PCA9534DWG4 - 8-Bit I2C I/O Expander | Texas Instruments
부품 번호: PCA9534DWG4 ✓ 활성PCA9534DWG4 개요
An I2C I/O expander belongs to the parallel-interface hierarchy: GPIO controller → I/O expander → I2C or SMBus peripheral. Its purpose is to increase the number of digital input and output lines available from a microcontroller or other bus host without adding a large number of host pins. Each expander port can be configured independently as an input or output, allowing the same device to support control signals, discrete status inputs, and external bus connections.
The PCA9534DWG4 provides higher drive capability than earlier I2C port expanders, along with 5 V tolerant I/O operation and lower supply current. Individual I/O configuration allows each of the eight ports to operate in the direction required by the application. An active-low interrupt output provides an efficient way to alert the host when a change occurs on a monitored input, reducing unnecessary polling.
The device uses the I2C or SMBus protocol at up to 400 kHz and includes input, output, port, and configuration registers. Address selection supports multiple expander devices on the same bus when the hardware address pins are configured appropriately. This makes the PCA9534 family suitable for structured industrial controls, embedded accessories, and compact control boards where pin count is constrained.
Typical uses include reading switch banks, driving discrete LEDs or relay-control inputs, expanding sensor-control interfaces, and supporting bus-controlled peripheral boards. It is especially useful in industrial equipment, test and measurement systems, portable instruments, and consumer accessories that need additional GPIO without changing the host microcontroller.
Design the PCB with the I2C pull-up resistors positioned close to the bus master or the most distant device, and confirm that their total resistance matches the bus capacitance and clock rate. Keep the interrupt trace short and route it away from high-current switching nodes. Because the SOIC package has exposed lead spacing, verify the land pattern and solder-assembly process against the manufacturer package drawing.
This page combines manufacturer specifications, practical interface guidance, drop-in replacement analysis, and an application-by-application selection framework. It is intended to help engineers confirm electrical compatibility, package fit, bus behavior, and sourcing requirements before placing PCA9534DWG4 into a production design.
드롭인 대체품: PCA9534DWG4 — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: PCA9534DWG4 (동일 폼 팩터 및 풋프린트) — 차이점: Device Type, Number of I/O Ports, Package.
PCA9534DW
✅ 드롭인 ⚠️ 사양 미검증가격 문의
데이터시트 보기 →PCA9534D,118
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
PCA9534DWG4 사양
| Number of I/O Ports | 8 ports |
| 인터페이스 유형 | I2C-bus and SMBus |
| Maximum Bus Clock Frequency | 400 kHz |
| Supply Voltage Range | 2.3 V to 5.5 V |
| I/O Pin Count | 8 pins |
| Total Package Pin Count | 16 pins |
| I/O Tolerance | 5 V tolerant |
| 동작 온도 범위 | -40 °C to +85 °C |
| Device Technology | CMOS |
| Device Type | General-purpose parallel I/O expander |
| 패키지 | 16-SOIC, 7.50 mm width |
| 실장 유형 | Surface mount |
| Interrupt Output | Yes |
| Configuration Registers | Yes |
| Individual I/O Configuration | Yes |
| I/O Drive Capability | Enhanced high-current output drive |
| RoHS 상태 | Compliant |
| Operating Temperature Minimum | -40 °C |
| Operating Temperature Maximum | +85 °C |
PCA9534DWG4 16-soic, 7.50 mm width 핀 구성 가이드
PCA9534DWG4(16-soic, 7.50 mm width 패키지)의 핀 구성입니다. 핀 번호, 기능, 연결 다이어그램은 제조사 데이터시트에 정의되어 있습니다. 정확한 풋프린트와 솔더링 지침은 해당 문서를 참조하십시오.
다음에 대한 상세 핀아웃 데이터 없음: PCA9534DWG4.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
PCA9534DWG4 적합 용도: 6 애플리케이션s: Industrial Control and Relay Interface, LED and Backlight Control, Test and Measurement Front Panels, Embedded Sensor and Peripheral Hub, Portable Instrument Control, Communications and Network Equipment.
Industrial Control and Relay Interface
The PCA9534DWG4 suits industrial control boards that need additional discrete control and status signals without consuming a large number of controller pins. Its eight ports can be individually configured as inputs or outputs, allowing one device to operate mixed input and output channels. The 2.3 V to 5.5 V supply range supports common industrial logic rails, while the interrupt output can notify the controller when an input changes. The I2C or SMBus interface operates up to 400 kHz and reduces wiring compared with direct GPIO expansion. In a relay-control design, keep inductive loads and switching nodes away from the expander to reduce ground bounce and unintended transitions.
LED and Backlight Control
The PCA9534DWG4 can expand a controller into a compact LED or backlight command interface by driving discrete logic inputs, driver-enable signals, or mode-selection lines. Eight independently configurable ports provide more flexibility than using fixed output groups, and the interrupt output can report button or fault-line changes on an input port. Its 400 kHz I2C-bus capability provides sufficient bandwidth for modest status and control traffic. Because LED drivers may contain high-current or switching transitions, use the expander for logic-level control rather than directly driving power LEDs unless every drive, current, and voltage requirement is explicitly satisfied.
Test and Measurement Front Panels
The PCA9534DWG4 is useful in test and measurement instruments that need additional front-panel keys, indicator controls, range-selection signals, or digital status inputs. The eight ports can be mixed between inputs and outputs, reducing the number of host-controller connections needed for operator controls. A bus frequency of up to 400 kHz allows the controller to update several controls quickly, while the interrupt output supports immediate notification of operator actions. The 16-pin SOIC package also fits densely populated instrument electronics. Keep sensitive analog and measurement circuitry away from long switch-node routes, and use the interrupt pin to request a debounced panel scan rather than treating every transition as an immediate command.
Embedded Sensor and Peripheral Hub
The PCA9534DWG4 can serve as an auxiliary hub for addressable sensors, peripheral enables, and discrete status lines in an embedded system. Eight general-purpose ports make it practical to share control functions among multiple functional blocks while preserving the host processor's limited GPIO capacity. The device supports both 3.3 V and 5 V systems within its 2.3 V to 5.5 V operating range, and its 5 V tolerant I/O characteristic simplifies interfacing with appropriately designed external logic. Firmware should read the input-port register after an interrupt and confirm that the relevant status bits have actually changed, preventing repeated handling of level-triggered conditions.
Portable Instrument Control
Battery-powered instruments can use the PCA9534DWG4 to consolidate low-speed control signals without adding a large number of pins to the main controller. The lower supply current characteristic is valuable in portable equipment, and the device can operate across a 2.3 V to 5.5 V range for mixed-voltage logic systems. An interrupt output enables the controller to sleep between user interactions instead of polling eight input lines continuously. For a compact handheld design, choose pull-up values that minimize current while maintaining a valid rise time at the required bus capacitance. Confirm low-voltage operation, output leakage, and sleep-mode requirements against the manufacturer electrical-characteristics table before finalizing the battery budget.
Communications and Network Equipment
The PCA9534DWG4 can expand control and status lines in network-access equipment, interface modules, and communication boards. Its I2C-bus or SMBus connection up to 400 kHz suits moderate-speed control traffic, and the eight ports can drive module enables, fault indicators, or read discrete link-status signals. The interrupt output helps the system react to external events without continuously polling the expander. When several expanders share the bus, assign addresses deliberately and review pull-up placement to prevent excessive total bus resistance. Keep the interrupt and I2C routing away from high-speed communication traces and power-converter switching nodes, especially on densely populated line cards.
엔지니어링 참조 데이터: PCA9534DWG4 — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | PCA9534DW | PCA9534D,118 |
|---|---|---|---|
| Package | 16-SOIC, 7.50 mm width | 16-SOIC | 16-SOIC |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Number of I/O Ports | 8 | 8 | 8 |
| Interface | I2C-bus and SMBus | I2C-bus and SMBus | I2C-bus and SMBus |
| Maximum Bus Clock Frequency | 400 kHz | 400 kHz | 400 kHz |
| Supply Voltage Range | 2.3 V to 5.5 V | 2.3 V to 5.5 V | 2.3 V to 5.5 V |
| Interrupt Output | Yes | Yes | Yes |
| Configuration Registers | Yes | Yes | Yes |
| Operating Temperature Range | -40 °C to +85 °C | -40 °C to +85 °C | -40 °C to +85 °C |
| Special Ordering Designation | PCA9534DWG4 | PCA9534DW | PCA9534D,118 |
주요 차별점
- Eight independently configurable ports with interrupt notification (vs PCA9534DW)
- Wide operating-voltage range (vs PCA9534D,118)
- 400 kHz I2C and SMBus support (vs PCA9534DW)
- 5 V tolerant I/O and improved drive capability (vs PCA9534D,118)
설계 노트
Treat the I2C pull-up network as part of the bus design rather than a collection of independent resistors. Calculate the equivalent pull-up resistance from all devices on the segment, verify the rise time at the highest bus capacitance, and ensure the resulting high level is valid for every connected device. Place the pull-ups where they can support the full physical bus segment without creating excessive parallel resistance.
Route SDA, SCL, and the interrupt output away from switching nodes, relay drivers, and high-current output edges. Keep the bus traces short, use a continuous ground reference, and place any required series damping close to the driving device. The interrupt line should be routed away from sources of transient noise so that control firmware does not repeatedly process false input changes.
Use the 16-pin wide-SOIC land pattern and confirm body width, lead pitch, and courtyard clearance against the manufacturer package drawing. Maintain adequate spacing from tall adjacent components because the SOIC-16 body is wider than a narrow TSSOP-16. Provide a stable ground connection near the supply and ground pins, and avoid placing test points or tall sockets where they interfere with the reflow profile.
After an interrupt is asserted, read the input-port register and determine which bits changed before clearing the interrupt condition. Level-held inputs can otherwise cause repeated service calls. Software should also account for the address-selection pins before writing configuration registers, particularly when more than one expander is installed on the same I2C or SMBus segment.
규정 준수 정보
The LCSC product result identifies the exact MPN as RoHS compliant. REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status require confirmation from the applicable manufacturer documentation.