Texas Instruments

PCA9534DWG4 - 8-Bit I2C I/O Expander | Texas Instruments

N.º de pieza: PCA9534DWG4 ✓ Activo
2.3 V to 5.5 V Vdss 16 pins Package 400 kHz Speed
MOQ: 1 |

PCA9534DWG4 Descripción general

Texas Instruments PCA9534DWG4 is an 8-bit CMOS I/O expander for I2C-bus and SMBus systems, operating from 2.3 V to 5.5 V with a 400 kHz bus clock in a 16-pin SOIC package. It adds eight configurable general-purpose parallel I/O ports to a host controller while providing 5 V tolerant inputs, individual port configuration, an interrupt output, and dedicated configuration registers. The wide supply-voltage range makes the device suitable for both 3.3 V and 5 V embedded systems.

An I2C I/O expander belongs to the parallel-interface hierarchy: GPIO controller → I/O expander → I2C or SMBus peripheral. Its purpose is to increase the number of digital input and output lines available from a microcontroller or other bus host without adding a large number of host pins. Each expander port can be configured independently as an input or output, allowing the same device to support control signals, discrete status inputs, and external bus connections.

The PCA9534DWG4 provides higher drive capability than earlier I2C port expanders, along with 5 V tolerant I/O operation and lower supply current. Individual I/O configuration allows each of the eight ports to operate in the direction required by the application. An active-low interrupt output provides an efficient way to alert the host when a change occurs on a monitored input, reducing unnecessary polling.

The device uses the I2C or SMBus protocol at up to 400 kHz and includes input, output, port, and configuration registers. Address selection supports multiple expander devices on the same bus when the hardware address pins are configured appropriately. This makes the PCA9534 family suitable for structured industrial controls, embedded accessories, and compact control boards where pin count is constrained.

Typical uses include reading switch banks, driving discrete LEDs or relay-control inputs, expanding sensor-control interfaces, and supporting bus-controlled peripheral boards. It is especially useful in industrial equipment, test and measurement systems, portable instruments, and consumer accessories that need additional GPIO without changing the host microcontroller.

Design the PCB with the I2C pull-up resistors positioned close to the bus master or the most distant device, and confirm that their total resistance matches the bus capacitance and clock rate. Keep the interrupt trace short and route it away from high-current switching nodes. Because the SOIC package has exposed lead spacing, verify the land pattern and solder-assembly process against the manufacturer package drawing.

This page combines manufacturer specifications, practical interface guidance, drop-in replacement analysis, and an application-by-application selection framework. It is intended to help engineers confirm electrical compatibility, package fit, bus behavior, and sourcing requirements before placing PCA9534DWG4 into a production design.

Alternativas directas para PCA9534DWG4 — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.

Variantes de esta serie

Modelos de la misma serie compatibles directamente con PCA9534DWG4 (mismo factor de forma y huella) — difiere en Device Type, Number of I/O Ports, Package.

Texas Instruments
Device Type: 8-bit I2C/SMBus I/O expander
Number of I/O Ports: 8
Package: 16-SOIC
Comparar con PCA9534DWG4 →

PCA9534DW

✅ Sustitución directa ⚠️ Especificaciones sin verificar
Texas Instruments
📦 SOIC-16
8-bit I2C/SMBus I/O expander · 8 · 2.3 V to 5.5 V · 400 kHz · I2C/SMBus · Push-pull · Yes · Yes

Consulte el precio

Ver hoja de datos →

PCA9534D,118

✅ Sustitución directa ⚠️ Especificaciones sin verificar
📦 SOIC-16
Uses a comma-separated ordering code instead of the complete PCA9534DWG4 suffix; the device remains in the same 8-bit PCA9534 SOIC-16 family with matching core electrical parameters

📋 Alternativa de referencia (no en el catálogo)

PCA9534DWG4 Especificaciones

Number of I/O Ports 8 ports
Tipo de interfaz I2C-bus and SMBus
Maximum Bus Clock Frequency 400 kHz
Supply Voltage Range 2.3 V to 5.5 V
I/O Pin Count 8 pins
Total Package Pin Count 16 pins
I/O Tolerance 5 V tolerant
Rango de temperatura de funcionamiento -40 °C to +85 °C
Device Technology CMOS
Device Type General-purpose parallel I/O expander
Encapsulado 16-SOIC, 7.50 mm width
Tipo de montaje Surface mount
Interrupt Output Yes
Configuration Registers Yes
Individual I/O Configuration Yes
I/O Drive Capability Enhanced high-current output drive
Estado RoHS Compliant
Operating Temperature Minimum -40 °C
Operating Temperature Maximum +85 °C

Guía de configuración de pines de PCA9534DWG4 16-soic, 7.50 mm width

Configuración de pines para PCA9534DWG4 (encapsulado 16-soic, 7.50 mm width). La numeración de pines, las funciones y los diagramas de conexión se definen en la hoja de datos del fabricante. Consúltela para conocer el footprint exacto y las directrices de soldadura.

Diagrama de patillaje del encapsulado 16-soic, 7.50 mm width para PCA9534DWG4

No hay datos detallados de patillaje disponibles para PCA9534DWG4.

Consulte la hoja de datos para ver la configuración completa de patillas.

Aplicaciones típicas

PCA9534DWG4 es adecuado para 6 aplicacións: Industrial Control and Relay Interface, LED and Backlight Control, Test and Measurement Front Panels, Embedded Sensor and Peripheral Hub, Portable Instrument Control, Communications and Network Equipment.

🏭

Industrial Control and Relay Interface

The PCA9534DWG4 suits industrial control boards that need additional discrete control and status signals without consuming a large number of controller pins. Its eight ports can be individually configured as inputs or outputs, allowing one device to operate mixed input and output channels. The 2.3 V to 5.5 V supply range supports common industrial logic rails, while the interrupt output can notify the controller when an input changes. The I2C or SMBus interface operates up to 400 kHz and reduces wiring compared with direct GPIO expansion. In a relay-control design, keep inductive loads and switching nodes away from the expander to reduce ground bounce and unintended transitions.

💡

LED and Backlight Control

The PCA9534DWG4 can expand a controller into a compact LED or backlight command interface by driving discrete logic inputs, driver-enable signals, or mode-selection lines. Eight independently configurable ports provide more flexibility than using fixed output groups, and the interrupt output can report button or fault-line changes on an input port. Its 400 kHz I2C-bus capability provides sufficient bandwidth for modest status and control traffic. Because LED drivers may contain high-current or switching transitions, use the expander for logic-level control rather than directly driving power LEDs unless every drive, current, and voltage requirement is explicitly satisfied.

🔧

Test and Measurement Front Panels

The PCA9534DWG4 is useful in test and measurement instruments that need additional front-panel keys, indicator controls, range-selection signals, or digital status inputs. The eight ports can be mixed between inputs and outputs, reducing the number of host-controller connections needed for operator controls. A bus frequency of up to 400 kHz allows the controller to update several controls quickly, while the interrupt output supports immediate notification of operator actions. The 16-pin SOIC package also fits densely populated instrument electronics. Keep sensitive analog and measurement circuitry away from long switch-node routes, and use the interrupt pin to request a debounced panel scan rather than treating every transition as an immediate command.

🧩

Embedded Sensor and Peripheral Hub

The PCA9534DWG4 can serve as an auxiliary hub for addressable sensors, peripheral enables, and discrete status lines in an embedded system. Eight general-purpose ports make it practical to share control functions among multiple functional blocks while preserving the host processor's limited GPIO capacity. The device supports both 3.3 V and 5 V systems within its 2.3 V to 5.5 V operating range, and its 5 V tolerant I/O characteristic simplifies interfacing with appropriately designed external logic. Firmware should read the input-port register after an interrupt and confirm that the relevant status bits have actually changed, preventing repeated handling of level-triggered conditions.

📱

Portable Instrument Control

Battery-powered instruments can use the PCA9534DWG4 to consolidate low-speed control signals without adding a large number of pins to the main controller. The lower supply current characteristic is valuable in portable equipment, and the device can operate across a 2.3 V to 5.5 V range for mixed-voltage logic systems. An interrupt output enables the controller to sleep between user interactions instead of polling eight input lines continuously. For a compact handheld design, choose pull-up values that minimize current while maintaining a valid rise time at the required bus capacitance. Confirm low-voltage operation, output leakage, and sleep-mode requirements against the manufacturer electrical-characteristics table before finalizing the battery budget.

🌐

Communications and Network Equipment

The PCA9534DWG4 can expand control and status lines in network-access equipment, interface modules, and communication boards. Its I2C-bus or SMBus connection up to 400 kHz suits moderate-speed control traffic, and the eight ports can drive module enables, fault indicators, or read discrete link-status signals. The interrupt output helps the system react to external events without continuously polling the expander. When several expanders share the bus, assign addresses deliberately and review pull-up placement to prevent excessive total bus resistance. Keep the interrupt and I2C routing away from high-speed communication traces and power-converter switching nodes, especially on densely populated line cards.

What is the PCA9534DWG4?
The PCA9534DWG4 is an 8-bit CMOS I/O expander that connects to an I2C-bus or SMBus host and provides eight independently configurable general-purpose I/O ports. According to the Texas Instruments product page, it operates from 2.3 V to 5.5 V, supports bus speeds up to 400 kHz, and includes interrupt and configuration registers in a 16-pin SOIC package.
What is the operating voltage of the PCA9534DWG4?
The PCA9534DWG4 operates from 2.3 V to 5.5 V. According to the Texas Instruments product information, this range supports both 3.3 V and 5 V systems, while the device's 5 V tolerant I/O structure allows its ports to interface with suitable external logic levels. Confirm the exact voltage and current limits in the manufacturer datasheet before applying the inputs.
How many GPIO pins can the PCA9534DWG4 add?
The PCA9534DWG4 adds eight general-purpose parallel I/O ports to an I2C or SMBus host. Each port can be configured independently as an input or output, and the device also provides an interrupt output for change notification. The complete assembly uses 16 package pins, including supply, ground, bus, address-selection, interrupt, and eight I/O connections.
What is the maximum I2C clock frequency of the PCA9534DWG4?
The PCA9534DWG4 supports I2C-bus and SMBus operation at a maximum clock frequency of 400 kHz. According to the manufacturer product page, the device also includes input, output, port, and configuration registers. Board-level pull-up selection must support both the target bus speed and the total capacitance of the connected devices.
Does the PCA9534DWG4 include an interrupt output?
Yes, the PCA9534DWG4 includes an interrupt output for signaling input-port changes to the host controller. Texas Instruments describes the device as an 8-bit I/O expander with interrupt and configuration registers. This allows the controller to avoid continuous status polling, provided the interrupt polarity and source configuration are handled correctly in software.
Is the PCA9534DWG4 pin-compatible with the PCA9534DW?
The PCA9534DW is a same-family Texas Instruments option associated with the PCA9534 16-pin SOIC implementation and is the closest same-brand drop-in candidate. The PCA9534DWG4 includes the full ordering suffix for this device, while PCA9534DW is the shorter ordering designation. Review the package drawing and ordering table before production release because suffix and shipment-form differences can affect labeling or logistics.
PCA9534DWG4 vs PCA9534DW: which one should I choose?
Choose the PCA9534DWG4 when the bill of materials specifically requires that complete Texas Instruments ordering code and its associated green device designation. The PCA9534DW is the shorter catalog designation for the closely related 16-pin SOIC family member. Both are associated with the PCA9534 8-bit I2C/SMBus expander, but the exact suffix and shipment form should be checked against the approved ordering table.
When should I choose the PCA9534DWG4 over another 8-bit I/O expander?
Choose the PCA9534DWG4 when the design needs eight configurable I/Os, a 2.3 V to 5.5 V supply range, 400 kHz I2C or SMBus operation, 5 V tolerant I/O, and an interrupt output in a 16-pin SOIC footprint. Select another expander instead when it offers a different bus speed, more I/O channels, lower voltage operation, a smaller package, or a non-SOIC land pattern required by the PCB.
What can replace the PCA9534DWG4?
The PCA9534DW is the closest same-brand replacement candidate because it belongs to the PCA9534 family and uses the 16-pin SOIC implementation. The PCA9534D,118 is another catalog form identified in the cross-reference results. Neither should be substituted solely from the suffix: verify pin functions, address selection, electrical limits, package dimensions, and shipment form in the manufacturer ordering information.
What is the best NXP equivalent for the PCA9534DWG4?
No cross-brand NXP equivalent is established as a verified pin-to-pin drop-in replacement for the PCA9534DWG4 in the available cross-reference information. The Texas Instruments family candidates are the only close matches identified. Use the manufacturer cross-reference tool to locate current NXP options, then compare pinout, supply range, bus speed, interrupt behavior, and package dimensions before treating any part as a replacement.
Is the PCA9534DWG4 suitable for a 3.3 V embedded system?
Yes, the PCA9534DWG4 is suitable for a 3.3 V embedded system because its specified operating range includes 3.3 V. The device supports an I2C-bus or SMBus connection at up to 400 kHz and provides eight configurable I/O ports. The host bus pull-ups should be sized for 3.3 V, and every connected output or signal source must remain within the applicable input and output limits.
Where can I download the PCA9534DWG4 datasheet PDF?
The PCA9534DWG4 datasheet is available through the Texas Instruments PCA9534 product page at https://www.ti.com/product/PCA9534. Select the device and documentation tab to open the manufacturer datasheet. The pin-description table, register map, electrical characteristics, and package drawing should be used for final PCB and firmware design.
Where can I find the PCA9534DWG4 pinout?
The PCA9534DWG4 pinout is found in the pin-configuration section of the Texas Instruments manufacturer datasheet. The device uses a 16-pin SOIC package with eight I/O pins plus power, ground, bus, address-selection, and interrupt connections. Use the package drawing for physical orientation and the pin-description table for signal assignment; do not infer connections solely from the package outline.
Where can I buy the PCA9534DWG4 online?
Use the Request a Quote form on this XAIPART product page to request the PCA9534DWG4, current availability, and lead time. The form is the preferred route for an exact-order quotation and avoids discrepancies between generic catalog pricing and the requested configuration. Include the SOIC-16 package, quantity, target date, and any required production or traceability documentation in the request.
What is the price of the PCA9534DWG4?
Current pricing for the PCA9534DWG4 should be requested through the Request a Quote form on this page. Price and availability can change with order quantity, inventory, date, and shipment requirements, so a static figure may not reflect the terms available for your BOM. Provide the required quantity and target delivery date to receive the applicable quotation.
What is the lead time and stock status for the PCA9534DWG4?
Request the current lead time, minimum order quantity, and stock status through the Request a Quote form on this page. The form connects the inquiry to the exact PCA9534DWG4 ordering code and current supply conditions. For production planning, include your required delivery date, annual usage, approved vendor requirements, and whether unbroken-date labeling or additional documentation is required.

Datos de referencia de ingeniería para PCA9534DWG4 — comparación, orientación de diseño e información de cumplimiento.

Guía de selección

Choose the PCA9534DWG4 when the bill of materials specifies that complete Texas Instruments ordering code and the board requires eight configurable I/O ports, a 2.3 V to 5.5 V supply range, I2C or SMBus operation at up to 400 kHz, and an interrupt output in a 16-pin SOIC package. The PCA9534DW is the closest same-brand alternative when the shorter ordering designation is acceptable and approved by the procurement specification. The PCA9534D,118 is another same-family catalog form that can serve as a drop-in candidate after its ordering, marking, and shipment requirements are confirmed. Do not select a different-bus or different-pin-count expander as a direct replacement: devices with four extra GPIOs, a different address scheme, or another package can require firmware and PCB changes even when their advertised functions appear similar.

Comparación con alternativas

Parámetro Este producto PCA9534DW PCA9534D,118
Package 16-SOIC, 7.50 mm width 16-SOIC 16-SOIC
Brand Texas Instruments Texas Instruments Texas Instruments
Number of I/O Ports 8 8 8
Interface I2C-bus and SMBus I2C-bus and SMBus I2C-bus and SMBus
Maximum Bus Clock Frequency 400 kHz 400 kHz 400 kHz
Supply Voltage Range 2.3 V to 5.5 V 2.3 V to 5.5 V 2.3 V to 5.5 V
Interrupt Output Yes Yes Yes
Configuration Registers Yes Yes Yes
Operating Temperature Range -40 °C to +85 °C -40 °C to +85 °C -40 °C to +85 °C
Special Ordering Designation PCA9534DWG4 PCA9534DW PCA9534D,118

Diferenciadores clave

  • Eight independently configurable ports with interrupt notification (frente a PCA9534DW)
  • Wide operating-voltage range (frente a PCA9534D,118)
  • 400 kHz I2C and SMBus support (frente a PCA9534DW)
  • 5 V tolerant I/O and improved drive capability (frente a PCA9534D,118)

Notas de diseño

Treat the I2C pull-up network as part of the bus design rather than a collection of independent resistors. Calculate the equivalent pull-up resistance from all devices on the segment, verify the rise time at the highest bus capacitance, and ensure the resulting high level is valid for every connected device. Place the pull-ups where they can support the full physical bus segment without creating excessive parallel resistance.

Route SDA, SCL, and the interrupt output away from switching nodes, relay drivers, and high-current output edges. Keep the bus traces short, use a continuous ground reference, and place any required series damping close to the driving device. The interrupt line should be routed away from sources of transient noise so that control firmware does not repeatedly process false input changes.

Use the 16-pin wide-SOIC land pattern and confirm body width, lead pitch, and courtyard clearance against the manufacturer package drawing. Maintain adequate spacing from tall adjacent components because the SOIC-16 body is wider than a narrow TSSOP-16. Provide a stable ground connection near the supply and ground pins, and avoid placing test points or tall sockets where they interfere with the reflow profile.

After an interrupt is asserted, read the input-port register and determine which bits changed before clearing the interrupt condition. Level-held inputs can otherwise cause repeated service calls. Software should also account for the address-selection pins before writing configuration registers, particularly when more than one expander is installed on the same I2C or SMBus segment.

Información de cumplimiento

RoHS
Compliant
REACH
Unknown
AEC-Q100
Unknown
Libre de plomo
Unknown
Libre de halógenos
Unknown
Minerales en conflicto
Unknown

The LCSC product result identifies the exact MPN as RoHS compliant. REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status require confirmation from the applicable manufacturer documentation.

Datos verificados el: 2026-11-14 — datos verificados y seleccionados por el equipo de ingeniería de componentes de XAIPART

Búsquedas relacionadas

PCA9534DWG4 datasheet PCA9534DWG4 pinout PCA9534DWG4 datasheet pdf PCA9534DWG4 equivalent PCA9534DWG4 replacement PCA9534DWG4 cross reference PCA9534DWG4 price PCA9534DWG4 stock Texas Instruments PCA9534DWG4 PCA9534 8-bit I2C expander PCA9534 16-SOIC pinout PCA9534DWG4 vs PCA9534DW

Componentes & términos relacionados

Texas Instruments PCA9534DWG4 PCA9534 PCA9534DW PCA9534D,118 I/O expander general-purpose I/O GPIO expander I2C-bus SMBus CMOS SOIC-16 surface mount 5 V tolerant I/O 400 kHz bus clock interrupt output configuration registers input-port register output-port register I2C pull-up resistors industrial control test and measurement LED control embedded system communications equipment
RFQ de presupuesto rápido
Complete los detalles — nuestro equipo de ventas responderá en un plazo de 24 horas
Número de pieza Fabricante Encapsulado QTY Precio objetivo Total
✓
¡Presupuesto enviado!

Responderemos a su correo electrónico en un plazo de 24 horas

1
RFQ enviado
2
Presupuesto recibido
3
Pedido realizado
4
Pago
5
Enviado
6
Entregado
Ver detalles del RFQ