OPA2822U - Dual 500 MHz Low-Noise Op Amp | Texas Instruments
N.º de pieza: OPA2822U ✓ ActivoOPA2822U Descripción general
An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its two inputs. Its high-level hierarchy is operational amplifier, analog amplifier, amplifier IC, and semiconductor. A wideband operational amplifier combines high unity-gain bandwidth with low input noise, making it useful in communications, instrumentation, audio, filtering, and signal-conditioning systems where both signal speed and noise performance matter.
Key features include exceptionally low input noise of 2.0 nV/√Hz, high unity-gain bandwidth of 500 MHz, and a gain-bandwidth product of 240 MHz. Each channel draws 4.8 mA of supply current, while the output stage can provide 90 mA of output current. These characteristics allow the OPA2822U to process small signals with high gain while preserving bandwidth and driving passive filter networks.
The OPA2822U uses a wideband, unity-gain-stable voltage-feedback architecture. Its low-noise behavior is especially valuable in differential receiver circuits, where the amplifier must recover small signals without adding substantial broadband noise. The combination of 500 MHz bandwidth, 90 mA output-current capability, and single-supply operation supports broadband analog filtering, impedance conversion, and line-driver functions.
Typical applications include xDSL receiver front ends, differential signal conditioning, low-noise active filters, video and audio signal paths, communications equipment, and test-and-measurement instrumentation. In an xDSL input stage, the amplifier can provide differential gain while its low input noise helps preserve the signal-to-noise ratio of the received data stream.
For stable operation, follow the manufacturer datasheet when selecting feedback components, output loading, supply bypassing, and source or sink impedance. Place decoupling capacitors close to the supply pins, keep feedback traces short, and use symmetric routing where high differential bandwidth and common-mode rejection are required. The 8-pin SOIC footprint makes the device suitable for conventional surface-mount assembly.
This page combines manufacturer specifications, verified distributor availability information, a strict drop-in cross-reference assessment, comparison parameters, and practical PCB and signal-integrity guidance to support component selection, replacement review, and design implementation.
Alternativas directas para OPA2822U — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
OPA2822UG4
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
OPA2822U Valores máximos y características eléctricas
| Amplifier Type | Dual voltage-feedback operational amplifier |
| Number of Channels | 2 channels |
| Input Noise Voltage | 2.0 nV/√Hz |
| Unity-Gain Bandwidth | 500 MHz |
| Gain-Bandwidth Product | 240 MHz |
| High Output Current | 90 mA |
| Corriente de alimentación | 4.8 mA per channel |
| Single-Supply Operation | Single to +12 V |
| Gain Stability | Unity-gain stable |
| Rango de temperatura de funcionamiento | -40°C to +85°C |
| Encapsulado | 8-pin SOIC (D) |
| Tipo de montaje | Surface mount |
| Differential Signal Support | Optimized for differential configurations |
| Harmonic Distortion | Exceptionally low in differential configurations |
| Estado RoHS | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | unknown |
| Lead-Free Status | unknown |
Configuración de pines de OPA2822U
| Pin 1 | OUTA — Output of amplifier A |
| Pin 2 | IN A- — Inverting input of amplifier A |
| Pin 3 | IN A+ — Noninverting input of amplifier A |
| Pin 4 | V- — Negative supply connection |
| Pin 5 | IN B+ — Noninverting input of amplifier B |
| Pin 6 | IN B- — Inverting input of amplifier B |
| Pin 7 | OUTB — Output of amplifier B |
| Pin 8 | V+ — Positive supply connection |
Aplicaciones típicas
OPA2822U es adecuado para 6 aplicacións: xDSL Receiver Front End, Wideband Active Filtering, Differential Signal Conditioning, Low-Noise Instrumentation, Audio and Video Signal Paths, Test and Measurement Equipment.
xDSL Receiver Front End
The OPA2822U fits xDSL receiver front ends because its 2.0 nV/√Hz input noise limits amplifier-added broadband noise while its 500 MHz unity-gain bandwidth preserves wideband signal content. The Texas Instruments OPA2822 datasheet specifically identifies xDSL receiver applications and emphasizes low harmonic distortion in differential configurations. Each channel can be arranged as part of a differential gain stage, and the 90 mA output-current capability can support suitable passive-filter networks. Keep the feedback loop compact and place supply-bypass capacitors near pins 4 and 8 to preserve stability across the wide operating bandwidth.
Recomendado
Wideband Active Filtering
The OPA2822U is suitable for wideband active filters because its 500 MHz unity-gain bandwidth supports signal amplification above the frequencies commonly handled by general-purpose precision op amps. Its 240 MHz gain-bandwidth product allows useful closed-loop bandwidth at higher closed-loop gains, while 2.0 nV/√Hz input noise limits degradation of small signals. The voltage-feedback architecture also provides a direct basis for choosing stable feedback values according to the manufacturer datasheet. For passive-filter loading, the output stage's 90 mA capability provides additional drive headroom.
Recomendado
Differential Signal Conditioning
OPA2822U differential signal conditioning benefits from the device's 2.0 nV/√Hz input noise, 500 MHz unity-gain bandwidth, and low harmonic distortion in differential configurations. A dual implementation can amplify the positive and negative halves of a balanced signal while preserving matching if the two channels use symmetrical layouts and resistor networks. The 240 MHz gain-bandwidth product gives designers useful bandwidth margin at closed-loop gains above unity. Route the two channels as symmetrically as practical to avoid introducing gain imbalance or additional conversion from common-mode noise into differential output error.
Recomendado
Low-Noise Instrumentation
The OPA2822U can serve low-noise instrumentation front ends when a design needs both 2.0 nV/√Hz input-noise performance and high signal bandwidth. Its dual-channel architecture supports separate sensing or buffering paths without requiring two discrete packages, while the 500 MHz unity-gain bandwidth handles fast sensor signals and test fixtures. Input offset, bias current, common-mode range, and stability must still be checked against the application's transducer and source impedance. Use short input paths, clean grounding, and symmetrical feedback structures to prevent board-level coupling from overwhelming the amplifier's low intrinsic noise.
Recomendado
Audio and Video Signal Paths
OPA2822U is applicable to high-bandwidth audio and video signal paths when the circuit requires low input noise and high unity-gain bandwidth. The 2.0 nV/√Hz noise specification helps preserve quiet signal handling, while 500 MHz bandwidth provides ample headroom for wideband gain and filtering stages. Its 90 mA output-current capability allows it to drive suitable passive networks rather than relying on an external buffer in every design. Verify output swing, load impedance, and distortion against the datasheet because wideband behavior and output-current limits are both frequency- and amplitude-dependent.
Recomendado
Test and Measurement Equipment
The OPA2822U suits test and measurement equipment requiring accurate amplification of small, fast signals. Its 2.0 nV/√Hz input noise minimizes the amplifier contribution to the measurement floor, while 500 MHz unity-gain bandwidth supports high-frequency source monitoring and active probes. The dual amplifier can be used for complementary channels, buffer functions, or differential input stages. Designers should still evaluate output swing, load behavior, input bias current, and channel matching for the exact test range. Stable feedback values and short, symmetric PCB traces are especially important when operating close to the amplifier's high-bandwidth limit.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para OPA2822U — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | OPA2822UG4 |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | 8-pin SOIC (D) | 8-pin SOIC - same |
| Amplifier Configuration | Dual | Dual |
| Architecture | Voltage feedback | OPA2822 family voltage-feedback architecture |
| Input Noise Voltage | 2.0 nV/√Hz | 2.0 nV/√Hz |
| Unity-Gain Bandwidth | 500 MHz | 500 MHz |
| Gain-Bandwidth Product | 240 MHz | 240 MHz |
| Supply Current | 4.8 mA per channel | 4.8 mA per channel |
| Maximum Output Current | 90 mA | 90 mA |
| Operating Temperature Range | -40°C to +85°C | -40°C to +85°C |
| Single-Supply Operation | Single to +12 V | Single to +12 V |
| RoHS Status | unknown | unknown |
Diferenciadores clave
- Combines very low input noise with high unity-gain bandwidth (frente a OPA2822UG4)
- Supports dual differential signal conditioning in one package (frente a OPA2822UG4)
- Provides output drive for passive filter networks (frente a OPA2822UG4)
Notas de diseño
Place the manufacturer-recommended bypass capacitors immediately adjacent to pins 4 and 8, with short ground returns. Keep each feedback resistor and capacitor close to its amplifier pins rather than routing feedback around the package. The OPA2822U reaches 500 MHz unity-gain bandwidth, so even a small parasitic loop can create ringing or reduced phase margin. Use a continuous ground plane, minimize supply inductance, and avoid placing high-speed digital or switching-current paths beneath the feedback and input nodes.
Route the two amplifier channels symmetrically when the circuit depends on differential cancellation. Matching the input and feedback geometry helps reduce differential-to-common-mode conversion and channel skew at high frequency. The 2.0 nV/√Hz input noise is valuable only if board-level coupling and ground noise do not dominate; use a quiet ground reference and terminate unused inputs according to the manufacturer recommendations. For cable-connected inputs, control source impedance and connector return paths before relying on the amplifier's intrinsic noise performance.
Do not assume that a 500 MHz unity-gain bandwidth guarantees useful bandwidth at every closed-loop gain. The OPA2822U has a 240 MHz gain-bandwidth product, so higher closed-loop gains reduce available bandwidth. Select feedback values from the manufacturer stability and frequency-response guidance, and check output swing under the intended load. The 90 mA output-current rating is not a continuous-load guarantee across all output voltages and frequencies; verify the relevant combination in the datasheet.
Información de cumplimiento
The manufacturer product and datasheet pages were identified, but no explicit compliance declaration was included in the verified product details.