MC33272AP - Dual 24 MHz Low-Offset Op Amp | onsemi
N.º de pieza: MC33272AP ✓ ActivoMC33272AP Descripción general
An operational amplifier is a voltage-controlled differential amplifier whose inverting and non-inverting inputs are compared to produce an amplified output. Within the amplifier hierarchy, the MC33272AP belongs to the bipolar operational-amplifier family and provides a general-purpose combination of precision input characteristics, wide bandwidth, and high slew rate. It is a voltage-feedback device suitable for signal conditioning, feedback control, analog signal processing, and test equipment.
The primary performance features include a 24 MHz gain-bandwidth product, 10 V/µs slew rate, and low input-offset voltage. These characteristics allow the device to handle signals extending well beyond audio-band requirements while retaining the low-offset behavior sought in instrumentation and feedback applications. Wide operating-voltage support also permits use in industrial systems operating from 3 V through 36 V, subject to the absolute maximum ratings and common-mode limitations specified by the manufacturer.
The bipolar input architecture and patented Zip-R-Trim element distinguish the MC33272 from simpler general-purpose amplifiers. Input-offset adjustment improves matching between closely related amplifier channels, which is useful in differential measurement paths where offset error can otherwise become a significant part of the total error budget. The dual-doublet frequency-compensation architecture supports stable operation in typical feedback networks without requiring the precision associated with more specialized instrumentation amplifiers.
Typical uses include low-level sensor conditioning, current-loop receivers, active filters, audio and communication-signal stages, sample-and-hold buffers, and laboratory control circuits. The 10 V/µs slew rate is particularly useful for waveform and pulse paths, while the 24 MHz bandwidth allows the amplifier to operate effectively above audio frequencies. In closed-loop designs, actual bandwidth depends on the selected noise gain, feedback network, load, and device stability requirements.
When designing an MC33272AP circuit, verify common-mode input range, output swing, output-current capability, and noise-gain stability against the manufacturer datasheet for the actual supply voltage. Keep feedback traces short, place compensation or decoupling components close to the relevant pins, and avoid loading the output beyond its specified limits. Input-bias-current errors and resistor-generated noise should also be included in the overall accuracy calculation.
This page combines manufacturer specifications, package details, drop-in alternatives, application guidance, and parameter-by-parameter engineering comparisons. It is structured to help engineers identify the appropriate replacement, plan the PCB footprint, and evaluate whether the 24 MHz bandwidth and 10 V/µs slew rate meet the requirements of a particular analog signal chain.
Alternativas directas para MC33272AP — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
MC33272AD
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
MC33272CP
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
MC33272CD
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
LM6172AN
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
TLE2072CP
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
OPA2134PA
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
AD826ANZ
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
MC33272AP Valores máximos y características eléctricas
| Amplifier Type | Dual general-purpose operational amplifier |
| Number of Amplifier Circuits | 2 circuits |
| Gain-Bandwidth Product | 24 MHz |
| Slew Rate | 10 V/µs |
| Supply Voltage Range | 3 V to 36 V |
| Input Offset Voltage | 50 µV maximum |
| Input Architecture | Bipolar input |
| Offset Adjustment Technology | Patented Zip-R-Trim element |
| Compensation Architecture | Dual-doublet frequency compensation |
| Encapsulado | 8-pin plastic DIP, 0.300 inch (7.62 mm) pitch |
| Tipo de montaje | Through-hole |
Configuración de pines de MC33272AP
| Pin 1 | OUTPUT A — Amplifier A output |
| Pin 2 | INPUT A- — Inverting input for amplifier A |
| Pin 3 | INPUT A+ — Non-inverting input for amplifier A |
| Pin 4 | V- — Negative supply connection |
| Pin 5 | INPUT B+ — Non-inverting input for amplifier B |
| Pin 6 | INPUT B- — Inverting input for amplifier B |
| Pin 7 | OUTPUT B — Amplifier B output |
| Pin 8 | V+ — Positive supply connection |
Aplicaciones típicas
MC33272AP es adecuado para 6 aplicacións: Precision Sensor Signal Conditioning, Industrial Current Measurement, Active Filter Design, Audio and Communications Conditioning, Pulse and Waveform Amplification, Laboratory and Test Equipment.
Precision Sensor Signal Conditioning
The MC33272AP fits low-level sensor front ends where its 50 µV maximum input-offset voltage and 24 MHz gain-bandwidth product provide a useful balance of accuracy and bandwidth. Place the amplifier in a non-inverting configuration to preserve the sensor signal while providing stable gain, or use an inverting configuration when signal inversion is required. The 10 V/µs slew rate supports signals beyond the audio band, although input-bias-current error, resistor noise, and common-mode limits must be included in the accuracy budget. Verify the sensor output range against the amplifier’s common-mode input range before finalizing the gain network.
Recomendado
Industrial Current Measurement
The MC33272AP can form the analog gain stage of a current-measurement path when the shunt voltage is small and signal accuracy is important. Its 50 µV maximum input offset helps limit the error introduced near the measurement floor, while 24 MHz bandwidth supports faster current-loop signals and transient detection. A shunt amplifier such as INA240A1PW may be preferred when common-mode rejection and bidirectional current sensing are the primary requirements. If the MC33272AP is used instead, account for input-bias-current effects, shunt resistance, Kelvin routing, and the output range at the chosen supply voltage.
Recomendado
Active Filter Design
The MC33272AP is appropriate for second-order active filters that combine moderate precision with useful high-frequency capability. Its 24 MHz gain-bandwidth product and 10 V/µs slew rate provide margin for filter gain and signal-frequency requirements, while the low-offset architecture helps preserve low-level filter responses. Component tolerances and the amplifier’s finite gain and output limits should be included in the transfer-function analysis. Verify stability at the intended noise gain and check the maximum signal amplitude so that the output does not approach the supply rails.
Recomendado
Audio and Communications Conditioning
The MC33272AP can amplify audio-frequency, control, or communications signals in equipment where the 24 MHz bandwidth exceeds the signal bandwidth and the 10 V/µs slew rate provides clean response to transients. Its dual configuration allows one package to handle two related signal paths, such as a receive channel and an auxiliary monitor channel. The bipolar input stage should be evaluated for bias-current-induced DC error when the source impedance is high. Keep feedback and input routing compact, provide suitable output loading, and confirm the output-voltage swing before operating near the supply limits.
Recomendado
Pulse and Waveform Amplification
The 10 V/µs slew rate makes the MC33272AP useful for amplifying moderate-amplitude pulse and waveform signals without requiring the very high bandwidth of a dedicated video amplifier. The 24 MHz gain-bandwidth product supports closed-loop gains below unity while providing more bandwidth than audio-only amplifiers. For instrumentation applications, examine the output-current capability and capacitive-load behavior of the selected circuit. Rising-edge fidelity depends not only on slew rate but also on small-signal bandwidth, feedback impedance, source resistance, and the exact output amplitude.
Recomendado
Laboratory and Test Equipment
The MC33272AP can serve as a general-purpose dual amplifier in laboratory buffers, programmable gain stages, and feedback-control circuits. Its low maximum input-offset voltage supports measurements where the signal is close to the input range of the instrument, while the dual package offers independent channels for differential or multi-stage arrangements. Use the exact manufacturer ordering information to select the required temperature grade. Calibration routines should include input-offset voltage, bias-current effects, and output-offset drift, particularly when the source impedance is high.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para MC33272AP — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | MC33272AD | LM6172AN | TLE2072CP | OPA2134PA | AD826ANZ |
|---|---|---|---|---|---|---|
| Brand | onsemi | onsemi | Texas Instruments | Texas Instruments | Texas Instruments | Analog Devices |
| Package | 8-PDIP (0.300 inch, 7.62 mm) | 8-PDIP (0.300 inch, 7.62 mm) | 8-PDIP (0.300 inch, 7.62 mm) | 8-PDIP (0.300 inch, 7.62 mm) | 8-PDIP (0.300 inch, 7.62 mm) | 8-PDIP (0.300 inch, 7.62 mm) |
| Amplifier Count | 2 | 2 | 2 | 2 | 2 | 2 |
| Gain-Bandwidth Product | 24 MHz | 24 MHz | 100 MHz | 10 MHz | 8 MHz | 50 MHz |
| Slew Rate | 10 V/µs | 10 V/µs | 13 V/µs | 35 V/µs | 20 V/µs | 350 V/µs |
| Supply Voltage Range | 3 V to 36 V | 3 V to 36 V | 3 V to 32 V | ±18 V | ±18 V | ±5 V to ±18 V |
| Input Architecture | Bipolar | Bipolar | Bipolar | Bipolar | JFET | Bipolar |
Diferenciadores clave
- Balances precision and bandwidth in a dual DIP package (frente a OPA2134PA)
- Lower bandwidth than the high-speed LM6172AN (frente a LM6172AN)
- Offset-voltage adjustment is integrated into the MC33272A family (frente a AD826ANZ)
Notas de diseño
Do not select the amplifier solely from its 24 MHz gain-bandwidth figure. At a closed-loop gain of 10, the nominal signal bandwidth is approximately 2.4 MHz before the amplifier’s additional pole and closed-loop-response effects are considered. Confirm the required signal amplitude, phase margin, output-current capability, and capacitive-load behavior using the manufacturer’s recommended operating area and stability guidance. A footprint-compatible substitute can behave differently even when its headline bandwidth is higher.
Route the two amplifier channels to minimize feedback-loop area and keep high-impedance input nodes away from output and supply-return currents. Use a solid ground plane, place input-bias-current compensation resistors close to the non-inverting inputs when the source impedance is high, and decouple each supply rail near the IC. Through-hole DIP construction simplifies prototyping, but lead bending and soldering still require care around pins 1 through 8 to avoid package stress.
Evaluate the complete gain-and-frequency response instead of relying on slew rate alone. The 10 V/µs large-signal capability and 24 MHz small-signal bandwidth describe different constraints, and the lower value limits the result for a given signal amplitude and frequency. For sine waves, calculate the maximum amplitude before large-signal distortion dominates; for transient signals, check rise time and settling behavior at the required closed-loop gain.
Single-supply operation requires attention to the signal’s common-mode range and the amplifier’s output swing. Bias the signal around the midpoint of the usable output region when possible, and verify that the output can reach the required load voltage with adequate phase margin. Avoid operating the output near the positive rail or ground when the circuit must preserve waveform symmetry. The manufacturer’s input common-mode and output-swing curves should be checked at the actual supply voltage and load.
Información de cumplimiento
The operational-amplifier category and manufacturer product information do not establish automotive qualification, RoHS, REACH, halogen-free, or conflict-minerals status. Use the current onsemi product declaration or material-compliance documentation for production verification.