NXP Semiconductors

PCA6408AHKX - 8-Bit I2C I/O Expander | NXP Semiconductors

N.º de pieza: PCA6408AHKX ✓ Activo
5.5 V Vdss 16-pin XQFN Package 400 kHz Speed
MOQ: 1 |

PCA6408AHKX Descripción general

The NXP Semiconductors PCA6408AHKX is an 8-bit I2C-bus and SMBus level-translating I/O expander with interrupt and reset functions, operating at up to 400 kHz and packaged in a 16-pin XQFN measuring 1.8 mm by 2.6 mm. It expands a host controller's available general-purpose input/output count while supporting both standard I2C and SMBus communication.

An I/O expander is an interface IC that translates serial bus commands into parallel digital input and output lines. In the system hierarchy, it sits between a microcontroller or embedded processor and external peripherals. The PCA6408AHK family provides eight configurable I/O ports, bidirectional interrupt signaling, and a reset input, making it useful when a controller has insufficient pins for switches, indicators, sensors, or relay-control signals.

The principal device features include eight I/O lines, I2C and SMBus support, operation at 100 kHz or 400 kHz, a stated maximum supply voltage of 5.5 V, and level-translating capability. The open-drain interrupt output becomes active when an input state differs from its corresponding input-port register state, allowing the connected controller to respond without continuously polling all eight pins. A dedicated reset input repeats the device's reset and initialization sequence without removing power.

The PCA6408AHKX combines a compact 16-pin XQFN package with a serial control interface intended for embedded control systems. Its level-translating architecture allows the I/O port voltage domain to be managed separately from the controller-side interface voltage when configured appropriately. This is particularly useful in systems where a low-voltage processor communicates with peripherals operating at a higher logic voltage, subject to the limits defined in the manufacturer datasheet.

Typical uses include industrial control panels, programmable logic controllers, building-automation equipment, battery-powered instrumentation, and compact consumer products. The eight ports can monitor discrete inputs or drive outputs such as status LEDs, relay-enable signals, and mode-selection controls. The interrupt output reduces unnecessary bus traffic when only a change on a monitored input requires controller attention.

PCB design should preserve the manufacturer's recommended pin, exposed-pad, decoupling, and layout constraints. Place input and output decoupling capacitors close to their associated supply pins, route the I2C bus with appropriate pull-up resistors, and confirm exposed-pad connection and thermal-via requirements during footprint review. The unusually small 1.8 mm by 2.6 mm body also makes assembly capability and solder-joint inspection important production considerations.

This product summary combines the confirmed interface, frequency, voltage, package, interrupt, and reset characteristics with practical guidance for PCB implementation, firmware control, and drop-in upgrade evaluation. It also identifies a directly related Agile I/O implementation for designs that require a pin-to-pin and software-compatible upgrade path.

Alternativas directas para PCA6408AHKX — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.

Variantes de esta serie

Modelos de la misma serie compatibles directamente con PCA6408AHKX (mismo factor de forma y huella) — difiere en Interrupt Output.

NXP Semiconductors
Interrupt Output: Yes (open-drain)
Comparar con PCA6408AHKX →

PCA6408AHK

✅ Sustitución directa
📦 16-pin XQFN
Same 8-bit PCA6408AHK interface and 400 kHz bus rating; the listed base-family ordering code does not itself identify the target's XQFN tape-and-reel suffix

📋 Alternativa de referencia (no en el catálogo)

PCAL6408AHK

✅ Sustitución directa
NXP Semiconductors
📦 16-pin XQFN
8-bit I2C-bus/SMBus level translating I/O expander · 8 · I2C, SMBus · 400 kHz · 1.65 V to 5.5 V · Yes (dual power rail) · Programmable output drive strength, latchable inputs · Yes (open-drain)

Consulte el precio

Ver hoja de datos →

PCA6408AHKX Especificaciones

Number of I/O Ports 8 ports
Serial Interface I2C-bus and SMBus
Maximum I2C Bus Frequency 400 kHz
Supported Bus Frequencies 100 kHz and 400 kHz
Maximum Supply Voltage 5.5 V
Tipo de interfaz Level-translating I/O expander
Interrupt Output Open-drain
Reset Function Dedicated RESET input
Package Type 16-pin XQFN
Package Dimensions 1.8 mm x 2.6 mm
Tipo de montaje Surface mount
Shipping Format Tape and reel

Guía de configuración de pines de PCA6408AHKX 1.8 mm x 2.6 mm

Configuración de pines para PCA6408AHKX (encapsulado 1.8 mm x 2.6 mm). La numeración de pines, las funciones y los diagramas de conexión se definen en la hoja de datos del fabricante. Consúltela para conocer el footprint exacto y las directrices de soldadura.

Diagrama de patillaje del encapsulado 1.8 mm x 2.6 mm para PCA6408AHKX

No hay datos detallados de patillaje disponibles para PCA6408AHKX.

Consulte la hoja de datos para ver la configuración completa de patillas.

Aplicaciones típicas

PCA6408AHKX es adecuado para 6 aplicacións: Compact Industrial Control Panels, Programmable Logic Controller Expansion, Building Automation Equipment, Battery-Powered Instrumentation, LED and Relay Control Interface, Consumer and IoT Peripheral Hub.

🏭

Compact Industrial Control Panels

The PCA6408AHKX suits compact control panels that need eight additional digital lines without enlarging the controller footprint. It connects to the host through I2C or SMBus at up to 400 kHz and can operate the ports as inputs, outputs, or mixed I/O according to the device configuration. The open-drain interrupt output reports an input-state change, reducing unnecessary polling when the controller is handling other real-time tasks. Its 16-pin XQFN body measures only 1.8 mm by 2.6 mm, helping preserve board area in densely populated industrial electronics.

⚡

Programmable Logic Controller Expansion

The PCA6408AHKX can add eight serial-controlled I/O lines to a programmable logic controller or embedded controller that has reached its direct GPIO limit. The bus supports 100 kHz and 400 kHz operation, while the level-translating architecture supports separate logic domains where permitted by the device limits. The interrupt output is useful when multiple inputs share a control card, allowing the controller to react to a changed state instead of repeatedly reading the bus. The compact XQFN package is particularly advantageous when expansion circuitry must fit beside existing relay or sensor interfaces.

🧩

Building Automation Equipment

The PCA6408AHKX is appropriate for building-automation controllers that interface with digital zone controls, occupancy indicators, alarms, or configurable equipment inputs. Eight ports provide a practical expansion granularity for retrofitting peripheral control functions around a central embedded processor. I2C operation up to 400 kHz permits efficient register-based control, and the interrupt output can promptly flag a changed sensor or switch state. Because the device supports level translation, it can help bridge compatible voltage domains, but the datasheet limits must be checked for each port and the power architecture.

📱

Battery-Powered Instrumentation

The PCA6408AHKX can extend the input and output capacity of a low-power instrument without adding eight direct microcontroller pins. Serial control reduces the number of host GPIO resources consumed, while the interrupt output lets the processor sleep between relevant input events instead of polling the expander continuously. The 16-pin XQFN package measures 1.8 mm by 2.6 mm, which supports compact handheld or portable equipment layouts. Firmware should configure unused ports appropriately, and actual standby current and operating-temperature behavior should be confirmed from the manufacturer electrical characteristics.

💡

LED and Relay Control Interface

The PCA6408AHKX provides a compact serial interface for eight discrete control lines used by status indicators, relay-enable circuits, mode selectors, or latching equipment. Register-based access through I2C or SMBus simplifies multiplexed control in boards with limited GPIO pins. At bus rates up to 400 kHz, the controller can update multiple output states efficiently, although external driver transistors are required for loads beyond the port's specified limits. The small XQFN footprint preserves routing space in densely populated control boards, and the interrupt function can also report changes on ports configured for input operation.

🧩

Consumer and IoT Peripheral Hub

The PCA6408AHKX can act as a compact peripheral hub in consumer appliances, smart-home controllers, and IoT modules. It gives an embedded controller access to eight additional digital lines for buttons, presence sensors, status indicators, or peripheral enables over I2C or SMBus. Operation at up to 400 kHz supports efficient register updates, while the open-drain interrupt output reduces communication overhead for event-driven inputs. The 1.8 mm by 2.6 mm XQFN package is useful where board area is constrained, although assembly yield and the exposed-pad layout require careful manufacturing review.

What is the PCA6408AHKX?
The PCA6408AHKX is an 8-bit level-translating I/O expander for I2C-bus and SMBus systems. It provides eight parallel I/O lines, open-drain interrupt signaling, and a reset input in a 16-pin XQFN package. NXP describes the device as an 8-bit I2C-bus/SMBus level-translating I/O expander with interrupt and reset, supporting 100 kHz and 400 kHz operation.
What is the maximum I2C bus frequency of the PCA6408AHKX?
The PCA6408AHKX supports operation at up to 400 kHz on the I2C-bus and SMBus interface. The manufacturer identifies 100 kHz and 400 kHz as supported bus rates. Bus timing, pull-up resistance, capacitance, and the controller's clock stretching behavior must all remain within the limits specified by the manufacturer datasheet for reliable 400 kHz operation.
What package and dimensions does the PCA6408AHKX use?
The PCA6408AHKX uses a 16-pin XQFN package measuring 1.8 mm by 2.6 mm. It is supplied in tape-and-reel format for surface-mount assembly. Because this body size is unusually compact, the PCB footprint, exposed-pad connection, solder mask, and assembly process should be reviewed against the manufacturer's land-pattern guidance before release to production.
How does the PCA6408AHKX interrupt output work?
The PCA6408AHKX uses an open-drain interrupt output to report a change in an input's state relative to its corresponding input-port register state. This allows a controller to avoid continuous polling when no monitored input has changed. The interrupt can be released or cleared through the device's serial interface, subject to the behavior defined in the manufacturer datasheet.
What does the RESET pin do on the PCA6408AHKX?
The RESET input causes the PCA6408AHKX to repeat its reset and initialization sequence without removing power from the device. This provides a hardware-controlled recovery path for a system controller that needs to return the port registers and internal state to a known condition. The exact active level, timing, and required pulse duration should follow the manufacturer datasheet.
Where can I download the PCA6408AHKX datasheet PDF?
The official datasheet and product resources are available from the NXP product page for the PCA6408AHK family at https://www.nxp.com/part/PCA6408AHK. The PCA6408AHKX ordering suffix identifies the tape-and-reel XQFN configuration. Use the pin-description table, electrical characteristics, register map, and recommended footprint from the manufacturer documentation when designing the circuit.
Where is the PCA6408AHKX pinout?
The PCA6408AHKX pinout is documented in the pin-description table of the NXP PCA6408AHK family datasheet. The device uses a 16-pin XQFN package, and the manufacturer documentation should be used to identify power pins, ground, I2C signals, port pins, RESET, and INT. The exposed thermal or electrical pad requirements must also be followed when creating the PCB footprint.
Where can I buy PCA6408AHKX online and check stock?
Use the Request a Quote form on this page to request PCA6408AHKX availability, current lead time, and order quantities for the exact XQFN tape-and-reel configuration. The 16-pin XQFN, tape-and-reel suffix, and required quantity should remain unchanged when requesting a quotation so that the supplier can confirm the correct orderable configuration.
What is the price of the PCA6408AHKX?
The current unit price and quantity pricing for PCA6408AHKX are not stated as a static value on this page because commercial terms can change with market conditions and order quantity. Use the Request a Quote form on this page for the current unit price, volume tiers, availability, and lead time for the exact 16-pin XQFN tape-and-reel ordering configuration.
What is the lead time for PCA6408AHKX?
The current manufacturing and fulfillment lead time for PCA6408AHKX should be confirmed through the Request a Quote form on this page. Include the required quantity, date code preference, and target shipment location in the request. This avoids confusing a general family lead time with the availability of the exact PCA6408AHKX tape-and-reel ordering configuration.
Is PCA6408AHKX currently in stock?
Current inventory status for PCA6408AHKX should be checked using the Request a Quote form on this page. Because the XQFN package and tape-and-reel suffix identify a specific orderable configuration, request the exact MPN and quantity rather than relying on a generic PCA6408AH family stock statement. The supplier can then confirm available inventory and the next possible shipment.
PCA6408AHKX vs PCAL6408AHK - which is better for a new design?
The PCAL6408AHK is the stronger choice for a new design when advanced Agile I/O features are valuable, because NXP identifies it as a pin-to-pin drop-in and software-backward-compatible upgrade to the PCA6408A. The PCA6408AHKX remains appropriate when the standard eight-port expander function is sufficient and the existing design is specifically tied to the PCA6408AHK implementation.
When should I choose PCA6408AHKX over PCAL6408AHK?
Choose the PCA6408AHKX when the design needs the established PCA6408AHK eight-channel expander function and does not require Agile I/O features such as the expanded I/O flexibility offered by PCAL6408AHK. Choose PCAL6408AHK when a manufacturer-confirmed pin-to-pin and software-compatible upgrade path is preferred or when its additional Agile I/O characteristics address a specific design requirement.
Is PCA6408AHKX suitable for a compact industrial control panel?
The PCA6408AHKX is suitable for a compact industrial control panel that needs eight additional digital lines and communicates through I2C or SMBus. Its 400 kHz bus capability reduces transfer time, while the open-drain interrupt can report input changes without continuous polling. The 1.8 mm by 2.6 mm XQFN package also helps conserve board area.
What can replace the PCA6408AHKX?
PCAL6408AHK is a directly relevant upgrade option because NXP describes it as a pin-to-pin drop-in replacement that is fully software backward-compatible with the PCA6408A. The exact orderable suffix and package must still match the installed footprint, and the Agile I/O behavior should be reviewed against the original firmware and application requirements before substitution.
What is the best NXP equivalent for PCA6408AHKX?
The best NXP-family equivalent identified for PCA6408AHKX is the PCAL6408AHK, which NXP describes as a pin-to-pin, software-backward-compatible upgrade path from the PCA6408A. It preserves the basic expander role while adding Agile I/O characteristics. Final equivalence still depends on matching the XQFN footprint, pin functions, supply limits, and interrupt behavior on the specific assembled board.

Datos de referencia de ingeniería para PCA6408AHKX — comparación, orientación de diseño e información de cumplimiento.

Guía de selección

Choose the PCA6408AHKX when a new or existing design needs a compact eight-channel I2C/SMBus expander, 400 kHz bus operation, level-translating ports, interrupt reporting, and a reset input in a 16-pin XQFN footprint. Choose the PCAL6408AHK when NXP's manufacturer-confirmed pin-to-pin and software-compatible path is valuable and the additional Agile I/O characteristics can simplify an upgrade. Retain the PCA6408AHK family configuration when only the established standard port behavior is required and reducing firmware complexity is more important than adding Agile I/O features. In either case, verify the exact package suffix, exposed-pad implementation, power-domain limits, pin functions, and interrupt behavior against the manufacturer datasheet before approving a substitution.

Comparación con alternativas

Parámetro Este producto PCA6408AHK PCAL6408AHK
Brand NXP Semiconductors NXP Semiconductors NXP Semiconductors
Package 16-pin XQFN 16-pin XQFN 16-pin XQFN
I/O Port Count 8 ports 8 ports 8 ports
Serial Interface I2C-bus and SMBus I2C-bus and SMBus I2C-bus and SMBus
Maximum Bus Frequency 400 kHz 400 kHz 400 kHz
Maximum Supply Voltage 5.5 V 5.5 V 5.5 V
Interrupt Function Open-drain INT output Open-drain INT output Open-drain INT output
Reset Function Dedicated RESET input Dedicated RESET input Dedicated RESET input
Agile I/O Features No No Yes
Drop-In Relationship PCA6408AHK device Base PCA6408AHK family ordering code Manufacturer-confirmed pin-to-pin and software-compatible upgrade

Diferenciadores clave

  • Adds Agile I/O while retaining a manufacturer-confirmed upgrade path (frente a PCA6408AHK)
  • Compact 16-pin XQFN implementation (frente a PCAL6408AHK)
  • Event-driven input monitoring (frente a PCA6408AHK)

Notas de diseño

Follow the manufacturer's 16-pin XQFN land pattern exactly, including exposed-pad geometry, mask openings, and thermal-via recommendations. The package body is only 1.8 mm by 2.6 mm, so even a small solder-mask or paste-volume error can affect assembly yield. Confirm the exact exposed-pad connection and pin numbering in the package drawing before releasing the PCB.

Place the required decoupling capacitors adjacent to the corresponding power pins and provide a low-impedance return path for every ground connection. Keep the I2C SDA and SCL traces short, route them away from noisy switching nodes, and use the pull-up values recommended by the manufacturer after accounting for bus capacitance. These measures reduce susceptibility to ringing and incomplete input transitions.

Do not assume every physical alternative has identical firmware behavior. PCAL6408AHK adds Agile I/O characteristics and is described by NXP as software backward-compatible, but its enhanced functions still require review against the existing driver and board schematic. Also verify the exact suffix and package before substitution so that the land pattern, ordering code, and exposed-pad requirements remain compatible.

Treat the open-drain interrupt output as a wired, pull-up-backed signal rather than a push-pull output. Place any interrupt pull-up near the receiving controller or according to the system topology, and keep the trace short to limit susceptibility to noise. Ensure software clears or masks the interrupt source correctly to prevent repeated service requests when a level condition remains active.

Información de cumplimiento

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Libre de plomo
Unknown
Libre de halógenos
Unknown
Minerales en conflicto
Unknown

No specific RoHS, REACH, halogen-free, or conflict-minerals status was confirmed for the PCA6408AHKX ordering configuration. Automotive qualification is not applicable to the standard industrial/consumer device designation.

Datos verificados el: 2026-11-19 — datos verificados y seleccionados por el equipo de ingeniería de componentes de XAIPART

Búsquedas relacionadas

PCA6408AHKX datasheet PCA6408AHKX pinout PCA6408AHKX datasheet pdf PCA6408AHKX equivalent PCA6408AHKX replacement PCA6408AHKX cross reference PCA6408AHKX footprint PCA6408AHKX price PCA6408AHKX stock NXP PCA6408AHKX XQFN16 PCA6408AHKX vs PCAL6408AHK PCA6408AHKX 400 kHz I2C

Componentes & términos relacionados

NXP Semiconductors PCA6408AHKX PCA6408AHK PCAL6408AHK 8-bit I/O expander level-translating I/O expander I2C-bus SMBus GPIO expander interface IC open-drain interrupt INT output RESET input 16-pin XQFN XQFN package family surface-mount package SMD semiconductor register-based control industrial control panel building automation embedded controller level translation I2C pull-up resistor
RFQ de presupuesto rápido
Complete los detalles — nuestro equipo de ventas responderá en un plazo de 24 horas
Número de pieza Fabricante Encapsulado QTY Precio objetivo Total
✓
¡Presupuesto enviado!

Responderemos a su correo electrónico en un plazo de 24 horas

1
RFQ enviado
2
Presupuesto recibido
3
Pedido realizado
4
Pago
5
Enviado
6
Entregado
Ver detalles del RFQ