MKL26Z64VFT4 - 48MHz Cortex-M0+ 64KB MCU | NXP
N.º de pieza: MKL26Z64VFT4 ✓ ActivoMKL26Z64VFT4 Descripción general
A microcontroller is a programmable semiconductor that integrates a processor core, nonvolatile program memory, data memory, peripherals, and communication interfaces on one device. The MKL26Z64VFT4 belongs to the Kinetis KL2x family, an ultra-low-power MCU family positioned for battery-powered instruments, human-interface devices, industrial controls, and connected accessories. Its USB capability distinguishes it from basic microcontrollers intended only for general embedded control.
Key features include an ARM Cortex-M0+ core, a maximum operating frequency of 48 MHz, 64 KB of flash, and a full-speed USB device controller. The 64 KB of flash provides room for firmware, configuration data, and boot code, while the Cortex-M0+ core supports efficient event-driven control. The specified operating temperature range of -40 °C to +105 °C covers industrial temperature requirements, although the complete electrical limits must be checked against the manufacturer datasheet for the exact suffix and grade.
The MKL26Z64VFT4 uses a 48-QFN 7 mm by 7 mm package, enabling a compact surface-mount layout with short signal paths. USB and general-purpose I/O are particularly useful for data acquisition modules, configuration interfaces, human-interface equipment, and low-power peripherals. Because the device is a microcontroller rather than a fixed-function interface controller, firmware can consolidate protocol handling, control logic, timing, and peripheral coordination into one component.
Typical applications include USB-connected sensors, programmable measurement modules, compact control boards, industrial human-interface terminals, and energy-efficient embedded accessories. In these systems, the 48 MHz processing rate supports responsive control loops, the flash capacity supports moderate application firmware, and the USB device controller can simplify direct connectivity to a host computer or USB interface circuit.
PCB implementation should follow the manufacturer’s QFN land pattern and pin-assignment table. Keep USB routing short, provide the specified power and decoupling network, and route high-current or sensitive analog functions away from digital switching nodes. Confirm oscillator, USB, and I/O requirements for the exact board configuration before releasing the layout.
This page combines the NXP product identity, distributor catalog specifications, package details, application guidance, and same-package family alternatives into a compact engineering reference. It also highlights the decisions that matter when replacing or redesigning around the MKL26Z64VFT4, including core, memory, USB, package, and temperature constraints.
Alternativas directas para MKL26Z64VFT4 — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con MKL26Z64VFT4 (mismo factor de forma y huella) — difiere en Package, Flash Memory, SRAM, Product Family, Product Type.
MKL26Z64VCM4
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
MKL26Z64VFM4
✅ Sustitución directaConsulte el precio
Ver hoja de datos →MKL26Z64VCM4R
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
MKL26Z64VFM4R
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
MKL26Z64VFT4R
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
MKL26Z64VFT4 Valores máximos y características eléctricas
| Product Type | 32-bit ARM Cortex-M0+ microcontroller |
| Product Family | Kinetis KL2 |
| Processor Core | ARM Cortex-M0+ |
| Maximum CPU Frequency | 48 MHz |
| Flash Memory | 64 KB |
| Flash Organization | 64K x 8 bits |
| USB Controller | Full-speed USB 2.0 device controller |
| Rango de temperatura de funcionamiento | -40 °C to +105 °C |
| Package Type | 48-QFN |
| Package Dimensions | 7 mm x 7 mm |
| Tipo de montaje | Surface mount |
| Ancho del bus de datos | 32 bits |
| Estado RoHS | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | unknown |
Guía de configuración de pines de MKL26Z64VFT4 7 mm x 7 mm
Configuración de pines para MKL26Z64VFT4 (encapsulado 7 mm x 7 mm). Este CI digital incluye GPIO, interfaces de comunicación (UART, SPI, I2C) y pines de alimentación. Consulte la hoja de datos del fabricante para conocer las funciones alternativas de los pines y las opciones de configuración. Esencial para el diseño de sistemas embebidos y el diseño de PCB.
No hay datos detallados de patillaje disponibles para MKL26Z64VFT4.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
MKL26Z64VFT4 es adecuado para 6 aplicacións: USB-Connected Sensor Module, Compact Human-Interface Controller, Industrial Data-Acquisition Controller, Battery-Powered Measurement Device, Programmable Automation Controller, USB Field-Service Adapter.
USB-Connected Sensor Module
The MKL26Z64VFT4 fits a USB-connected environmental or industrial sensor because its 48 MHz ARM Cortex-M0+ core can sample inputs, apply calibration, and format data while the full-speed USB device controller provides a direct host interface. Its 64 KB of flash is suitable for moderate sensor firmware, configuration tables, and boot logic. In implementation, keep the USB differential pair routed as a short controlled-impedance pair and provide the power and decoupling network specified by NXP. The main engineering consideration is balancing USB activity against the device’s low-power modes so that sensors do not consume unnecessary energy while maintaining a responsive bus connection.
Recomendado
Compact Human-Interface Controller
The MKL26Z64VFT4 is appropriate for a compact keypad, control panel, or configuration interface that combines USB connectivity with embedded logic. Its Cortex-M0+ core can scan inputs, manage indicators, detect events, and run communication firmware at up to 48 MHz, while 64 KB of flash provides space for application code. The USB device controller allows the panel to enumerate as a direct peripheral rather than requiring a separate USB interface IC. A practical design should debounce mechanical inputs in firmware, define stable LED drive currents, and validate USB signal routing and power behavior against the NXP hardware guidance.
Recomendado
Industrial Data-Acquisition Controller
The MKL26Z64VFT4 can coordinate a small industrial data-acquisition board that combines sensor conditioning, digital control, and USB reporting. Its 48 MHz processing rate provides useful responsiveness for digital filtering and control tasks, and the 64 KB flash capacity supports a structured application rather than a minimal fixed-function controller. The device should be placed near the analog and digital interface circuitry to shorten signal paths, while sensitive analog sections remain physically separated from USB and switching nodes. Firmware development must include scaling, calibration, fault handling, and boundary checks because MCU processing speed does not replace accurate front-end design.
Recomendado
Battery-Powered Measurement Device
The MKL26Z64VFT4 suits battery-powered measurement equipment where a 32-bit Cortex-M0+ processor, 64 KB of flash, and USB connectivity can replace several separate discrete functions. Firmware can use low-power operating modes between measurements, then activate the USB device controller when data transfer is requested. This architecture is especially useful for portable analyzers and service tools that need a compact digital section and periodic computer connectivity. Power-budget calculations should separate sensor, analog, regulator, and USB-load currents. The NXP operating-mode current values should be used with realistic duty cycles rather than assuming that the 48 MHz processing rate is continuously active.
Recomendado
Programmable Automation Controller
The MKL26Z64VFT4 can serve as the programmable center of a compact automation or test fixture, handling logic sequences, I/O decisions, timing, and USB-based configuration. Its 48 MHz Cortex-M0+ core supports responsive event handling, while 64 KB of flash accommodates control code, limits, and calibration data. Because the MCU consolidates multiple functions, the design should use clear isolation between external power domains and low-voltage logic. Firmware must include safe-state initialization, watchdog recovery, and output interlocks. USB should be treated as a service or configuration channel rather than the only control path when unattended operation and deterministic behavior are required.
Recomendado
USB Field-Service Adapter
The MKL26Z64VFT4 is well suited to a field-service adapter that connects an instrument or machine to a computer for configuration, logging, or diagnostics. The full-speed USB device controller handles the physical host interface, and the Cortex-M0+ core can interpret commands, run application firmware, and manage status indicators. With 64 KB of flash, the adapter can hold protocol handlers and product-specific logic without an external memory device. Design the USB connector and protection network carefully, provide a reliable device identity, and include timeout behavior for incomplete host commands. A bootloader strategy and recoverable firmware image improve serviceability without changing the pin-compatible MCU architecture.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para MKL26Z64VFT4 — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | MKL26Z64VCM4 | MKL26Z64VFM4 | MKL26Z64VCM4R | MKL26Z64VFM4R | MKL26Z64VFT4R |
|---|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 48-QFN (7x7 mm) | 48-QFN (7x7 mm) | 48-QFN (7x7 mm) | 48-QFN (7x7 mm) | 48-QFN (7x7 mm) | 48-QFN (7x7 mm) |
| Processor Core | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ |
| Flash Memory | 64 KB | 64 KB | 64 KB | 64 KB | 64 KB | 64 KB |
| Ordering Configuration | VFT4 tape-and-reel suffix | VCM4 suffix | VFM4 suffix | VCM4R reel suffix | VFM4R reel suffix | VFT4R reel suffix |
Diferenciadores clave
- Combines a 48 MHz Cortex-M0+ core with native USB device connectivity (frente a MKL26Z64VCM4)
- Matches the exact 64 KB memory configuration of the family alternatives (frente a MKL26Z64VFM4)
- Offers a direct reel-style procurement configuration without changing the device family (frente a MKL26Z64VCM4)
- Maintains the same pin-compatible 48-QFN footprint across listed alternatives (frente a MKL26Z64VFM4R)
Notas de diseño
Use the 48-QFN land pattern and exposed-pad layout from the NXP package drawing without modifying pad dimensions or thermal-via geometry. Place the device close to its decoupling capacitors and keep the USB differential pair short, continuous, and free of test pads or other high-impedance branches. Confirm the exact pin names from the datasheet before assigning nets because an exposed pad and the 48 perimeter pins serve different electrical roles.
Budget the power rail around the sum of active-core, USB, and attached peripheral loads rather than the 48 MHz clock rate alone. Use the manufacturer operating-mode current figures to estimate average consumption, then include regulator efficiency, USB attachment, and startup margin. If the design uses a battery, evaluate USB-connected and disconnected states separately because peripheral activity and bus-state transitions can materially change the duty-cycle estimate.
Do not infer that every MKL26Z64 member has identical suffix-specific temperature, USB, or ordering behavior. Before releasing a replacement, compare the complete ordering information, electrical limits, pin table, USB configuration, flash organization, and exposed-pad requirements against the MKL26Z64VFT4. Also verify the reel orientation and quantity for an R suffix, since changing the ordering suffix without checking assembly requirements can create a production mismatch.
Keep sensitive analog inputs and external precision components away from the MCU, USB routing, and switching-power circuitry. Provide a quiet ground-return path and place local bypass capacitance at the supply pins. When the USB interface is used, follow the manufacturer’s differential-routing, impedance, connector, and ESD guidance exactly; software configuration cannot compensate for a physical USB signal-integrity problem.
Información de cumplimiento
No explicit compliance declarations were identified in the manufacturer product-page excerpt or distributor catalog snippets. Check the NXP product page and current material declaration for the exact ordering configuration.