NXP Semiconductors

PCA9538D - 8-Bit I2C GPIO Expander | NXP Semiconductors

部品番号: PCA9538D ✗ 生産終了
2.3 V to 5.5 V Vdss 16 pins Package Up to 400 kHz Speed
MOQ: 1 |

PCA9538D 概要

NXP Semiconductors PCA9538D is an 8-bit CMOS I/O expander for I2C-bus and SMBus systems, operating from 2.3 V to 5.5 V with bus speeds up to 400 kHz. The device adds eight configurable general-purpose parallel input/output lines and is supplied in a 16-pin SOIC package. It also provides an active-low interrupt output, a reset input, and two hardware address pins.

An I/O expander is a peripheral integrated circuit that increases the number of inputs and outputs available to a host controller without requiring a large number of microcontroller pins. In the broader semiconductor hierarchy, the PCA9538D is an I2C interface IC, a GPIO expander, and ultimately a general-purpose semiconductor. It is useful when a system needs more control or status signals than the host microcontroller can expose directly.

The PCA9538 includes an 8-bit configuration register, input port register, output port register, and polarity-inversion register. Each port bit can be configured independently as an input or output. The interrupt output signals a change on a configured input, while the reset input restores the registers to their power-on state. The A0 and A1 address pins allow up to four devices to share one I2C bus.

Its 16-pin CMOS implementation is designed for low-power embedded control. The 2.3 V to 5.5 V operating range covers common 3.3 V and 5 V systems, while the 400 kHz I2C limit supports standard embedded peripheral buses. The SOIC-16 surface-mount package simplifies assembly on conventional through-hole-compatible PCB layouts and provides adequate spacing between pins for hand rework and inspection.

Typical uses include ACPI power-control systems, sensor and switch interfaces, relay or fan controls, LED status and indicator circuits, key scanners, and general-purpose industrial control boards. The interrupt output can reduce polling by notifying the host controller when a monitored input changes, provided the host firmware handles the resulting interrupt and reads the appropriate status register.

PCB design should preserve clear access to SDA, SCL, RESET, INT, and the two address pins. Pull-up resistors are normally required on the open-drain I2C lines and should be selected from the bus capacitance, voltage, and required rise-time calculations. Confirm the A0 and A1 states before multiple expanders share a bus so that each device has a unique address.

This product overview combines the manufacturer functional description with package, interface, register, and application guidance for engineers evaluating the PCA9538D as a legacy embedded-system I/O expansion solution.

ドロップイン代替品: PCA9538D — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。

PCA9538DGVR

✅ ドロップイン
📦 SOIC-16
Ordering-code variant with the same 8-bit I2C GPIO function and 400 kHz bus capability; confirm temperature grade and packing details before substitution

📋 参考代替品(カタログ未掲載)

PCA9538D,112

✅ ドロップイン
📦 SOIC-16
Orderable PCA9538D variant with identical 8-bit GPIO and 2.3 V to 5.5 V core function; exact packing code differs

📋 参考代替品(カタログ未掲載)

PCA9538D,118

✅ ドロップイン
📦 SOIC-16
Orderable PCA9538D packaging variant with the same 8-bit I2C interface, 400 kHz bus rate, interrupt, and reset functions

📋 参考代替品(カタログ未掲載)

PCA9538D

✅ ドロップイン
NXP Semiconductors
📦 SOIC-16
8-bit CMOS I/O expander · 8 · 2.3 V to 5.5 V · Up to 400 kHz · I2C-bus and SMBus · 2.3 V to 5.5 V CMOS · 16 pins · 16-pin SOIC

価格はお問い合わせください

データシートを見る →

PCA9538D 仕様

Device Type 8-bit CMOS I/O expander
Number of I/O Pins 8
Supply Voltage Range 2.3 V to 5.5 V
I2C Bus Speed Up to 400 kHz
Supported Bus I2C-bus and SMBus
Logic Voltage 2.3 V to 5.5 V CMOS
Total Package Pins 16 pins
パッケージ 16-pin SOIC
Configuration Register 8 bits
Input Port Register 8 bits
Output Port Register 8 bits
Polarity Inversion Register 8 bits
Hardware Address Inputs 2 inputs, A0 and A1
Maximum Devices per I2C Bus 4 devices
Interrupt Output Active-low INT output
Reset Input Active-low RESET input
実装タイプ Surface mount

PCA9538D ピン構成

SOIC-16 Package Pinout Diagram SOIC-16 16-pin, 3.9x9.9mm, P1.27mm, JEDEC MS-012. 1 16 2 15 3 14 4 13 5 12 6 11 7 10 8 9 SOIC-16
ピン 1 A0 — Address input A0
ピン 2 A1 — Address input A1
ピン 3 RESET — Active-low reset input
ピン 4 VSS — Ground reference
ピン 5 P0 — General-purpose I/O port 0
ピン 6 P1 — General-purpose I/O port 1
ピン 7 P2 — General-purpose I/O port 2
ピン 8 P3 — General-purpose I/O port 3
ピン 9 P4 — General-purpose I/O port 4
ピン 10 P5 — General-purpose I/O port 5
ピン 11 P6 — General-purpose I/O port 6
ピン 12 P7 — General-purpose I/O port 7
ピン 13 INT — Active-low interrupt output
ピン 14 VDD — Positive supply voltage
ピン 15 SCL — Serial clock input
ピン 16 SDA — Serial data input/output

主な用途

PCA9538D の用途: 6 件s: ACPI Power-Control Interface, Industrial Sensor and Switch Interface, LED Status and Indicator Control, Fan and Relay Control, Embedded Key and Button Scanner, Legacy Motherboard and Peripheral Control.

⚡

ACPI Power-Control Interface

The PCA9538D fits legacy ACPI-compatible control boards where a compact controller must operate several power-related signals. Its eight configurable I/O lines can represent enable, sleep, power-good, or system-state functions, while the 2.3 V to 5.5 V range supports common embedded supply levels. The host communicates through I2C or SMBus at up to 400 kHz, reducing parallel GPIO demand on the system controller. Because the interrupt output can announce input changes, the firmware can react to a power or status event without continuously polling all eight lines. During implementation, assign each signal through the configuration register and confirm active-high or active-low requirements using the polarity-inversion register.

🏭

Industrial Sensor and Switch Interface

The PCA9538D is suitable for collecting digital status from sensors, selectors, limit switches, and operator push buttons in industrial equipment. Each of the eight ports can be configured independently, allowing mixed input and output use on the same expander. With I2C operation up to 400 kHz, the device provides adequate bus bandwidth for low-rate supervisory signals rather than high-frequency sampling. The interrupt output provides event notification when a configured input changes, allowing the controller to service the bus only when needed. Firmware should first read the input register, then determine which state transition caused the interrupt, and finally clear the source as required by the NXP manufacturer datasheet.

💡

LED Status and Indicator Control

The PCA9538D can expand a controller's available outputs for LED status panels, fault indicators, and system-health displays. Its eight independently controlled output lines reduce the number of direct host GPIO pins required for visual status reporting, while the 2.3 V to 5.5 V operating range supports both 3.3 V and 5 V logic systems. The output-port register allows firmware to update multiple indicators through one I2C transaction sequence. When driving LEDs, calculate resistor values from the actual LED forward voltage and supply level, and confirm whether the application requires source or current sinking. The interrupt and reset functions remain useful for coordinated startup and fault-state initialization.

🔧

Fan and Relay Control

The PCA9538D can provide compact control outputs for fans, relays, latches, and other low-rate actuators in embedded equipment. Its eight independently configurable ports allow several actuator commands to share one I2C connection, while the interrupt line can monitor feedback inputs in the same device. The 400 kHz interface is more than sufficient for supervisory commands and status polling, but it is not intended for high-speed pulse generation or precise timing. External driver circuits may still be needed for relay coils, inductive loads, or fan motors. Use appropriate flyback protection, transient suppression, and current limiting, and verify that the port's output limits match the selected load driver.

🖥️

Embedded Key and Button Scanner

The PCA9538D can expand a microcontroller's limited input capacity for keypad rows, panel buttons, and mechanical selectors. Eight configurable inputs reduce wiring to the host and allow the controller to handle several switches without dedicating one GPIO pin to each signal. The interrupt output is particularly useful for low-rate human-interface inputs because the controller can remain idle until a button state changes. Firmware should configure debounce handling in software or external circuitry, account for contact bounce, and use the polarity-inversion register when the board presents active-low button signals. The device's 2.3 V to 5.5 V range supports common control-board logic levels.

🖥️

Legacy Motherboard and Peripheral Control

The PCA9538D remains useful in service and modernization of legacy motherboard and peripheral-control designs because it adds eight GPIO lines through an established I2C/SMBus path. The 16-pin SOIC package is straightforward to inspect and rework, and the 2.3 V to 5.5 V supply range supports both legacy 3.3 V and 5 V logic domains. Because the NXP product is no longer manufactured, replacement planning must consider lifecycle, availability, and exact pin compatibility. A qualified substitute should preserve SDA, SCL, address-strapping, reset, interrupt, and port assignments. Production validation should cover startup register state, bus timing, output loading, and any system behavior that depends on interrupt polarity.

おすすめ製品の概要

PCA9538D NXP Semiconductors 使用用途: ACPI Power-Control Interface, Industrial Sensor and Switch Interface, LED Status and Indicator Control, Fan and Relay Control, Embedded Key and Button Scanner, Legacy Motherboard and Peripheral Control PCA9538DGVR Orderable NXP family variant for supply assessment 使用用途: ACPI Power-Control Interface, LED Status and Indicator Control PCA9538D,112 NXP orderable family option 使用用途: Industrial Sensor and Switch Interface, Embedded Key and Button Scanner PCA9538D,118 NXP orderable PCA9538 family variant 使用用途: Fan and Relay Control, Legacy Motherboard and Peripheral Control
What does the PCA9538D do?
The PCA9538D adds eight configurable GPIO lines to a host controller through an I2C-bus or SMBus interface. According to the NXP manufacturer datasheet, each of the eight lines can be selected as an input or output through the configuration register. The device also includes input, output, and polarity-inversion registers, an interrupt output, and a reset input, making it suitable for adding switches, sensors, indicators, or control signals without consuming additional microcontroller GPIO pins.
What is the operating voltage of PCA9538D?
The PCA9538D operates from 2.3 V to 5.5 V, allowing it to work with common 3.3 V and 5 V embedded systems. The NXP manufacturer datasheet identifies the device as a low-power CMOS I/O port supporting I2C-bus and SMBus communication. The host controller and expander should use compatible logic levels, and pull-up resistors on SDA and SCL must be referenced to the same supply voltage used by the bus devices.
Where can I download the PCA9538D datasheet PDF?
The official PCA9538D datasheet PDF is available from NXP at https://www.nxp.com/docs/en/data-sheet/PCA9538.pdf. It documents the configuration, input, output, and polarity-inversion registers, along with electrical characteristics and the 16-pin pinout. The NXP product page at https://www.nxp.com/part/PCA9538D provides lifecycle information and links to the manufacturer data sheet. Use the NXP document for board design and firmware decisions because it defines the authoritative register behavior.
Where can I find the PCA9538D pinout?
The PCA9538D pinout is shown in the pin-description table and package drawing of the NXP manufacturer datasheet. The 16-pin SOIC connects A0, A1, RESET, SCL, SDA, INT, VCC, VSS, and P0 through P7. When assigning PCB tracks, use the numbered pins from the datasheet drawing and preserve access to the address, reset, and interrupt functions. Incorrect SDA or SCL placement can prevent assembly or make the bus difficult to debug.
How many PCA9538D devices can share one I2C bus?
Up to four PCA9538D devices can share one I2C bus because the A0 and A1 address pins provide four hardware-selectable addresses. According to the NXP manufacturer datasheet, each combination of A0 and A1 produces a distinct device address. Firmware should use the resulting address to identify the correct expander. If more than four expanders are required, a second I2C bus or another bus multiplexer is needed, subject to the capabilities of the host controller.
What is the PCA9538D I2C bus speed?
The PCA9538D supports I2C-bus operation up to 400 kHz, also known as Fast-mode I2C. The NXP manufacturer datasheet identifies the part as an I2C-bus and SMBus low-power I/O port, and distributor product records identify a maximum bus frequency of 400 kHz. The complete bus must remain within this limit, including the effects of pull-up resistance, total bus capacitance, wiring length, and the rise time required by the host and peripheral.
What is the difference between PCA9538D and PCA9538PW?
The principal documented distinction is the physical package: PCA9538D uses a 16-pin SOIC, while PCA9538PW is offered in a 16-pin TSSOP. Their core function is the same eight-bit I2C or SMBus GPIO expansion with interrupt and reset, but a TSSOP has finer lead spacing and requires a different PCB land pattern. PCA9538PW therefore cannot replace PCA9538D on an unchanged board even though the logical device functions are closely related.
Is the Texas Instruments PCA9538D a drop-in replacement for the NXP PCA9538D?
The Texas Instruments PCA9538D is a close functional and package-oriented alternative for an eight-bit I2C GPIO expander, but firmware and board validation are still required before treating it as a drop-in replacement. The NXP and TI devices implement the same core I2C I/O-expander function with interrupt, reset, and configuration registers. Confirm the exact SOIC-16 pin assignments, register behavior, electrical limits, and address map against the applicable manufacturer datasheets for the specific production build.
When should I choose PCA9538D instead of an MCU with more GPIO pins?
Choose PCA9538D when the host already communicates over I2C and adding eight slow GPIO lines is preferable to selecting a larger microcontroller. Its dedicated interrupt output can also reduce routine input polling. The trade-off is that external port access requires serial transactions and firmware handling, whereas directly integrated MCU GPIO is generally faster and simpler. PCA9538D is most appropriate for legacy boards, control signals, indicators, and low-rate input sensing rather than high-speed waveforms.
Is PCA9538D suitable for sensor and switch inputs?
Yes, the PCA9538D is suitable for digital sensors, push buttons, selectors, and other low-speed switch inputs because it provides eight independently configurable GPIO lines. The NXP manufacturer datasheet identifies sensor, push-button, LED, and fan interfaces as representative uses. Configure each required line as an input and use the polarity-inversion register when the external signal is active-low. The interrupt output can notify the host of a change, reducing the need for continuous register polling.
How does the PCA9538D reset function work?
The PCA9538D reset function restores the device registers to their power-on default state when the active-low RESET input is asserted. According to the NXP manufacturer datasheet, the configuration, input, output, and polarity-inversion registers are reset along with the interrupt mechanism. A system can also obtain the default state by cycling the supply. External reset circuitry should avoid false pulses during power sequencing, and the RESET trace should be kept away from noisy switching nodes.
What can replace PCA9538D?
The closest documented replacement candidates are orderable NXP PCA9538 device variants and the Texas Instruments PCA9538D, but each must be checked for package, pinout, electrical limits, register behavior, and supply availability. PCA9538PW is only a functional alternative because its TSSOP-16 land pattern differs from the PCA9538D's SOIC-16 footprint. For a no-PCB-change replacement, verify the candidate's SOIC-16 pin arrangement and interrupt polarity rather than relying on the device description alone.
Is PCA9538D the same as PCA9538DGVR?
PCA9538DGVR is an NXP orderable variant of the PCA9538 family, while PCA9538D identifies the base device designation used for the 16-pin SOIC version. They should not be treated as electrically different merely because the ordering codes differ. Confirm the package, temperature range, packing format, and marking in the current NXP ordering information. For PCB interchangeability, the most important requirement is that every pin performs the same function in the same SOIC-16 position.
Is PCA9538D currently manufactured?
No, NXP identifies PCA9538D as no longer manufactured on its official product page. It should therefore be treated as an obsolete or legacy supply item rather than a new-design standard. For ongoing production, request current availability and lifecycle options through the Request a Quote form on this page. A migration should use an explicitly qualified pin-compatible device and include firmware, electrical, and environmental validation instead of assuming that similar GPIO-expander functions are interchangeable.
What are the key specifications of PCA9538D that engineers should know?
The key PCA9538D specifications are eight independently configurable GPIO lines, a 2.3 V to 5.5 V operating range, I2C/SMBus communication up to 400 kHz, four selectable addresses, and a 16-pin SOIC package. The NXP manufacturer datasheet also documents separate configuration, input, output, and polarity-inversion registers, plus interrupt and reset functions. These characteristics place the device in low-speed embedded GPIO expansion rather than high-speed or high-voltage I/O categories.

エンジニアリング参考データ: PCA9538D — 比較、設計ガイダンス、コンプライアンス情報。

選定ガイド

Choose the NXP PCA9538D when maintaining a legacy design that specifically calls for its established eight-bit I2C GPIO-expander behavior, SOIC-16 footprint, interrupt polarity, and register implementation. The NXP orderable family variants can help with supply continuity, but confirm the exact order code, temperature grade, packing method, and lifecycle status before releasing production quantities. Consider the Texas Instruments PCA9538D only after comparing the pinout, electrical limits, reset behavior, interrupt output, address map, and register semantics in the manufacturer datasheets. Do not select PCA9538PW for an unchanged PCA9538D board because its TSSOP-16 land pattern requires PCB changes. For new designs, evaluate whether direct MCU GPIO or a current, non-obsolete expander provides better lifecycle support. No substitute should be approved solely from bus frequency and GPIO count; startup state, address strapping, reset behavior, and interrupt handling are equally important.

代替品との比較

パラメータ この製品 PCA9538DGVR PCA9538D,112 PCA9538D,118 PCA9538D
Package SOIC-16 SOIC-16 SOIC-16 SOIC-16 SOIC-16
Brand NXP Semiconductors NXP Semiconductors NXP Semiconductors NXP Semiconductors Texas Instruments
GPIO Count 8 bits 8 bits 8 bits 8 bits 8 bits
Supply Voltage Range 2.3 V to 5.5 V 2.3 V to 5.5 V 2.3 V to 5.5 V 2.3 V to 5.5 V 2.3 V to 5.5 V
Maximum I2C Frequency 400 kHz 400 kHz 400 kHz 400 kHz 400 kHz
Interface I2C-bus and SMBus I2C-bus and SMBus I2C-bus and SMBus I2C-bus and SMBus I2C-bus and SMBus
Interrupt Output Yes, active-low INT Yes, active-low INT Yes, active-low INT Yes, active-low INT Yes
Reset Input Yes, active-low RESET Yes, active-low RESET Yes, active-low RESET Yes, active-low RESET Yes
Hardware Address Inputs A0 and A1, up to 4 devices A0 and A1, up to 4 devices A0 and A1, up to 4 devices A0 and A1, up to 4 devices A0 and A1, up to 4 devices

主な差別化要因

  • Eight configurable GPIO lines in a conventional SOIC-16 footprint (vs PCA9538D,112)
  • Interrupt and reset support retained for event-driven control (vs PCA9538D,118)
  • Directly identified NXP legacy-device identity (vs PCA9538D)

設計ノート

Place the PCA9538D close to the devices it supports and keep the SDA and SCL routes short, away from switching nodes and high-current traces. Route both bus signals using a continuous ground reference and terminate them with pull-up resistors to the appropriate logic supply. Select the pull-up resistance from the total bus capacitance and required rise time rather than using an arbitrary value. Confirm the A0 and A1 connections before fabrication because incorrect strapping can create an address conflict with another expander.

Treat INT and RESET as system-control signals. The interrupt output is active low, so the receiving host should be configured for the appropriate pull-up, polarity, and edge condition. Keep RESET away from noisy edges and ensure the supply ramp cannot create an unintended reset pulse. If the bus runs near its 400 kHz limit, account for capacitance, pull-up resistance, device input capacitance, and connector or test-point loading. Slow or unequal SCL-to-SDA timing can lead to communication errors even when the nominal bus frequency is correct.

Do not assume that every device described as an eight-bit I/O expander is pin-compatible. Check the exact SOIC-16 footprint, supply range, address pins, reset behavior, interrupt polarity, and register map against the manufacturer datasheet before substitution. PCA9538PW is not a physical drop-in replacement because its TSSOP-16 land pattern differs. For obsolete-product maintenance, record the approved manufacturer, order code, packing method, lot traceability, and firmware qualification results so an alternate source does not silently introduce a behavioral difference.

コンプライアンス情報

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
鉛フリー
Unknown
ハロゲンフリー
Unknown
紛争鉱物
Unknown

The available product information does not provide explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations for this legacy part.

関連検索

pca9538 datasheet PCA9538D datasheet PDF PCA9538D pinout PCA9538D equivalent PCA9538D replacement PCA9538D vs PCA9538PW PCA9538D SOIC-16 GPIO expander PCA9538D 400 kHz I2C PCA9538D 2.3V 5.5V PCA9538D GPIO application circuit PCA9538D price PCA9538D stock

関連部品&用語

NXP Semiconductors PCA9538D PCA9538DGVR PCA9538D,112 PCA9538D,118 Texas Instruments PCA9538 PCA9538PW I/O expander GPIO expander parallel I/O I2C-bus SMBus interface IC CMOS semiconductor SOIC-16 SOIC package surface-mount package interrupt output reset input polarity inversion address input ACPI
クイック見積RFQ
詳細をすべてご記入ください — 営業チームが24時間以内にご返信いたします
部品番号 メーカー パッケージ QTY 目標価格 小計
✓
見積を送信しました!

24時間以内にメールでご返信いたします

1
RFQ送信済み
2
見積受領
3
注文済み
4
お支払い
5
発送済み
6
配達済み
RFQの詳細を表示