PCA9538D - 8-Bit I2C GPIO Expander | NXP Semiconductors
N.º de pieza: PCA9538D ✗ Fin de vidaPCA9538D Descripción general
An I/O expander is a peripheral integrated circuit that increases the number of inputs and outputs available to a host controller without requiring a large number of microcontroller pins. In the broader semiconductor hierarchy, the PCA9538D is an I2C interface IC, a GPIO expander, and ultimately a general-purpose semiconductor. It is useful when a system needs more control or status signals than the host microcontroller can expose directly.
The PCA9538 includes an 8-bit configuration register, input port register, output port register, and polarity-inversion register. Each port bit can be configured independently as an input or output. The interrupt output signals a change on a configured input, while the reset input restores the registers to their power-on state. The A0 and A1 address pins allow up to four devices to share one I2C bus.
Its 16-pin CMOS implementation is designed for low-power embedded control. The 2.3 V to 5.5 V operating range covers common 3.3 V and 5 V systems, while the 400 kHz I2C limit supports standard embedded peripheral buses. The SOIC-16 surface-mount package simplifies assembly on conventional through-hole-compatible PCB layouts and provides adequate spacing between pins for hand rework and inspection.
Typical uses include ACPI power-control systems, sensor and switch interfaces, relay or fan controls, LED status and indicator circuits, key scanners, and general-purpose industrial control boards. The interrupt output can reduce polling by notifying the host controller when a monitored input changes, provided the host firmware handles the resulting interrupt and reads the appropriate status register.
PCB design should preserve clear access to SDA, SCL, RESET, INT, and the two address pins. Pull-up resistors are normally required on the open-drain I2C lines and should be selected from the bus capacitance, voltage, and required rise-time calculations. Confirm the A0 and A1 states before multiple expanders share a bus so that each device has a unique address.
This product overview combines the manufacturer functional description with package, interface, register, and application guidance for engineers evaluating the PCA9538D as a legacy embedded-system I/O expansion solution.
Alternativas directas para PCA9538D — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
PCA9538DGVR
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
PCA9538D,112
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
PCA9538D,118
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
PCA9538D
✅ Sustitución directaConsulte el precio
Ver hoja de datos →PCA9538D Especificaciones
| Device Type | 8-bit CMOS I/O expander |
| Number of I/O Pins | 8 |
| Supply Voltage Range | 2.3 V to 5.5 V |
| I2C Bus Speed | Up to 400 kHz |
| Supported Bus | I2C-bus and SMBus |
| Logic Voltage | 2.3 V to 5.5 V CMOS |
| Total Package Pins | 16 pins |
| Encapsulado | 16-pin SOIC |
| Configuration Register | 8 bits |
| Input Port Register | 8 bits |
| Output Port Register | 8 bits |
| Polarity Inversion Register | 8 bits |
| Hardware Address Inputs | 2 inputs, A0 and A1 |
| Maximum Devices per I2C Bus | 4 devices |
| Interrupt Output | Active-low INT output |
| Reset Input | Active-low RESET input |
| Tipo de montaje | Surface mount |
Configuración de pines de PCA9538D
| Pin 1 | A0 — Address input A0 |
| Pin 2 | A1 — Address input A1 |
| Pin 3 | RESET — Active-low reset input |
| Pin 4 | VSS — Ground reference |
| Pin 5 | P0 — General-purpose I/O port 0 |
| Pin 6 | P1 — General-purpose I/O port 1 |
| Pin 7 | P2 — General-purpose I/O port 2 |
| Pin 8 | P3 — General-purpose I/O port 3 |
| Pin 9 | P4 — General-purpose I/O port 4 |
| Pin 10 | P5 — General-purpose I/O port 5 |
| Pin 11 | P6 — General-purpose I/O port 6 |
| Pin 12 | P7 — General-purpose I/O port 7 |
| Pin 13 | INT — Active-low interrupt output |
| Pin 14 | VDD — Positive supply voltage |
| Pin 15 | SCL — Serial clock input |
| Pin 16 | SDA — Serial data input/output |
Aplicaciones típicas
PCA9538D es adecuado para 6 aplicacións: ACPI Power-Control Interface, Industrial Sensor and Switch Interface, LED Status and Indicator Control, Fan and Relay Control, Embedded Key and Button Scanner, Legacy Motherboard and Peripheral Control.
ACPI Power-Control Interface
The PCA9538D fits legacy ACPI-compatible control boards where a compact controller must operate several power-related signals. Its eight configurable I/O lines can represent enable, sleep, power-good, or system-state functions, while the 2.3 V to 5.5 V range supports common embedded supply levels. The host communicates through I2C or SMBus at up to 400 kHz, reducing parallel GPIO demand on the system controller. Because the interrupt output can announce input changes, the firmware can react to a power or status event without continuously polling all eight lines. During implementation, assign each signal through the configuration register and confirm active-high or active-low requirements using the polarity-inversion register.
Recomendado
Industrial Sensor and Switch Interface
The PCA9538D is suitable for collecting digital status from sensors, selectors, limit switches, and operator push buttons in industrial equipment. Each of the eight ports can be configured independently, allowing mixed input and output use on the same expander. With I2C operation up to 400 kHz, the device provides adequate bus bandwidth for low-rate supervisory signals rather than high-frequency sampling. The interrupt output provides event notification when a configured input changes, allowing the controller to service the bus only when needed. Firmware should first read the input register, then determine which state transition caused the interrupt, and finally clear the source as required by the NXP manufacturer datasheet.
Recomendado
LED Status and Indicator Control
The PCA9538D can expand a controller's available outputs for LED status panels, fault indicators, and system-health displays. Its eight independently controlled output lines reduce the number of direct host GPIO pins required for visual status reporting, while the 2.3 V to 5.5 V operating range supports both 3.3 V and 5 V logic systems. The output-port register allows firmware to update multiple indicators through one I2C transaction sequence. When driving LEDs, calculate resistor values from the actual LED forward voltage and supply level, and confirm whether the application requires source or current sinking. The interrupt and reset functions remain useful for coordinated startup and fault-state initialization.
Recomendado
Fan and Relay Control
The PCA9538D can provide compact control outputs for fans, relays, latches, and other low-rate actuators in embedded equipment. Its eight independently configurable ports allow several actuator commands to share one I2C connection, while the interrupt line can monitor feedback inputs in the same device. The 400 kHz interface is more than sufficient for supervisory commands and status polling, but it is not intended for high-speed pulse generation or precise timing. External driver circuits may still be needed for relay coils, inductive loads, or fan motors. Use appropriate flyback protection, transient suppression, and current limiting, and verify that the port's output limits match the selected load driver.
Recomendado
Embedded Key and Button Scanner
The PCA9538D can expand a microcontroller's limited input capacity for keypad rows, panel buttons, and mechanical selectors. Eight configurable inputs reduce wiring to the host and allow the controller to handle several switches without dedicating one GPIO pin to each signal. The interrupt output is particularly useful for low-rate human-interface inputs because the controller can remain idle until a button state changes. Firmware should configure debounce handling in software or external circuitry, account for contact bounce, and use the polarity-inversion register when the board presents active-low button signals. The device's 2.3 V to 5.5 V range supports common control-board logic levels.
Recomendado
Legacy Motherboard and Peripheral Control
The PCA9538D remains useful in service and modernization of legacy motherboard and peripheral-control designs because it adds eight GPIO lines through an established I2C/SMBus path. The 16-pin SOIC package is straightforward to inspect and rework, and the 2.3 V to 5.5 V supply range supports both legacy 3.3 V and 5 V logic domains. Because the NXP product is no longer manufactured, replacement planning must consider lifecycle, availability, and exact pin compatibility. A qualified substitute should preserve SDA, SCL, address-strapping, reset, interrupt, and port assignments. Production validation should cover startup register state, bus timing, output loading, and any system behavior that depends on interrupt polarity.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para PCA9538D — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | PCA9538DGVR | PCA9538D,112 | PCA9538D,118 | PCA9538D |
|---|---|---|---|---|---|
| Package | SOIC-16 | SOIC-16 | SOIC-16 | SOIC-16 | SOIC-16 |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | Texas Instruments |
| GPIO Count | 8 bits | 8 bits | 8 bits | 8 bits | 8 bits |
| Supply Voltage Range | 2.3 V to 5.5 V | 2.3 V to 5.5 V | 2.3 V to 5.5 V | 2.3 V to 5.5 V | 2.3 V to 5.5 V |
| Maximum I2C Frequency | 400 kHz | 400 kHz | 400 kHz | 400 kHz | 400 kHz |
| Interface | I2C-bus and SMBus | I2C-bus and SMBus | I2C-bus and SMBus | I2C-bus and SMBus | I2C-bus and SMBus |
| Interrupt Output | Yes, active-low INT | Yes, active-low INT | Yes, active-low INT | Yes, active-low INT | Yes |
| Reset Input | Yes, active-low RESET | Yes, active-low RESET | Yes, active-low RESET | Yes, active-low RESET | Yes |
| Hardware Address Inputs | A0 and A1, up to 4 devices | A0 and A1, up to 4 devices | A0 and A1, up to 4 devices | A0 and A1, up to 4 devices | A0 and A1, up to 4 devices |
Diferenciadores clave
- Eight configurable GPIO lines in a conventional SOIC-16 footprint (frente a PCA9538D,112)
- Interrupt and reset support retained for event-driven control (frente a PCA9538D,118)
- Directly identified NXP legacy-device identity (frente a PCA9538D)
Notas de diseño
Place the PCA9538D close to the devices it supports and keep the SDA and SCL routes short, away from switching nodes and high-current traces. Route both bus signals using a continuous ground reference and terminate them with pull-up resistors to the appropriate logic supply. Select the pull-up resistance from the total bus capacitance and required rise time rather than using an arbitrary value. Confirm the A0 and A1 connections before fabrication because incorrect strapping can create an address conflict with another expander.
Treat INT and RESET as system-control signals. The interrupt output is active low, so the receiving host should be configured for the appropriate pull-up, polarity, and edge condition. Keep RESET away from noisy edges and ensure the supply ramp cannot create an unintended reset pulse. If the bus runs near its 400 kHz limit, account for capacitance, pull-up resistance, device input capacitance, and connector or test-point loading. Slow or unequal SCL-to-SDA timing can lead to communication errors even when the nominal bus frequency is correct.
Do not assume that every device described as an eight-bit I/O expander is pin-compatible. Check the exact SOIC-16 footprint, supply range, address pins, reset behavior, interrupt polarity, and register map against the manufacturer datasheet before substitution. PCA9538PW is not a physical drop-in replacement because its TSSOP-16 land pattern differs. For obsolete-product maintenance, record the approved manufacturer, order code, packing method, lot traceability, and firmware qualification results so an alternate source does not silently introduce a behavioral difference.
Información de cumplimiento
The available product information does not provide explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations for this legacy part.