MAX3384EEAP - 3V RS-232 Transceiver, 250kbps | Analog Devices
MPN: MAX3384EEAP ✓ فعالMAX3384EEAP جائزہ
An RS-232 transceiver is an interface IC that converts logic-level UART signals into RS-232 bipolar levels and converts received RS-232 levels back into CMOS-compatible logic. The MAX3384EEAP belongs to the interface IC hierarchy alongside serial transceivers, line drivers, and level-shifting ICs. Its two-driver, two-receiver arrangement supports full-duplex point-to-point communication, including flow-control lines between two data-terminal systems.
Key features include a 3V to 5.5V supply range, operation up to 250kbps, low-power operation with shutdown and receiver active-low features, and ±15kV air-gap ESD protection on all transmitter outputs and receiver inputs. Contact discharge protection is rated at ±8kV using the IEC 1000-4-2 test method. These protection levels are important when the connector is exposed to cable discharge events or an industrial noise environment.
The MAX3384E uses charge-pump circuitry to generate the bipolar voltage required by the RS-232 drivers, allowing operation from a single low-voltage supply. This architecture eliminates the need for a separate negative supply rail. The resulting single-supply implementation reduces board complexity in systems that already operate from 3.3V or 5V, while the driver stage provides the voltage swing expected by RS-232 receivers.
Typical applications include industrial serial consoles, point-of-sale terminals, data-acquisition equipment, instrument control links, and embedded systems that communicate with legacy RS-232 peripherals. The 250kbps maximum data rate supports modern UART traffic while remaining compatible with the slower signaling commonly used by V.28 and V.24 equipment. The package is also suitable for compact control boards where connector access is limited.
When laying out the circuit, place the device close to the RS-232 connector to minimize the length of unprotected traces between the IC and connector. Follow the pin-description and decoupling guidance in the manufacturer datasheet, and maintain the recommended charge-pump capacitor connections. Do not treat the internal ESD protection as a substitute for a properly designed external surge-protection network when cables leave the enclosure.
This page combines device specifications, same-footprint drop-in alternatives, pin-level guidance, and application-focused design notes. It also highlights the MAX3384EEAP's balance of 3V supply operation, 250kbps throughput, low-power features, and enhanced IEC 1000-4-2 ESD protection for engineers evaluating a modern single-supply RS-232 interface.
کے لیے ڈراپ اِن متبادل MAX3384EEAP — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں MAX3384EEAP (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Maximum Data Rate, Package Type, Supply Voltage Range.
MAX3384ECWN+
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →MAX3384ECAP+
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
MAX3384EAP
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہ📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
MAX3384EEAP+
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہ📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
ST3384EBPR
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
MAX3384EEAP تفصیلات
| Product Type | RS-232 transceiver, 2 drivers and 2 receivers |
| Interface Standard | EIA/TIA-232, V.28 and V.24 |
| Supply Voltage Range | 3 V to 5.5 V |
| Typical Supply Voltage | 3.3 V |
| Maximum Data Rate | 250 kbps |
| Number of Drivers | 2 |
| Number of Receivers | 2 |
| Duplex Mode | Full duplex |
| Transmitter ESD Protection, Air Gap | ±15 kV per IEC 1000-4-2 |
| Receiver ESD Protection, Air Gap | ±15 kV per IEC 1000-4-2 |
| Transmitter ESD Protection, Contact | ±8 kV per IEC 1000-4-2 |
| Receiver ESD Protection, Contact | ±8 kV per IEC 1000-4-2 |
| Low-Power Current | 1 µA |
| آپریٹنگ درجہ حرارت رینج | 0 °C to +70 °C |
| Package Type | SSOP-20, 5.30 mm, 0.65 mm pitch |
| ماؤنٹنگ ٹائپ | Surface mount |
| پنز کی تعداد | 20 |
MAX3384EEAP ssop-20, 5.30 mm, 0.65 mm pitch پن کنفیگریشن گائیڈ
MAX3384EEAP (ssop-20, 5.30 mm, 0.65 mm pitch پیکیج) کے لیے پن کنفیگریشن۔ پن نمبرنگ، فنکشنز اور کنکشن ڈایاگرامز مینوفیکچرر کے ڈیٹا شیٹ میں بیان کیے گئے ہیں۔ درست فٹ پرنٹ اور سولڈرنگ رہنما ہدایات کے لیے اسی سے رجوع کریں۔
کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں MAX3384EEAP.
رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔
عام استعمالات
MAX3384EEAP کے لیے موزوں ہے 6 ایپلیکیشنs: Industrial Serial Console Interface, Point-of-Sale Terminal Connectivity, Data-Acquisition Equipment Control Port, Test and Measurement Instrument, Embedded Service and Configuration Port, Industrial Automation and Robotics.
Industrial Serial Console Interface
The MAX3384EEAP fits a 3.3V industrial controller that requires a legacy RS-232 service port for configuration, diagnostics, or firmware recovery. Its 3 V to 5.5 V supply range removes the need for a negative rail, while the 250kbps capability provides ample UART headroom for typical console traffic. The ±15kV IEC 1000-4-2 air-gap and ±8kV contact protection ratings improve resilience when an operator connects a cable in a workshop environment. Place the transceiver close to the connector and route protected signals to the UART pins to minimize pickup before the ESD structures act.
تجویز کردہ
Point-of-Sale Terminal Connectivity
A point-of-sale terminal can use the MAX3384EEAP to connect a compact peripheral over a full-duplex RS-232 port without adding a separate negative supply. The 20-pin SSOP package preserves board area, and operation from a 3.3V rail supports space-constrained embedded platforms. A maximum data rate of 250kbps is more than sufficient for receipt printers, scanners, and payment accessories using conventional UART framing. The internal ESD protection is useful near user-accessible connectors, while external surge elements remain appropriate where the attached cable crosses an industrial power boundary.
تجویز کردہ
Data-Acquisition Equipment Control Port
The MAX3384EEAP is well suited to a data-acquisition unit that combines a 3.3V control processor with instruments using older RS-232 protocols. Two drivers and two receivers permit simultaneous transmit and receive activity, including hardware flow-control signals. The 250kbps rate supports legacy V.28 and V.24 equipment while keeping the interface electrically compatible with modern UART peripherals. Because the IC generates its own bipolar drive voltage, the instrument can retain a conventional RS-232 port without requiring a separate negative power rail or an external level shifter.
تجویز کردہ
Test and Measurement Instrument
In a bench instrument, the MAX3384EEAP can provide a compact remote-control connection between a 3.3V controller and an external RS-232 terminal or legacy peripheral. The commercial 0 °C to +70 °C range covers typical laboratory and indoor industrial environments. The 250kbps maximum rate allows the controller to exchange commands, status data, and calibration results over one full-duplex link. Position the device near the rear-panel connector so the protected internal circuitry handles transient energy before it reaches the transceiver, and add external protection if the instrument shares a chassis with high-energy switching circuits.
تجویز کردہ
Embedded Service and Configuration Port
The MAX3384EEAP can add a field-service connection to an embedded controller that otherwise exposes only USB or Ethernet. Its dual-driver, dual-receiver arrangement supports full-duplex command and response traffic, and the 250kbps rate is suitable for boot logs, configuration files, and remote diagnostics. Running from 3 V to 5.5 V lets the design share the controller's existing supply, while the low-power operating characteristics assist designs that spend significant time in low-power states. Use the manufacturer shutdown and enable guidance when the port must be isolated during normal operation.
تجویز کردہ
Industrial Automation and Robotics
The MAX3384EEAP can bridge a 3.3V robot controller to older RS-232 programming consoles, sensors, or service tools. Its enhanced ESD protection is valuable in environments where cables are repeatedly connected near motors and switching devices, while the 250kbps throughput matches typical command-response protocols. The 20-pin SSOP footprint supports compact control boards without introducing a second supply rail. For permanent cable runs outside an enclosure, combine the device with a connector-side surge protector and route the interface through a grounded chassis region to reduce common-mode transients.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا MAX3384EEAP — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | MAX3384ECWN+ | MAX3384ECAP+ | MAX3384EAP | MAX3384EEAP+ | ST3384EBPR |
|---|---|---|---|---|---|---|
| Package | SSOP-20, 5.30 mm, 0.65 mm pitch | SSOP-20 | SSOP-20 | SSOP-20 | SSOP-20 | SSOP-20 |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | STMicroelectronics |
| Device Type | 2/2 full-duplex RS-232 transceiver | RS-232 transceiver | RS-232 transceiver | RS-232 transceiver | RS-232 transceiver | RS-232 transceiver |
| Supply Voltage Range | 3 V to 5.5 V | 3 V to 5.5 V | 3 V to 5.5 V | 3 V to 5.5 V | 3 V to 5.5 V | 3 V to 5.5 V |
| Maximum Data Rate | 250 kbps | 250 kbps | 250 kbps | 250 kbps | 250 kbps | 250 kbps |
| Low-Power Current | 1 µA | 1 µA | 1 µA | 1 µA | 1 µA | 1 µA |
| Air-Gap ESD Protection | ±15 kV per IEC 1000-4-2 | ±15 kV per IEC 1000-4-2 | ±15 kV per IEC 1000-4-2 | ±15 kV per IEC 1000-4-2 | ±15 kV per IEC 1000-4-2 | 15 kV ESD protected |
| Contact ESD Protection | ±8 kV per IEC 1000-4-2 | ±8 kV per IEC 1000-4-2 | ±8 kV per IEC 1000-4-2 | ±8 kV per IEC 1000-4-2 | ±8 kV per IEC 1000-4-2 | 15 kV ESD protected |
اہم امتیازی خصوصیات
- Single low-voltage supply for a complete RS-232 port (بمقابلہMAX3323EEUE+T)
- ESD protection on every driver output and receiver input (بمقابلہST3384EBPR)
- Higher signaling throughput within the same legacy interface (بمقابلہMC1489NE4)
ڈیزائن نوٹس
Place the MAX3384EEAP close to the RS-232 connector and keep the driver outputs and receiver inputs on short traces. Connect the charge-pump capacitors and supply bypass components exactly as shown in the manufacturer application circuit. Keeping switching-capacitor nodes compact reduces radiated emissions and prevents external interference from coupling into the receiver path.
RS-232 cables can pick up external noise when they leave an enclosure, particularly when routed near motor, relay, or switching-power circuits. Use a shielded cable with a chassis-connected shell, maintain a ground reference between systems, and add a connector-side transient-protection device if the installation is exposed to severe surge conditions. The IC's ±15kV air-gap ESD rating protects sensitive pins but does not replace surge-energy coordination.
Do not substitute a logic-level TTL or RS-485 transceiver for the MAX3384EEAP without rechecking pinout and signal polarity. Confirm the shutdown behavior, receiver enable polarity, and flow-control assignments against the manufacturer pin-description table before PCB release. Also verify that the UART baud rate remains well below the 250kbps device limit after accounting for framing, parity, and software overhead.
تعمیل کی معلومات
The MAX3384EEAP is a commercial-temperature RS-232 interface for general-purpose industrial and instrumentation use. IEC 1000-4-2 ESD test methods are specified for the device, but RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations require confirmation from the manufacturer product documentation.