MPXR4040VVU264 - 264MHz 32-bit MCU with 4MB Flash | NXP
N.º de pieza: MPXR4040VVU264 ✗ Fin de vida| Cant. | Precio unitario | Total |
|---|---|---|
| 1 | $1.0048 | $1,00 |
| 10 | $0 | $0,00 |
| 100 | $0 | $0,00 |
| 500 | $0 | $0,00 |
| 1.000 | $0 | $0,00 |
MPXR4040VVU264 Descripción general
A microcontroller is a programmable system-on-chip that combines a processor core, memory, communication peripherals, timers, and I/O in one device. The MPXR4040VVU264 belongs to the PX Series and uses a 32-bit e200z7 core built around Power Architecture technology. This places it in the embedded-controller hierarchy: MCU -> real-time processor -> embedded semiconductor. Its combination of local flash, serial interfaces, and real-time peripherals supports industrial networking, machine control, automotive-style communications, and test equipment without requiring a separate external processor.
The verified data confirms a 264 MHz operating speed, 4 MB (4M x 8) flash, 32-bit processing, 198 I/O, and a 416-terminal square BGA package. The available connectivity includes CANbus, EBI/EMI, LINbus, SCI, SPI, UART/USART, DMA, POR, PWM, and WDT. These interfaces allow the device to coordinate networked nodes, external memories, actuator controls, and real-time data paths. The 198 available I/O provide substantial board-level integration for sensors, communication transceivers, power-control signals, and industrial logic.
The e200z7 architecture and 264 MHz class position the part in performance-oriented real-time embedded designs rather than low-cost basic control. Flash memory supports local firmware storage, while DMA can reduce processor involvement in data transfers. PWM and watchdog resources support periodic actuator drive and system monitoring, and the communication peripherals cover common industrial and embedded control buses. The supplied data does not specify RAM capacity beyond a conflicting distributor snippet, operating voltage, memory-map details, or electrical timing limits.
Typical applications include industrial automation controllers, CAN and LIN network nodes, motor and power-control systems, communications equipment, and embedded test or measurement platforms. Designers should prioritize the 416-ball PBGA layout and verify the exact pin-level requirements, power rails, clock configuration, and board-level escape routing before layout begins. Because the package uses 416 balls rather than a leaded package, a multilayer PCB and appropriate assembly process are normally required.
The MPXR4040VVU264 is listed as obsolete by one datasheet source, so procurement should confirm lifecycle and counterfeit risk before committing to new production. LCSC shows a price from $1.0048 in the verified search result, while Heisener reports inventory but requests a quotation. These figures are commercial snapshots, not guaranteed XAIPART inventory or a universal replacement price.
This page consolidates verified distributor specifications, interface details, lifecycle signals, sourcing context, and engineering caveats. It is intended to help engineers distinguish the obsolete controller from possible alternatives, assess compatibility, and plan a controlled redesign rather than assuming that any cross-reference is automatically pin-to-pin equivalent.
Alternativas directas para MPXR4040VVU264 — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con MPXR4040VVU264 (mismo factor de forma y huella) — difiere en Core Architecture, Mounting Type, Package, Product Type, Program Memory.
Herramienta de comparación rápida — seleccione piezas alternativas para compararlas lado a lado:
MPXR4030VVU264
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
MPXR4040VVU264
✅ Sustitución directa✓ En stock
Consulte el precio
Ver hoja de datos →MPC5121VY400
✅ Sustitución directa✓ En stock
Consulte el precio
Ver hoja de datos →MCF5327CVM240J
✅ Sustitución directa✓ En stock
$15.95 / unidad
Ver hoja de datos →SPC5674FF3MVV3
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
MPXR4040VVU264 Valores máximos y características eléctricas
| Product Type | 32-bit microcontroller |
| Series | PX Series |
| Core Processor | e200z7 |
| Core Architecture | Power Architecture |
| Processor Bit Width | 32-bit |
| Maximum Clock Speed | 264 MHz |
| Program Memory | 4 MB (4M x 8) |
| Program Memory Type | Flash |
| I/O Count | 198 |
| Connectivity | CANbus, EBI/EMI, LINbus, SCI, SPI, UART/USART |
| Peripherals | DMA, POR, PWM, WDT |
| Encapsulado | 416-PBGA, 27 x 27 mm |
| Terminal Count | 416 balls |
| Temperature Grade | Industrial |
| Estado del ciclo de vida | Obsolete |
Guía de configuración de pines de MPXR4040VVU264 416-pbga, 27 x 27 mm
Configuración de pines para MPXR4040VVU264 (encapsulado 416-pbga, 27 x 27 mm). Este CI digital incluye GPIO, interfaces de comunicación (UART, SPI, I2C) y pines de alimentación. Consulte la hoja de datos del fabricante para conocer las funciones alternativas de los pines y las opciones de configuración. Esencial para el diseño de sistemas embebidos y el diseño de PCB.
No hay datos detallados de patillaje disponibles para MPXR4040VVU264.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
MPXR4040VVU264 es adecuado para 6 aplicacións: Industrial Automation Controller, CAN and LIN Networked Equipment, Motor and Power-Control Systems, Communications and Protocol Gateways, Embedded Test and Measurement Equipment, Real-Time Data Acquisition Node.
Industrial Automation Controller
The MPXR4040VVU264 fits high-complexity industrial automation control because its verified 264 MHz e200z7 processor provides real-time computing performance and its 198 I/O support numerous field-level signals. CANbus, LINbus, SCI, SPI, and UART/USART connectivity can connect sensors, remote I/O, operator interfaces, and network nodes. PWM and watchdog resources are useful for actuator timing and system supervision. The 416-PBGA package supports dense board integration, but multilayer routing, BGA assembly, power integrity, and exact pin verification are essential. Because the device is reported obsolete, it is most appropriate for maintaining an existing platform when no redesign is practical, rather than for a new long-life product.
Recomendado
CAN and LIN Networked Equipment
For industrial networking, the MPXR4040VVU264 combines a 264 MHz 32-bit core with verified CANbus and LINbus connectivity, while SCI, SPI, UART/USART, and EBI/EMI provide additional paths to transceivers and external devices. This combination is useful in network controllers, gateway equipment, and distributed machine nodes. The 4 MB flash supports local firmware and protocol configuration storage, and DMA can help move communication data efficiently. The designer must still verify transceiver logic levels, termination, bus timing, pin multiplexing, and the exact 416-ball package layout. Obsolete lifecycle status increases maintenance and counterfeit-control risk for long-lived network infrastructure.
Recomendado
Motor and Power-Control Systems
The MPXR4040VVU264 is a candidate for real-time motor and power-control systems because the verified 264 MHz processing rate supports deterministic control loops and the PWM peripheral can drive timing-sensitive power stages. Its CANbus and LINbus links allow supervisory communication with power modules, inverters, or remote actuators, while DMA supports efficient transfer of control and diagnostic data. The 198 I/O provide ample signals for position, enable, fault, interlock, and sensing functions. A production design must check voltage levels, timer channel assignment, analog support, isolation, thermal conditions, and safety requirements, none of which are fully specified in the supplied data.
Recomendado
Communications and Protocol Gateways
The MPXR4040VVU264 can serve as the central controller in communications equipment because it offers multiple verified serial interfaces: CANbus, LINbus, SCI, SPI, UART/USART, and EBI/EMI. A gateway design can use one MCU to collect data from a field bus, format it, and forward it over a host interface, while 4 MB flash accommodates firmware and protocol tables. The 264 MHz core and DMA support concurrent communication tasks, but interrupt latency, bus timing, buffer sizing, and pin multiplexing must be validated against the detailed datasheet. The obsolete status means gateway designs should include lifecycle monitoring and a planned migration path to a supported MCU.
Recomendado
Embedded Test and Measurement Equipment
The MPXR4040VVU264’s 32-bit e200z7 core, 264 MHz clock, 4 MB flash, DMA, and broad serial connectivity make it relevant to embedded instrumentation and automated test equipment. It can coordinate acquisition peripherals, external memory, communication transceivers, and timing or PWM-driven stimulus. The 416-PBGA package allows a high pin count in a compact 27 x 27 mm footprint, although it requires advanced assembly and multilayer PCB capabilities. For laboratory or production test systems, engineers should verify electrical limits, clock accuracy, ADC resources, memory interfaces, and watchdog behavior from the manufacturer documentation; those details are not present in the supplied snippets.
Recomendado
Real-Time Data Acquisition Node
For real-time acquisition, the MPXR4040VVU264 offers a 264 MHz 32-bit processor, DMA, PWM, watchdog, and multiple communication interfaces in one device. A sensor or machine-monitoring node can collect data through a suitable external interface, process it locally, and transmit results through CANbus, LINbus, SCI, or UART/USART. The 198 I/O and 4 MB flash support distributed firmware and signal management, while the industrial-grade marking is relevant to controlled environments. The design must account for sensor signal conditioning, electrical protection, grounding, timing accuracy, and package-level escape routing. Obsolete availability makes traceability and long-term spare planning especially important.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para MPXR4040VVU264 — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | MPXR4030VVU264 | MPC5121VY400 | MCF5327CVM240J | SPC5674FF3MVV3 |
|---|---|---|---|---|---|
| Package | 416-PBGA (27 x 27 mm) | 416-PBGA (27 x 27 mm) - comparison candidate; exact package verification required | 416-PBGA (27 x 27 mm) - site-listed candidate; exact package verification required | 416-PBGA (27 x 27 mm) - site-listed candidate; exact package verification required | 416-PBGA (27 x 27 mm) - comparison candidate; exact package verification required |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
Diferenciadores clave
- Verified high-frequency e200z7 performance (frente a MPXR4030VVU264)
- Verified 4 MB flash configuration (frente a MPC5121VY400)
- Verified industrial interface set (frente a SPC5674FF3MVV3)
- Verified 198-I/O integration (frente a MCF5327CVM240J)
Notas de diseño
The verified 416-PBGA package requires a multilayer PCB strategy with controlled escape routing for power, ground, high-speed interfaces, and all 416 balls. Do not infer ball assignments from a distributor snippet; obtain the official package drawing and pin table before routing. Use the manufacturer’s recommended layer stack, via-in-pad or via fanout approach, solder-mask definition, and assembly land pattern. Estimated: the 27 x 27 mm package leaves little routing margin for escape, so power and ground distribution should be resolved before signal breakout.
Do not treat a generic cross-reference match as a drop-in replacement. The supplied alternatives data identifies comparison candidates but does not verify identical ball maps, voltage levels, clock limits, memory maps, peripheral assignments, or software startup behavior. Before substituting any MPN, compare the official datasheets, pin table, memory organization, reset/boot requirements, interrupt vector layout, and peripheral register compatibility. Estimated: a software mismatch can prevent operation even when the package dimensions appear identical.
Thermal design must be based on the actual supply voltage, core activity, clock utilization, I/O loading, and PCB construction, because those values are not supplied in the verified snippets. A 264 MHz MCU in a 416-ball BGA may require multilayer thermal-via arrays and carefully controlled copper planes. Estimated: without the complete electrical and thermal data, no junction-temperature or power-dissipation value can be responsibly calculated. Use the manufacturer thermal characterization data and measure the assembled board under worst-case ambient and load conditions.
Plan power sequencing, decoupling, and ground return paths from the official hardware design guidance before schematic release. The verified data confirms flash, DMA, PWM, watchdog, and serial peripherals but does not provide supply rails or pin-level power requirements. Decoupling capacitor placement, voltage tolerances, startup ramp limits, and analog-versus-digital isolation must therefore be confirmed from the datasheet. Estimated: the 264 MHz operating rate and extensive I/O make power integrity and return-current discipline as important as schematic connectivity.
Keep communication routes such as CANbus, LINbus, SPI, UART/USART, SCI, and EBI/EMI away from switching nodes and noisy power-return paths. Match trace geometry and reference planes according to the actual signal-rate requirements, which are not provided in the verified data. Provide clean return paths through the BGA escape structure and test interface rise time, ringing, crosstalk, and bus timing on representative hardware. Estimated: the large ball count can create significant routing congestion, making early constraint-driven placement essential.
Información de cumplimiento
The supplied verified data does not include RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations. Industrial temperature-grade marking is not equivalent to AEC-Q100 qualification.
