passes through the switch. Designers should include the source impedance, load impedance, and signal-settling requirements when determining whether 400 ohm is acceptable for the measurement accuracy and bandwidth of the application.
What supply voltage does MAX337CPI+ require?
The MAX337CPI+ operates from 4.5 V to 30 V, with a maximum dual-supply capability of ±20 V. The Analog Devices MAX337 family is designed for dual-supply analog multiplexing, while the device also provides a stated maximum on resistance of 400 ohm. Confirm whether the target circuit uses positive-only or dual-rail power before selecting bypass capacitors and protection components.
What package and temperature range does MAX337CPI+ use?
The MAX337CPI+ is packaged in a 28-pin PDIP and is specified for a commercial temperature range of 0°C to 70°C. Product information also lists maximum power dissipation as 1.14 W. The through-hole package is useful for manually assembled prototypes and legacy industrial equipment, but a surface-mount counterpart should be selected when board area or automated assembly is the controlling requirement.
Is MAX337CPI+ still in production?
The Analog Devices product page lists MAX337 as PRODUCTION, so the MAX337 family is presented as a current product rather than an obsolete device. The exact commercial ordering code MAX337CPI+ also appears in current distributor product records. Use the Request a Quote form on this page to confirm current availability, minimum order quantity, and delivery timing for the specific 28-pin PDIP ordering code.
Where can I download the MAX337CPI+ datasheet PDF?
The official MAX337 documentation and data sheet are available from the Analog Devices product page linked on this page. The manufacturer product page is the preferred source for the electrical characteristics, pin configuration, package information, and ordering table. Use the manufacturer datasheet to verify address and enable logic, absolute maximum ratings, switching timing, leakage currents, and the complete 28-pin assignment before releasing a PCB design.
Where can I find the MAX337CPI+ pinout?
The MAX337CPI+ pin configuration is documented in the pin-description section of the Analog Devices MAX337 data sheet. The device uses a 28-pin PDIP package, so each external connection and supply pin must be assigned according to that table. Use the pin-description table for PCB routing rather than inferring pin functions from channel order, because address, enable, and power pins are distributed across the package.
What can replace the MAX337CPI+?
The closest same-family drop-in choices are the MAX337EPI+ and MAX337EPE+ 28-pin PDIP versions, with MAX337CPE+ offering another same-package ordering option. Their key tradeoff is temperature coverage rather than multiplexer architecture. No cross-brand 28-pin PDIP equivalent was established, and a device in a different package is not a true drop-in replacement because PCB and assembly changes would be required.
Is the MAX337CPI+ the same as MAX337EWI+T?
No, the MAX337CPI+ and MAX337EWI+T are not direct drop-in equivalents because their packages differ. The MAX337CPI+ uses a 28-pin PDIP package, while the MAX337EWI+T uses a 28-lead SOIC package. Their channel configuration, supply limits, and resistance are similar, but changing between them requires a new footprint and different lead geometry, so the MAX337EWI+T is not a board-level replacement.
When should I choose MAX337CPI+ over MAX337EPI+?
Choose the MAX337CPI+ when the equipment operates within a commercial 0°C to 70°C enclosure and the 28-pin PDIP package is compatible with the assembly process. Choose MAX337EPI+ when the same MAX337 architecture is needed over a wider industrial temperature range while retaining the PDIP package. Confirm the complete pin, supply, timing, and logic compatibility in the manufacturer documentation before substitution.
Where can I buy MAX337CPI+ online?
Use the Request a Quote form on this page to request MAX337CPI+ availability, current commercial terms, and lead time. The exact device is listed as a 28-pin PDIP dual 8-channel CMOS multiplexer and is associated with current manufacturer production. Quote requests preserve the exact MAX337CPI+ ordering code and help confirm the quantity, packaging, and delivery requirements for your production build.
What is the price of MAX337CPI+?
The current commercial price for MAX337CPI+ should be obtained through the Request a Quote form on this page. The form is the appropriate channel for unit pricing, quantity discounts, and lead-time confirmation because market pricing can change with quantity, availability, and sourcing conditions. Provide the required quantity and intended package configuration when submitting the request.
What is the lead time for MAX337CPI+?
The current lead time for MAX337CPI+ should be requested through the Request a Quote form on this page. Lead time depends on order quantity, production scheduling, and the requested 28-pin PDIP configuration, so it should not be inferred from generic distributor inventory. State the required quantity and target delivery date when requesting a quotation.
What are the key specifications engineers should know about MAX337CPI+?
The key MAX337CPI+ specifications are a dual 8:1 configuration, 16 total channels, 400 ohm maximum on-state resistance, a 4.5 V to 30 V supply range, and a 28-pin PDIP package. The device is a production, commercial-temperature part rated for 0°C to 70°C with 1.14 W maximum power dissipation. These figures define its basic electrical, environmental, and mechanical boundaries for system design.
MAX337CPI+ vs MAX337EWI+T: which package should I choose?
Choose the MAX337CPI+ when through-hole assembly and an existing 28-pin PDIP footprint are required; choose MAX337EWI+T when surface-mount assembly and the 28-lead SOIC footprint are preferred. The comparison information identifies the same 8-channel configuration, 4.5 V to 30 V supply range, and 700 ohm maximum resistance, while the exact MAX337CPI+ listing identifies 400 ohm. The package difference prevents direct interchangeability.

工程参考数据: MAX337CPI+ ——对比、设计指导和合规信息。

选型指南

Choose MAX337CPI+ for a through-hole 28-pin PDIP design requiring a production, dual 8-channel low-leakage CMOS multiplexer with a 4.5 V to 30 V supply range and a commercial 0°C to 70°C operating range. Its 400 ohm maximum on-state resistance should be checked against source impedance, measurement accuracy, and settling requirements. Select MAX337EPI+ or MAX337EPE+ when the same PDIP footprint is needed but wider industrial temperature coverage is required. MAX337CPE+ is another same-package family option whose ordering and temperature details should be checked against the manufacturer table. MAX337EWI+T is functionally similar but uses a 28-lead SOIC package, so it is appropriate for a new surface-mount PCB rather than a direct retrofit. Use the single 16-channel MAX336 architecture when one common output and one select-enable structure are preferred instead of two independent 8-channel banks.

与替代料对比

参数 本产品 MAX337EPI+ MAX337EPE+ MAX337CPE+
Package 28-pin PDIP 28-pin PDIP 28-pin PDIP 28-pin PDIP
Brand Analog Devices Analog Devices Analog Devices Analog Devices
Multiplexer Configuration Dual 8:1 Dual 8:1 Dual 8:1 Dual 8:1
Total Channels 16 channels 16 channels 16 channels 16 channels
Technology CMOS CMOS CMOS CMOS

关键差异点

  • Dual 8:1 routing in one package (对比 MAX336)
  • Through-hole 28-pin PDIP package (对比 MAX337EWI+T)
  • 400 ohm maximum on-state resistance for the exact device (对比 MAX337EWI+T)
  • Production dual 8-channel CMOS multiplexer option (对比 MAX337EWI+T)

设计说明

Treat the multiplexed output as a switched analog node rather than an ideal wire. The stated maximum on-state resistance is 400 ohm, so source impedance, load impedance, and the required settling accuracy determine whether the selected channel introduces acceptable attenuation. Use the manufacturer switching-time and capacitance tables to calculate an acquisition settling interval before sampling immediately after an address change. For high-impedance sources, guard routing, leakage, and PCB contamination can matter as much as the nominal on resistance.

Place the MAX337CPI+ close to the shared analog output and associated input-conditioning circuitry so switched-channel traces remain short. Route address and enable signals away from sensitive analog inputs, and provide a continuous ground reference beneath the signal path. Because this is a 28-pin PDIP device intended for through-hole assembly, provide adequate spacing around the package for probe access and check the board for copper keepouts that might interfere with a socket or heat-shrink insulation.

Use the 4.5 V to 30 V supply range as a hard selection boundary and confirm the actual analog signal levels against the device's absolute maximum ratings. Bypass each supply rail close to the package and keep the return-current path short to reduce supply noise at the multiplexer. The listed maximum power dissipation is 1.14 W; use that limit together with the actual supply voltage, selected-channel loading, and enclosure temperature to establish thermal headroom rather than treating the maximum as a continuous operating target.

Do not confuse the MAX337 dual 8:1 configuration with the single 16-channel MAX336 architecture. Address decoding, enable polarity, and channel numbering must match the PCB schematic and firmware. Also do not treat the MAX337EWI+T as a direct replacement: it uses a surface-mount SOIC package even though its functional specifications are similar. For any retrofit, verify all 28 pin assignments and control thresholds against the manufacturer pin-description and electrical-characteristics tables.

合规信息

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
无铅
Unknown
无卤
Unknown
冲突矿物
Unknown

The MAX337 family is listed as production, but no explicit RoHS, REACH, lead-free, halogen-free, conflict-minerals, or AEC-Q100 statement was available for the exact ordering code. AEC-Q100 is not applicable because this is a commercial interface multiplexer rather than an automotive-qualified device.

相关搜索

MAX337CPI+ MAX337CPI+ datasheet MAX337CPI+ datasheet pdf MAX337CPI+ pinout MAX337CPI+ equivalent MAX337CPI+ replacement MAX337CPI+ cross reference MAX337CPI+ vs MAX337EWI+T Analog Devices MAX337CPI+ MAX337CPI+ 28 pin PDIP MAX337CPI+ dual 8 channel multiplexer MAX337CPI+ price MAX337CPI+ stock MAX337CPI+ lead time MAX337CPI+ instrumentation application

相关元器件 & 术语

Analog Devices MAX337CPI+ MAX337EPI+ MAX337EPE+ MAX337CPE+ MAX337EWI+T MAX336 analog multiplexer analog switch interface IC CMOS dual 8:1 multiplexer 16-channel multiplexing on-state resistance low leakage 28-pin PDIP PDIP through-hole package supply voltage dual supply off-state isolation data acquisition automated test equipment process control instrumentation commercial temperature grade
快速报价
填写完整信息——我们的销售团队将在 24 小时内回复
料号 制造商 封装 QTY 目标价 小计
✓
报价已提交!

我们将在 24 小时内回复您的邮件

1
询价已提交
2
已收到报价
3
已下单
4
支付
5
已发货
6
已送达
查看询价详情