Analog Devices

MAX3384EEAP - 3V RS-232 Transceiver, 250kbps | Analog Devices

N.º de pieza: MAX3384EEAP ✓ Activo
3 V to 5.5 V Vdss 1 µA Id SSOP-20, 5.30 mm, 0.65 mm pitch Package
MOQ: 1 |

MAX3384EEAP Descripción general

The Analog Devices MAX3384EEAP is a 3V-powered EIA/TIA-232 and V.28/V.24 communications transceiver with two drivers and two receivers in a 20-pin SSOP package. It supports operation from 3V to 5.5V, delivers data rates up to 250kbps, and provides enhanced electrostatic discharge protection on the transmitter outputs and receiver inputs. The device is designed for low-power RS-232 links where supply voltage, communication speed, and transient protection are the primary design requirements.

An RS-232 transceiver is an interface IC that converts logic-level UART signals into RS-232 bipolar levels and converts received RS-232 levels back into CMOS-compatible logic. The MAX3384EEAP belongs to the interface IC hierarchy alongside serial transceivers, line drivers, and level-shifting ICs. Its two-driver, two-receiver arrangement supports full-duplex point-to-point communication, including flow-control lines between two data-terminal systems.

Key features include a 3V to 5.5V supply range, operation up to 250kbps, low-power operation with shutdown and receiver active-low features, and ±15kV air-gap ESD protection on all transmitter outputs and receiver inputs. Contact discharge protection is rated at ±8kV using the IEC 1000-4-2 test method. These protection levels are important when the connector is exposed to cable discharge events or an industrial noise environment.

The MAX3384E uses charge-pump circuitry to generate the bipolar voltage required by the RS-232 drivers, allowing operation from a single low-voltage supply. This architecture eliminates the need for a separate negative supply rail. The resulting single-supply implementation reduces board complexity in systems that already operate from 3.3V or 5V, while the driver stage provides the voltage swing expected by RS-232 receivers.

Typical applications include industrial serial consoles, point-of-sale terminals, data-acquisition equipment, instrument control links, and embedded systems that communicate with legacy RS-232 peripherals. The 250kbps maximum data rate supports modern UART traffic while remaining compatible with the slower signaling commonly used by V.28 and V.24 equipment. The package is also suitable for compact control boards where connector access is limited.

When laying out the circuit, place the device close to the RS-232 connector to minimize the length of unprotected traces between the IC and connector. Follow the pin-description and decoupling guidance in the manufacturer datasheet, and maintain the recommended charge-pump capacitor connections. Do not treat the internal ESD protection as a substitute for a properly designed external surge-protection network when cables leave the enclosure.

This page combines device specifications, same-footprint drop-in alternatives, pin-level guidance, and application-focused design notes. It also highlights the MAX3384EEAP's balance of 3V supply operation, 250kbps throughput, low-power features, and enhanced IEC 1000-4-2 ESD protection for engineers evaluating a modern single-supply RS-232 interface.

Alternativas directas para MAX3384EEAP — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.

Variantes de esta serie

Modelos de la misma serie compatibles directamente con MAX3384EEAP (mismo factor de forma y huella) — difiere en Maximum Data Rate, Package Type, Supply Voltage Range.

Analog Devices
Maximum Data Rate: 250kbps
Package Type: SSOP-20
Supply Voltage Range: 3.0V to 5.5V
Comparar con MAX3384EEAP →

MAX3384ECWN+

✅ Sustitución directa
Analog Devices
📦 SSOP-20
RS-232 · Transceiver · 2/2 · 3.0V to 5.5V · 250kbps · 2 · 2 · EIA/TIA-232 and V.28/V.24

Consulte el precio

Ver hoja de datos →

MAX3384ECAP+

✅ Sustitución directa
📦 SSOP-20
Same MAX3384E family and 20-pin SSOP footprint; MAX3384ECAP+ is the commercial-temperature ordering option versus MAX3384EEAP

📋 Alternativa de referencia (no en el catálogo)

MAX3384EAP

✅ Sustitución directa ⚠️ Especificaciones sin verificar
📦 SSOP-20
Same MAX3384E family, 20-pin SSOP footprint, 3 V to 5.5 V supply range, and 250kbps capability; ordering suffix and temperature grade differ

📋 Alternativa de referencia (no en el catálogo)

MAX3384EEAP+

✅ Sustitución directa ⚠️ Especificaciones sin verificar
📦 SSOP-20
Same electrical configuration and 20-pin SSOP footprint as MAX3384EEAP; ordering-code suffix differs without changing the principal supply or data-rate ratings

📋 Alternativa de referencia (no en el catálogo)

ST3384EBPR

✅ Sustitución directa
📦 SSOP-20
Cross-brand 3 V to 5.5 V RS-232 transceiver rated to 250kbps with 1 µA low-power operation; control-pin behavior and temperature grade require confirmation

📋 Alternativa de referencia (no en el catálogo)

MAX3384EEAP Especificaciones

Product Type RS-232 transceiver, 2 drivers and 2 receivers
Interface Standard EIA/TIA-232, V.28 and V.24
Supply Voltage Range 3 V to 5.5 V
Typical Supply Voltage 3.3 V
Maximum Data Rate 250 kbps
Number of Drivers 2
Number of Receivers 2
Duplex Mode Full duplex
Transmitter ESD Protection, Air Gap ±15 kV per IEC 1000-4-2
Receiver ESD Protection, Air Gap ±15 kV per IEC 1000-4-2
Transmitter ESD Protection, Contact ±8 kV per IEC 1000-4-2
Receiver ESD Protection, Contact ±8 kV per IEC 1000-4-2
Low-Power Current 1 µA
Rango de temperatura de funcionamiento 0 °C to +70 °C
Package Type SSOP-20, 5.30 mm, 0.65 mm pitch
Tipo de montaje Surface mount
Número de pines 20

Guía de configuración de pines de MAX3384EEAP ssop-20, 5.30 mm, 0.65 mm pitch

Configuración de pines para MAX3384EEAP (encapsulado ssop-20, 5.30 mm, 0.65 mm pitch). La numeración de pines, las funciones y los diagramas de conexión se definen en la hoja de datos del fabricante. Consúltela para conocer el footprint exacto y las directrices de soldadura.

Diagrama de patillaje del encapsulado ssop-20, 5.30 mm, 0.65 mm pitch para MAX3384EEAP

No hay datos detallados de patillaje disponibles para MAX3384EEAP.

Consulte la hoja de datos para ver la configuración completa de patillas.

Aplicaciones típicas

MAX3384EEAP es adecuado para 6 aplicacións: Industrial Serial Console Interface, Point-of-Sale Terminal Connectivity, Data-Acquisition Equipment Control Port, Test and Measurement Instrument, Embedded Service and Configuration Port, Industrial Automation and Robotics.

🏭

Industrial Serial Console Interface

The MAX3384EEAP fits a 3.3V industrial controller that requires a legacy RS-232 service port for configuration, diagnostics, or firmware recovery. Its 3 V to 5.5 V supply range removes the need for a negative rail, while the 250kbps capability provides ample UART headroom for typical console traffic. The ±15kV IEC 1000-4-2 air-gap and ±8kV contact protection ratings improve resilience when an operator connects a cable in a workshop environment. Place the transceiver close to the connector and route protected signals to the UART pins to minimize pickup before the ESD structures act.

💳

Point-of-Sale Terminal Connectivity

A point-of-sale terminal can use the MAX3384EEAP to connect a compact peripheral over a full-duplex RS-232 port without adding a separate negative supply. The 20-pin SSOP package preserves board area, and operation from a 3.3V rail supports space-constrained embedded platforms. A maximum data rate of 250kbps is more than sufficient for receipt printers, scanners, and payment accessories using conventional UART framing. The internal ESD protection is useful near user-accessible connectors, while external surge elements remain appropriate where the attached cable crosses an industrial power boundary.

📟

Data-Acquisition Equipment Control Port

The MAX3384EEAP is well suited to a data-acquisition unit that combines a 3.3V control processor with instruments using older RS-232 protocols. Two drivers and two receivers permit simultaneous transmit and receive activity, including hardware flow-control signals. The 250kbps rate supports legacy V.28 and V.24 equipment while keeping the interface electrically compatible with modern UART peripherals. Because the IC generates its own bipolar drive voltage, the instrument can retain a conventional RS-232 port without requiring a separate negative power rail or an external level shifter.

🖥️

Test and Measurement Instrument

In a bench instrument, the MAX3384EEAP can provide a compact remote-control connection between a 3.3V controller and an external RS-232 terminal or legacy peripheral. The commercial 0 °C to +70 °C range covers typical laboratory and indoor industrial environments. The 250kbps maximum rate allows the controller to exchange commands, status data, and calibration results over one full-duplex link. Position the device near the rear-panel connector so the protected internal circuitry handles transient energy before it reaches the transceiver, and add external protection if the instrument shares a chassis with high-energy switching circuits.

🧩

Embedded Service and Configuration Port

The MAX3384EEAP can add a field-service connection to an embedded controller that otherwise exposes only USB or Ethernet. Its dual-driver, dual-receiver arrangement supports full-duplex command and response traffic, and the 250kbps rate is suitable for boot logs, configuration files, and remote diagnostics. Running from 3 V to 5.5 V lets the design share the controller's existing supply, while the low-power operating characteristics assist designs that spend significant time in low-power states. Use the manufacturer shutdown and enable guidance when the port must be isolated during normal operation.

🤖

Industrial Automation and Robotics

The MAX3384EEAP can bridge a 3.3V robot controller to older RS-232 programming consoles, sensors, or service tools. Its enhanced ESD protection is valuable in environments where cables are repeatedly connected near motors and switching devices, while the 250kbps throughput matches typical command-response protocols. The 20-pin SSOP footprint supports compact control boards without introducing a second supply rail. For permanent cable runs outside an enclosure, combine the device with a connector-side surge protector and route the interface through a grounded chassis region to reduce common-mode transients.

Resumen de productos recomendados

MC1489NE4 Texas Instruments Se usa en: Industrial Serial Console Interface, Industrial Automation and Robotics DS90C387VJD-TI Texas Instruments Se usa en: Industrial Serial Console Interface, Point-of-Sale Terminal Connectivity TS320IDR Low-power digital interface companion for embedded control Se usa en: Point-of-Sale Terminal Connectivity, Embedded Service and Configuration Port TS974IDT STMicroelectronics Se usa en: Data-Acquisition Equipment Control Port MC74F243M onsemi Se usa en: Data-Acquisition Equipment Control Port, Test and Measurement Instrument DS90CF562VJD High-speed interface companion for control backplanes Se usa en: Test and Measurement Instrument R5F104PN Low-power MCU option for embedded service controllers Se usa en: Embedded Service and Configuration Port MC1488NE4 Texas Instruments Se usa en: Industrial Automation and Robotics
What is the MAX3384EEAP used for?
The MAX3384EEAP is a dual-driver, dual-receiver EIA/TIA-232 transceiver for full-duplex serial communication. It converts CMOS-compatible UART logic into RS-232 levels and converts incoming RS-232 signals back to logic levels. The Analog Devices product page identifies it as a 3V-powered V.28/V.24 communications interface with low-power operation, high data-rate capability, and enhanced ESD protection.
What is the operating voltage of MAX3384EEAP?
The MAX3384EEAP operates from 3 V to 5.5 V and is commonly used at 3.3 V. According to the MAX3384E manufacturer datasheet, its single-supply charge-pump architecture generates the voltage swing needed by the RS-232 drivers without requiring a separate negative supply. This makes the device suitable for both 3.3V and 5V embedded systems.
What is the maximum data rate of MAX3384EEAP?
The MAX3384EEAP supports data rates up to 250kbps. The manufacturer describes the MAX3384E as a high-data-rate EIA/TIA-232 and V.28/V.24 interface. This rate is well above the throughput of many legacy serial peripherals while remaining suitable for UART-based configuration links, industrial consoles, and embedded service interfaces.
Where can I download the MAX3384EEAP datasheet PDF?
The official MAX3384E datasheet and product information are available from the Analog Devices product page at https://www.analog.com/en/products/max3384e.html. The device data also appears as an 11-page MAX3384EEAP datasheet document. Use the manufacturer's pin-description table and application information when assigning PCB nets and selecting external charge-pump and bypass capacitors.
Where can I find the MAX3384EEAP pinout?
The MAX3384EEAP uses a 20-pin SSOP package with 0.65mm pitch and a nominal body width of 5.30mm. Use the pin-description table in the MAX3384E manufacturer datasheet to assign transmitter inputs, receiver outputs, supply pins, ground connections, and shutdown control. Request the complete pin-assignment PDF through the Request a Quote form on this page if a copy of the manufacturer document is required.
What ESD protection does MAX3384EEAP provide?
All MAX3384EEAP transmitter outputs and receiver inputs are protected against ESD discharge. The manufacturer specifies ±15kV using the IEC 1000-4-2 air-gap discharge method and ±8kV using the IEC 1000-4-2 contact-discharge method. These internal protections improve robustness, although external protection may still be needed for severe industrial surge conditions or long cable runs.
How does the MAX3384EEAP compare with MAX3384ECWN+?
The MAX3384ECWN+ is identified as a complete replacement for the MAX3384EEAP because its terminals, package, main performance parameters, and functional characteristics are consistent. Both devices are 20-pin RS-232 transceivers from the same MAX3384E family. Review the ordering information and temperature grade in the manufacturer documentation before transferring a production design.
Can ST3384EBPR replace MAX3384EEAP?
The ST3384EBPR can serve as an RS-232 replacement candidate with a 3 V to 5.5 V supply, low-power operation, and 250kbps data-rate capability. The cross-reference identifies it as a replacement for MAX3384EEAP, but a board revision should confirm the exact SSOP-20 lead assignments, receiver logic behavior, shutdown configuration, and ESD ratings before production use.
When should I choose MAX3384EEAP over MAX3323EEUE+T?
Choose the MAX3384EEAP when you need a 3V-powered, 250kbps-capable RS-232 interface with enhanced ESD protection. The MAX3323EEUE+T is appropriate when its lower-power operating characteristics and supply-voltage arrangement better match the design. The cross-reference comparison identifies differences in package and performance attributes, so compare the complete electrical tables rather than treating the parts as automatically interchangeable.
Is MAX3384EEAP suitable for a 3.3V industrial controller?
Yes, the MAX3384EEAP is suitable for a 3.3V controller because it operates from 3 V to 5.5 V and is rated for 0 °C to +70 °C. Its 250kbps limit comfortably supports many service and configuration ports. For installations with conducted noise or severe surge exposure, add connector-side protection and verify that the enclosure and cable length keep transient levels within the device ratings.
What can replace the MAX3384EEAP?
The MAX3384ECWN+ is the closest same-family drop-in option because the cross-reference describes its terminals, package, and functional characteristics as consistent with the MAX3384EEAP. The ST3384EBPR is a cross-brand replacement candidate with matching 3 V to 5.5 V operation and 250kbps capability. Both options require checking the exact lead mapping, temperature range, and control-pin behavior.
What are the key specifications of MAX3384EEAP that engineers should know?
The key MAX3384EEAP specifications are a 3 V to 5.5 V supply range, dual-driver and dual-receiver configuration, full-duplex RS-232 operation, and a maximum signaling rate of 250kbps. The MAX3384E also provides ±15kV IEC 1000-4-2 air-gap and ±8kV contact ESD protection, a 20-pin 0.65mm-pitch SSOP package, and a 0 °C to +70 °C commercial operating range.
Where can I buy MAX3384EEAP online?
Use the Request a Quote form on this page to request MAX3384EEAP availability, current lead time, and order quantities from XAIPART. The part is a 20-SSOP RS-232 full-duplex transceiver from Analog Devices, and the form connects your request directly with the supply team for an orderable quotation.
What is the price of MAX3384EEAP?
Current MAX3384EEAP pricing is handled through the Request a Quote form on this page so the quotation reflects the requested quantity, date, and supply conditions. The component is a 20-SSOP, 2/2 full-duplex RS-232 transceiver rated for 250kbps operation. Submit the quote request with your production volume and target schedule for a direct response.
Is MAX3384EEAP in stock and what is its lead time?
Request current MAX3384EEAP inventory status and lead time through the Request a Quote form on this page. Supply availability can vary with order volume and procurement timing, so a quotation provides the most actionable confirmation for production planning. The requested configuration is the 20-pin SSOP, 2-driver, 2-receiver RS-232 transceiver.

Datos de referencia de ingeniería para MAX3384EEAP — comparación, orientación de diseño e información de cumplimiento.

Guía de selección

Choose the MAX3384EEAP when a compact system needs a complete full-duplex RS-232 port from a 3.3V or 5V supply and benefits from specified IEC 1000-4-2 ESD protection. MAX3384ECWN+ is the preferred same-family drop-in when the cross-reference confirms consistent terminals, package, and functional characteristics; verify its ordering code and temperature grade before release. MAX3384ECAP+ provides another same-family 20-SSOP option, while MAX3384EAP and MAX3384EEAP+ can cover ordering-code differences within the MAX3384E family. Consider the ST3384EBPR only after checking every lead assignment, control-pin polarity, temperature range, and ESD test condition. For a design needing only one direction or a lower data rate, a less integrated driver or receiver may reduce cost and board area, but it will not provide the same drop-in interface.

Comparación con alternativas

Parámetro Este producto MAX3384ECWN+ MAX3384ECAP+ MAX3384EAP MAX3384EEAP+ ST3384EBPR
Package SSOP-20, 5.30 mm, 0.65 mm pitch SSOP-20 SSOP-20 SSOP-20 SSOP-20 SSOP-20
Brand Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices STMicroelectronics
Device Type 2/2 full-duplex RS-232 transceiver RS-232 transceiver RS-232 transceiver RS-232 transceiver RS-232 transceiver RS-232 transceiver
Supply Voltage Range 3 V to 5.5 V 3 V to 5.5 V 3 V to 5.5 V 3 V to 5.5 V 3 V to 5.5 V 3 V to 5.5 V
Maximum Data Rate 250 kbps 250 kbps 250 kbps 250 kbps 250 kbps 250 kbps
Low-Power Current 1 µA 1 µA 1 µA 1 µA 1 µA 1 µA
Air-Gap ESD Protection ±15 kV per IEC 1000-4-2 ±15 kV per IEC 1000-4-2 ±15 kV per IEC 1000-4-2 ±15 kV per IEC 1000-4-2 ±15 kV per IEC 1000-4-2 15 kV ESD protected
Contact ESD Protection ±8 kV per IEC 1000-4-2 ±8 kV per IEC 1000-4-2 ±8 kV per IEC 1000-4-2 ±8 kV per IEC 1000-4-2 ±8 kV per IEC 1000-4-2 15 kV ESD protected

Diferenciadores clave

  • Single low-voltage supply for a complete RS-232 port (frente a MAX3323EEUE+T)
  • ESD protection on every driver output and receiver input (frente a ST3384EBPR)
  • Higher signaling throughput within the same legacy interface (frente a MC1489NE4)

Notas de diseño

Place the MAX3384EEAP close to the RS-232 connector and keep the driver outputs and receiver inputs on short traces. Connect the charge-pump capacitors and supply bypass components exactly as shown in the manufacturer application circuit. Keeping switching-capacitor nodes compact reduces radiated emissions and prevents external interference from coupling into the receiver path.

RS-232 cables can pick up external noise when they leave an enclosure, particularly when routed near motor, relay, or switching-power circuits. Use a shielded cable with a chassis-connected shell, maintain a ground reference between systems, and add a connector-side transient-protection device if the installation is exposed to severe surge conditions. The IC's ±15kV air-gap ESD rating protects sensitive pins but does not replace surge-energy coordination.

Do not substitute a logic-level TTL or RS-485 transceiver for the MAX3384EEAP without rechecking pinout and signal polarity. Confirm the shutdown behavior, receiver enable polarity, and flow-control assignments against the manufacturer pin-description table before PCB release. Also verify that the UART baud rate remains well below the 250kbps device limit after accounting for framing, parity, and software overhead.

Información de cumplimiento

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Libre de plomo
Unknown
Libre de halógenos
Unknown
Minerales en conflicto
Unknown

The MAX3384EEAP is a commercial-temperature RS-232 interface for general-purpose industrial and instrumentation use. IEC 1000-4-2 ESD test methods are specified for the device, but RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations require confirmation from the manufacturer product documentation.

Datos verificados el: 2026-11-09 — datos verificados y seleccionados por el equipo de ingeniería de componentes de XAIPART

Búsquedas relacionadas

MAX3384EEAP datasheet MAX3384EEAP pinout MAX3384EEAP datasheet pdf MAX3384EEAP SSOP-20 MAX3384EEAP equivalent MAX3384EEAP drop-in replacement MAX3384EEAP vs MAX3384ECWN+ MAX3384EEAP vs ST3384EBPR Analog Devices MAX3384EEAP MAX3384EEAP 3V RS-232 transceiver MAX3384EEAP 250kbps interface MAX3384EEAP price MAX3384EEAP stock MAX3384EEAP application circuit MAX3384EEAP ESD protection

Componentes & términos relacionados

Analog Devices MAX3384EEAP MAX3384E MAX3384ECWN+ MAX3384ECAP+ MAX3384EAP MAX3384EEAP+ ST3384EBPR RS-232 transceiver EIA/TIA-232 V.28 V.24 UART full-duplex communications charge-pump voltage converter electrostatic discharge protection IEC 1000-4-2 SSOP-20 surface-mount package 250kbps data rate 3.3V power supply industrial serial interface legacy serial communication RS-232 driver RS-232 receiver
RFQ de presupuesto rápido
Complete los detalles — nuestro equipo de ventas responderá en un plazo de 24 horas
Número de pieza Fabricante Encapsulado QTY Precio objetivo Total
✓
¡Presupuesto enviado!

Responderemos a su correo electrónico en un plazo de 24 horas

1
RFQ enviado
2
Presupuesto recibido
3
Pedido realizado
4
Pago
5
Enviado
6
Entregado
Ver detalles del RFQ