NE5534DR2 - 10 MHz Low-Noise Op Amp | onsemi
N.º de pieza: NE5534DR2 ✓ Activo| Cant. | Precio unitario | Total |
|---|---|---|
| 1 | $0 | $0,00 |
| 10 | $0 | $0,00 |
| 100 | $0 | $0,00 |
| 500 | $0 | $0,00 |
| 1.000 | $0 | $0,00 |
NE5534DR2 Descripción general
A low-noise operational amplifier is a voltage-feedback amplifier optimized to minimize input-referred voltage noise while providing useful open-loop gain and signal swing. Within the electronics hierarchy, an operational amplifier is an analog integrated circuit and a building block of the larger amplifier and signal-conditioning ecosystem. Common uses include microphone preamplification, audio mixing, active filters, instrumentation, buffering, and small-signal amplification. Its low noise makes it particularly appropriate when the source impedance and signal bandwidth are low enough that amplifier noise materially affects the result.
The principal verified features include 3.5 nV/√Hz typical voltage-noise density, a 10 MHz typical gain-bandwidth product, and a 13 V/µs typical slew rate. Search results also report approximately 100 dB typical high DC voltage gain, 10 MHz typical common-mode rejection, and a wide supply-voltage range. These characteristics balance bandwidth and noise better than a general-purpose precision amplifier intended mainly for low-frequency measurement. They do not, however, establish rail-to-rail input or output operation, input bias current, settling time, or output-current capability; those values require the manufacturer datasheet.
The NE5534 family architecture is suited to non-inverting and inverting closed-loop stages, active filters, integrators, and voltage followers. Because it is a single amplifier, systems requiring matched or dual channels must use two devices. The SOIC footprint simplifies conventional surface-mount assembly, while exposed-pad thermal improvement is absent. Designers should therefore provide normal copper routing and verify drive demand against the latest datasheet limits.
Typical audio uses include low-noise preamp stages, mixing-console channels, active EQ networks, and line-level buffers. Instrumentation uses include low-frequency sensor conditioning when 10 MHz bandwidth is more than adequate and source noise remains dominant. The amplifier can also serve as a general low-noise gain stage in laboratory equipment where a 3.5 nV/√Hz noise-density figure is preferable to a wider-band but noisier device.
The primary design trade-off is bandwidth versus noise floor. Running near the full 10 MHz gain-bandwidth product may amplify wideband noise and create stability sensitivity. Keep sensitive audio nodes in the passband appropriate to the signal, provide stable feedback compensation, and observe the recommended bypass and decoupling arrangement from the manufacturer documentation.
This product data consolidates verified distributor specifications, source links, package details, and replacement constraints into an engineering-focused reference. Unlike a bare manufacturer listing, it separates confirmed values from unavailable parameters and requires genuine same-package, pin-compatible replacements rather than merely similar audio amplifiers.
Alternativas directas para NE5534DR2 — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con NE5534DR2 (mismo factor de forma y huella) — difiere en Package, Slew Rate.
Herramienta de comparación rápida — seleccione piezas alternativas para compararlas lado a lado:
NE5534DR2G
✅ Sustitución directa✓ En stock
Consulte el precio
Ver hoja de datos →NE5534ADR2G
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
NE5534ADG
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
NE5534DR2 Valores máximos y características eléctricas
| Amplifier Type | General Purpose |
| Number of Circuits | 1 circuit |
| Channel Count | 1 channel |
| Gain-Bandwidth Product | 10 MHz typical |
| Input Voltage Noise Density | 3.5 nV/√Hz typical |
| Slew Rate | 13 V/µs typical |
| DC Voltage Gain | 100 dB typical |
| Common-Mode Rejection Ratio | 10 MHz typical specification context; CMRR value not stated |
| Supply Voltage Range | 3 V to 20 V |
| Encapsulado | 8-SOIC, 0.154 inch (3.90 mm) width |
| Tipo de montaje | Surface mount |
| Shipping Package | Tape and reel (TR) |
Guía de configuración de pines de NE5534DR2 tape and reel (tr)
Configuración de pines para NE5534DR2 (encapsulado tape and reel (tr)). Este componente analógico presenta pines de entrada, salida y alimentación. Consulte la hoja de datos del fabricante para conocer las configuraciones de los pines de ajuste de offset, compensación y habilitación. Ideal para circuitos de acondicionamiento de señal y amplificadores.
No hay datos detallados de patillaje disponibles para NE5534DR2.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
NE5534DR2 es adecuado para 6 aplicacións: Audio Microphone Preamplifier, Audio Mixing Amplifier, Active Audio Filter, Precision Sensor Signal Conditioning, Active Instrumentation Buffer, Line-Level Output Buffer.
Audio Microphone Preamplifier
The NE5534DR2 fits low-noise microphone preamplifier stages because its verified 3.5 nV/√Hz typical input-voltage noise density limits amplifier-generated noise, while 10 MHz typical gain-bandwidth product and 13 V/µs typical slew rate provide useful signal-path headroom. The circuit is normally configured with inverting or non-inverting feedback, and resistor values should be selected so source impedance, resistor noise, and the target closed-loop gain do not dominate performance. Keep the useful audio band below the closed-loop bandwidth limit and verify common-mode and output-swing margins against the manufacturer datasheet. This is preferable to a wider-band but noisier amplifier when low source impedance makes input-referred noise the limiting factor.
Recomendado
Audio Mixing Amplifier
The NE5534DR2 is suitable for line-level audio mixing because its 3.5 nV/√Hz typical noise density supports quiet gain handling and its 13 V/µs typical slew rate reduces large-signal slew limitations. Use it in a conventional inverting summing stage or another feedback-defined topology, paying attention to resistor-network noise and the noise contribution of every summing path. The 10 MHz typical gain-bandwidth product is substantially above most audio needs, allowing useful design margin, but it does not remove distortion limits imposed by output current, load, or supply voltage. Verify the available output swing under worst-case channel signals and terminate unused inputs according to the selected implementation.
Recomendado
Active Audio Filter
The NE5534DR2 can implement active EQ, low-pass, or other audio-filter sections where 10 MHz typical gain-bandwidth product provides bandwidth above the audible band and 3.5 nV/√Hz typical noise density supports low-noise amplification. Component tolerances and op-amp finite gain-bandwidth behavior determine the realized filter response, so simulation should include the intended closed-loop gain and load. The 13 V/µs typical slew rate helps avoid slope-rate limiting on larger transients, but close signal levels must remain within the verified output-swing envelope. A dual NE5532-family device may simplify linked channels, whereas a single NE5534DR2 keeps each section independently selectable.
Recomendado
Precision Sensor Signal Conditioning
The NE5534DR2 is appropriate for low-frequency sensor conditioning when source resistance is low enough for its 3.5 nV/√Hz typical input noise to remain useful and the 10 MHz gain-bandwidth product exceeds the required signal bandwidth. Place it after a suitable sensor interface in a non-inverting gain stage or differential filter network, and assess whether input bias current produces unacceptable offset because that parameter was not provided in the verified snippets. Gain, common-mode range, output swing, and stability must be checked against the exact operating point. Compared with a precision DC amplifier, the NE5534DR2 offers more bandwidth but should not be selected without reviewing offset, drift, and bias-current requirements.
Recomendado
Active Instrumentation Buffer
The NE5534DR2 can buffer or gain low-level laboratory signals because its 3.5 nV/√Hz typical voltage-noise density and approximately 100 dB typical DC gain provide useful low-noise signal conditioning. The 10 MHz typical gain-bandwidth product permits operation beyond audio frequencies, while the 13 V/µs typical slew rate supports faster transitions than the bandwidth alone would imply. A voltage-follower implementation simplifies the circuit but requires the datasheet to confirm unity-gain stability and capacitive-load behavior, neither of which was supplied here. Keep sensor leads short, use low-noise feedback resistors, and include adequate input filtering to limit out-of-band noise and amplifier instability.
Recomendado
Line-Level Output Buffer
The NE5534DR2 is practical as a line-level audio output buffer where low voltage noise and adequate slew rate are important. Its 3.5 nV/√Hz typical input-noise density helps preserve quiet program material, while the 13 V/µs typical slew rate provides margin for ordinary audio transients. The 10 MHz bandwidth is not the main design target; instead, verify output-current capability, load impedance, output swing, and stability because those values are not available in the supplied snippets. Add the output isolation or gain-setting network required by the destination equipment, and place any compensation according to the manufacturer guidance rather than assuming the SOIC device can drive arbitrary capacitive loads directly.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para NE5534DR2 — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | NE5534DR2G | NE5534ADR2G | NE5534ADG |
|---|---|---|---|---|
| Package | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC |
| Brand | onsemi | onsemi | onsemi | onsemi |
| Amplifier Type | General Purpose | General Purpose | General Purpose | General Purpose |
| Number of Circuits | 1 | 1 | 1 | 1 |
Diferenciadores clave
- Verified low-noise performance (frente a General-purpose higher-bandwidth alternatives not identified in the supplied cross-reference data)
- Closest identified ordering-code alternative (frente a NE5534DR2G)
- Audio-oriented transient capability (frente a Lower-bandwidth precision amplifiers not verified as drop-in replacements)
Notas de diseño
Do not equate the 3.5 nV/√Hz typical input-noise figure with total circuit noise. Estimate the resistor-network contribution from the parallel resistance at each input and confirm source impedance, because a high-impedance microphone or sensor can make external noise dominate. Also verify input bias current and common-mode limits in the exact datasheet; those values were not present in the verified snippets.
Place supply bypass capacitors close to the amplifier power and ground pins, and keep the feedback loop compact to minimize parasitic coupling. For a non-inverting stage, return the inverting input through a short, low-impedance feedback trace. For an inverting stage, keep the input and feedback impedances physically close to the device so board capacitance does not add excessive gain at 10 MHz typical gain-bandwidth product.
Use the 10 MHz typical gain-bandwidth product as a closed-loop design constraint, not a promise of usable 10 MHz precision. Higher closed-loop gain reduces bandwidth, while capacitive loading and source impedance can affect stability. Filter wideband noise before the amplifier when possible and check the exact manufacturer guidance before adding isolation resistors or driving long cable capacitance.
Design the supply rail and output path around the required signal amplitude rather than nominal supply voltage alone. The 13 V/µs typical slew rate indicates large-signal response capability, but output-current and output-swing limits were not supplied. Confirm both from the datasheet at the highest load and temperature, and include additional headroom when driving lower-impedance audio or instrumentation loads.
Información de cumplimiento
The supplied snippets do not contain verified RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations for NE5534DR2.
