PCA6408AHKX - 8-Bit I2C I/O Expander | NXP Semiconductors
料号: PCA6408AHKX ✓ 量产中PCA6408AHKX 概述
An I/O expander is an interface IC that translates serial bus commands into parallel digital input and output lines. In the system hierarchy, it sits between a microcontroller or embedded processor and external peripherals. The PCA6408AHK family provides eight configurable I/O ports, bidirectional interrupt signaling, and a reset input, making it useful when a controller has insufficient pins for switches, indicators, sensors, or relay-control signals.
The principal device features include eight I/O lines, I2C and SMBus support, operation at 100 kHz or 400 kHz, a stated maximum supply voltage of 5.5 V, and level-translating capability. The open-drain interrupt output becomes active when an input state differs from its corresponding input-port register state, allowing the connected controller to respond without continuously polling all eight pins. A dedicated reset input repeats the device's reset and initialization sequence without removing power.
The PCA6408AHKX combines a compact 16-pin XQFN package with a serial control interface intended for embedded control systems. Its level-translating architecture allows the I/O port voltage domain to be managed separately from the controller-side interface voltage when configured appropriately. This is particularly useful in systems where a low-voltage processor communicates with peripherals operating at a higher logic voltage, subject to the limits defined in the manufacturer datasheet.
Typical uses include industrial control panels, programmable logic controllers, building-automation equipment, battery-powered instrumentation, and compact consumer products. The eight ports can monitor discrete inputs or drive outputs such as status LEDs, relay-enable signals, and mode-selection controls. The interrupt output reduces unnecessary bus traffic when only a change on a monitored input requires controller attention.
PCB design should preserve the manufacturer's recommended pin, exposed-pad, decoupling, and layout constraints. Place input and output decoupling capacitors close to their associated supply pins, route the I2C bus with appropriate pull-up resistors, and confirm exposed-pad connection and thermal-via requirements during footprint review. The unusually small 1.8 mm by 2.6 mm body also makes assembly capability and solder-joint inspection important production considerations.
This product summary combines the confirmed interface, frequency, voltage, package, interrupt, and reset characteristics with practical guidance for PCB implementation, firmware control, and drop-in upgrade evaluation. It also identifies a directly related Agile I/O implementation for designs that require a pin-to-pin and software-compatible upgrade path.
直接替换替代料: PCA6408AHKX ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: PCA6408AHKX (相同外形与封装尺寸) ——差异在于 Interrupt Output.
PCA6408AHK
✅ 直接替换📋 参考替代料(不在目录中)
PCAL6408AHK
✅ 直接替换联系询价
查看数据手册 →PCA6408AHKX 规格参数
| Number of I/O Ports | 8 ports |
| Serial Interface | I2C-bus and SMBus |
| Maximum I2C Bus Frequency | 400 kHz |
| Supported Bus Frequencies | 100 kHz and 400 kHz |
| Maximum Supply Voltage | 5.5 V |
| 接口类型 | Level-translating I/O expander |
| Interrupt Output | Open-drain |
| Reset Function | Dedicated RESET input |
| Package Type | 16-pin XQFN |
| Package Dimensions | 1.8 mm x 2.6 mm |
| 安装类型 | Surface mount |
| Shipping Format | Tape and reel |
PCA6408AHKX 1.8 mm x 2.6 mm 引脚配置指南
PCA6408AHKX(1.8 mm x 2.6 mm 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: PCA6408AHKX.
请参阅 数据手册 以查看完整引脚配置。
典型应用
PCA6408AHKX 适用于 6 应用s: Compact Industrial Control Panels, Programmable Logic Controller Expansion, Building Automation Equipment, Battery-Powered Instrumentation, LED and Relay Control Interface, Consumer and IoT Peripheral Hub.
Compact Industrial Control Panels
The PCA6408AHKX suits compact control panels that need eight additional digital lines without enlarging the controller footprint. It connects to the host through I2C or SMBus at up to 400 kHz and can operate the ports as inputs, outputs, or mixed I/O according to the device configuration. The open-drain interrupt output reports an input-state change, reducing unnecessary polling when the controller is handling other real-time tasks. Its 16-pin XQFN body measures only 1.8 mm by 2.6 mm, helping preserve board area in densely populated industrial electronics.
推荐
Programmable Logic Controller Expansion
The PCA6408AHKX can add eight serial-controlled I/O lines to a programmable logic controller or embedded controller that has reached its direct GPIO limit. The bus supports 100 kHz and 400 kHz operation, while the level-translating architecture supports separate logic domains where permitted by the device limits. The interrupt output is useful when multiple inputs share a control card, allowing the controller to react to a changed state instead of repeatedly reading the bus. The compact XQFN package is particularly advantageous when expansion circuitry must fit beside existing relay or sensor interfaces.
推荐
Building Automation Equipment
The PCA6408AHKX is appropriate for building-automation controllers that interface with digital zone controls, occupancy indicators, alarms, or configurable equipment inputs. Eight ports provide a practical expansion granularity for retrofitting peripheral control functions around a central embedded processor. I2C operation up to 400 kHz permits efficient register-based control, and the interrupt output can promptly flag a changed sensor or switch state. Because the device supports level translation, it can help bridge compatible voltage domains, but the datasheet limits must be checked for each port and the power architecture.
推荐
Battery-Powered Instrumentation
The PCA6408AHKX can extend the input and output capacity of a low-power instrument without adding eight direct microcontroller pins. Serial control reduces the number of host GPIO resources consumed, while the interrupt output lets the processor sleep between relevant input events instead of polling the expander continuously. The 16-pin XQFN package measures 1.8 mm by 2.6 mm, which supports compact handheld or portable equipment layouts. Firmware should configure unused ports appropriately, and actual standby current and operating-temperature behavior should be confirmed from the manufacturer electrical characteristics.
推荐
LED and Relay Control Interface
The PCA6408AHKX provides a compact serial interface for eight discrete control lines used by status indicators, relay-enable circuits, mode selectors, or latching equipment. Register-based access through I2C or SMBus simplifies multiplexed control in boards with limited GPIO pins. At bus rates up to 400 kHz, the controller can update multiple output states efficiently, although external driver transistors are required for loads beyond the port's specified limits. The small XQFN footprint preserves routing space in densely populated control boards, and the interrupt function can also report changes on ports configured for input operation.
推荐
Consumer and IoT Peripheral Hub
The PCA6408AHKX can act as a compact peripheral hub in consumer appliances, smart-home controllers, and IoT modules. It gives an embedded controller access to eight additional digital lines for buttons, presence sensors, status indicators, or peripheral enables over I2C or SMBus. Operation at up to 400 kHz supports efficient register updates, while the open-drain interrupt output reduces communication overhead for event-driven inputs. The 1.8 mm by 2.6 mm XQFN package is useful where board area is constrained, although assembly yield and the exposed-pad layout require careful manufacturing review.
推荐
推荐产品汇总
工程参考数据: PCA6408AHKX ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | PCA6408AHK | PCAL6408AHK |
|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 16-pin XQFN | 16-pin XQFN | 16-pin XQFN |
| I/O Port Count | 8 ports | 8 ports | 8 ports |
| Serial Interface | I2C-bus and SMBus | I2C-bus and SMBus | I2C-bus and SMBus |
| Maximum Bus Frequency | 400 kHz | 400 kHz | 400 kHz |
| Maximum Supply Voltage | 5.5 V | 5.5 V | 5.5 V |
| Interrupt Function | Open-drain INT output | Open-drain INT output | Open-drain INT output |
| Reset Function | Dedicated RESET input | Dedicated RESET input | Dedicated RESET input |
| Agile I/O Features | No | No | Yes |
| Drop-In Relationship | PCA6408AHK device | Base PCA6408AHK family ordering code | Manufacturer-confirmed pin-to-pin and software-compatible upgrade |
关键差异点
- Adds Agile I/O while retaining a manufacturer-confirmed upgrade path (对比 PCA6408AHK)
- Compact 16-pin XQFN implementation (对比 PCAL6408AHK)
- Event-driven input monitoring (对比 PCA6408AHK)
设计说明
Follow the manufacturer's 16-pin XQFN land pattern exactly, including exposed-pad geometry, mask openings, and thermal-via recommendations. The package body is only 1.8 mm by 2.6 mm, so even a small solder-mask or paste-volume error can affect assembly yield. Confirm the exact exposed-pad connection and pin numbering in the package drawing before releasing the PCB.
Place the required decoupling capacitors adjacent to the corresponding power pins and provide a low-impedance return path for every ground connection. Keep the I2C SDA and SCL traces short, route them away from noisy switching nodes, and use the pull-up values recommended by the manufacturer after accounting for bus capacitance. These measures reduce susceptibility to ringing and incomplete input transitions.
Do not assume every physical alternative has identical firmware behavior. PCAL6408AHK adds Agile I/O characteristics and is described by NXP as software backward-compatible, but its enhanced functions still require review against the existing driver and board schematic. Also verify the exact suffix and package before substitution so that the land pattern, ordering code, and exposed-pad requirements remain compatible.
Treat the open-drain interrupt output as a wired, pull-up-backed signal rather than a push-pull output. Place any interrupt pull-up near the receiving controller or according to the system topology, and keep the trace short to limit susceptibility to noise. Ensure software clears or masks the interrupt source correctly to prevent repeated service requests when a level condition remains active.
合规信息
No specific RoHS, REACH, halogen-free, or conflict-minerals status was confirmed for the PCA6408AHKX ordering configuration. Automotive qualification is not applicable to the standard industrial/consumer device designation.