PCF8575PWG4 - 16-Bit I2C I/O Expander | Texas Instruments
N.º de pieza: PCF8575PWG4 ✓ ActivoPCF8575PWG4 Descripción general
An I/O expander is an interface IC that increases the number of general-purpose digital lines available to a microcontroller or other bus master. The PCF8575 belongs to the I/O expander category within interface ICs and translates parallel I/O operations into I2C or SMBus transactions. Its 16 ports can each operate as an input or output, with no separate data-direction register required.
Key features include three hardware address inputs, eight programmable I/O ports on each side of the device, and power-on initialization with all I/O lines high. The quasi-bidirectional architecture uses a weak pull-up arrangement that allows an external circuit to override an output-low state. The open-drain interrupt output can be wired as active-low and provides a shared indication when an input changes state.
The PCF8575 core supports operation across a 2.5 V to 5.5 V supply range, making it suitable for both 3.3 V and 5 V systems. Its I2C interface operates up to 400 kHz, while the three address pins permit multiple expanders to share a bus. Because each port combines input detection and output drive, the device is particularly useful for reading switch states, reading logic-level sensors, controlling discrete loads, and driving LED indicators within defined current limits.
Typical applications include industrial control boards, automated test equipment, display and keypad interfaces, LED status panels, and small embedded systems where a microcontroller has insufficient port pins. The open-drain interrupt output is especially useful in battery-operated or duty-cycled systems because the host can remain idle until an input event requires attention. The interrupt pin remains open-drain, allowing multiple expanders to share a common interrupt line when the system uses separate address selections.
For PCB design, place the device close to the connector or sensor wiring that it serves and route the SCL and SDA traces away from high-current switching nodes. Pull-ups must be sized for the bus voltage and capacitance, while the interrupt net requires appropriate pull-up treatment because its output is open-drain. Confirm every external driver against the port sink-current and voltage limits in the manufacturer datasheet.
This page combines the manufacturer electrical characteristics, package information, drop-in device comparison, interface design guidance, and application-specific implementation guidance for engineers designing around the PCF8575PWG4.
Alternativas directas para PCF8575PWG4 — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con PCF8575PWG4 (mismo factor de forma y huella) — difiere en Interrupt Output, Package, Output Drive Capability, Interface Type, Device Type.
PCF8575PWR
✅ Sustitución directaConsulte el precio
Ver hoja de datos →PCF8575PWE4
✅ Sustitución directaConsulte el precio
Ver hoja de datos →PCF8575PW
✅ Sustitución directaConsulte el precio
Ver hoja de datos →PCF8575CPW
✅ Sustitución directaConsulte el precio
Ver hoja de datos →PCF8575PWG4 Especificaciones
| Device Type | 16-bit I2C and SMBus I/O expander with interrupt |
| Number of I/O Ports | 16 |
| Port Organization | 2 ports of 8 I/O lines |
| Supply Voltage Range | 2.5 V to 5.5 V |
| I2C Maximum Clock Frequency | 400 kHz |
| Tipo de interfaz | I2C and SMBus |
| Interrupt Output | Open-drain active-low |
| Address Configuration | 3 hardware address inputs |
| Power-On Port State | All I/O lines high |
| I/O Architecture | Quasi-bidirectional input/output |
| Standby Current | 10 uA maximum |
| Encapsulado | 24-TSSOP, 4.40 mm body width |
| Number of Terminals | 24 |
| Tipo de montaje | Surface mount |
| Temperature Grade | Industrial |
| Lead-Free / Green | Yes |
Configuración de pines de PCF8575PWG4
| Pin 1 | P00 — Quasi-bidirectional I/O port 0 |
| Pin 2 | P01 — Quasi-bidirectional I/O port 1 |
| Pin 3 | P02 — Quasi-bidirectional I/O port 2 |
| Pin 4 | P03 — Quasi-bidirectional I/O port 3 |
| Pin 5 | P04 — Quasi-bidirectional I/O port 4 |
| Pin 6 | P05 — Quasi-bidirectional I/O port 5 |
| Pin 7 | P06 — Quasi-bidirectional I/O port 6 |
| Pin 8 | P07 — Quasi-bidirectional I/O port 7 |
| Pin 9 | INT — Active-low open-drain interrupt output |
| Pin 10 | VSS — Ground reference |
| Pin 11 | SCL — Serial clock input |
| Pin 12 | SDA — Bidirectional serial data input and output |
| Pin 13 | A0 — Hardware address input 0 |
| Pin 14 | A1 — Hardware address input 1 |
| Pin 15 | A2 — Hardware address input 2 |
| Pin 16 | P10 — Quasi-bidirectional I/O port 10 |
| Pin 17 | P11 — Quasi-bidirectional I/O port 11 |
| Pin 18 | P12 — Quasi-bidirectional I/O port 12 |
| Pin 19 | P13 — Quasi-bidirectional I/O port 13 |
| Pin 20 | P14 — Quasi-bidirectional I/O port 14 |
| Pin 21 | P15 — Quasi-bidirectional I/O port 15 |
| Pin 22 | VCC — Power supply input |
| Pin 23 | NC — Not connected |
| Pin 24 | NC — Not connected |
Aplicaciones típicas
PCF8575PWG4 es adecuado para 6 aplicacións: Industrial Control and Relay Inputs, LED Status and Indicator Panel, Keypad and Switch Matrix Interface, Automated Test Equipment Interface, Battery-Powered Embedded Control, Home and Building Automation Node.
Industrial Control and Relay Inputs
The PCF8575PWG4 is appropriate for industrial controller boards that need to read multiple discrete inputs without consuming the host microcontroller's limited GPIO pins. Its 16 quasi-bidirectional ports can monitor switches, contactors, or logic-level sensors while the 2.5 V to 5.5 V supply range supports both 3.3 V and 5 V control systems. The 400 kHz I2C interface reduces serial traffic during input polling. For changing inputs, the open-drain interrupt output allows the controller to wake or update only after an event. Engineers should confirm input thresholds and port drive limits in the manufacturer datasheet, account for industrial noise filtering, and use appropriate pull-up resistors on both the bus and interrupt nets.
Recomendado
LED Status and Indicator Panel
The PCF8575PWG4 can reduce the I/O burden of a microcontroller in an LED status panel by controlling up to 16 indicator outputs over I2C. Because each port is latched and quasi-bidirectional, the controller can update several indicators in one serial transaction, reducing pin usage and simplifying the PCB layout. The device operates at 3.3 V or 5 V and supports 400 kHz bus communication for quick panel updates. Design the LED paths so that the total per-pin and aggregate device loading remain within the published limits. If an indicator needs constant current above those limits, use an external driver transistor or LED driver rather than overloading the expander.
Recomendado
Keypad and Switch Matrix Interface
The PCF8575PWG4 is well suited to small keypads, selector switches, and configuration panels where a host controller lacks sufficient direct inputs. Sixteen quasi-bidirectional lines provide flexible input and output use without a separate direction register, while three address inputs allow multiple expanders to share an I2C bus. The open-drain interrupt can signal a changed input, helping the controller avoid continuous polling during low-power operation. At a 400 kHz bus rate, scan and update latency can be kept short for responsive user interfaces. Validate logic thresholds, debounce strategy, and port drive capability, and ensure pull-ups are suitable for the actual bus capacitance and voltage.
Recomendado
Automated Test Equipment Interface
The PCF8575PWG4 can serve as a compact parallel-interface bridge in automated test equipment, connecting a controller to limit sensors, fixture controls, and status lamps. Its 16 I/O lines reduce the number of host-controller pins needed for fixture I/O, while the I2C interface keeps the PCB wiring compact and organized. A 2.5 V to 5.5 V supply range supports legacy 5 V fixtures and modern 3.3 V controller boards, subject to interface-level compatibility. The open-drain interrupt output is useful for prompting the test sequencer to check changed fixture conditions. For high-speed or high-current loads, add suitable external drivers and preserve the device's published voltage and current limits.
Recomendado
Battery-Powered Embedded Control
The PCF8575PWG4 is useful in battery-powered embedded systems that need a small number of control and status lines without allocating many MCU pins. Its 10 uA maximum standby current and wide 2.5 V to 5.5 V operating range support low-voltage designs, while the interrupt output enables event-driven operation instead of continuous I2C polling. The 16 ports can monitor wake-capable switches or operate low-current status indicators. Power management still depends on the complete system design, including pull-up resistance, bus activity, and attached loads. Use the lowest practical bus voltage, account for resistor leakage, and verify that every external line remains within the PCF8575's absolute-maximum limits during sleep and wake transitions.
Recomendado
Home and Building Automation Node
The PCF8575PWG4 can expand a compact home-automation or building-automation controller with inputs for door, presence, and configuration switches and outputs for low-current indicators or control signals. Three address inputs allow multiple PCF8575 devices to coexist on the same I2C bus when more than 16 lines are needed. Its 2.5 V minimum supply supports low-energy nodes, and the open-drain interrupt provides an efficient way to notify the controller of an input change. A common interrupt line can be shared by appropriately addressed devices. Design the enclosure, wiring protection, and ESD strategy separately from the logic circuit, and verify that externally connected cable transients cannot exceed the port ratings.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para PCF8575PWG4 — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | PCF8575PWR | PCF8575PWE4 | PCF8575PW | PCF8575CPW |
|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 24-TSSOP | 24-TSSOP | 24-TSSOP | 24-TSSOP | 24-TSSOP |
| I/O Port Count | 16 | 16 | 16 | 16 | 16 |
| Supply Voltage Range | 2.5 V to 5.5 V | 2.5 V to 5.5 V | 2.5 V to 5.5 V | 2.5 V to 5.5 V | 4.5 V to 5.5 V |
| Maximum I2C Clock Frequency | 400 kHz | 400 kHz | 400 kHz | 400 kHz | 400 kHz |
| Address Inputs | 3 | 3 | 3 | 3 | 3 |
| Interrupt Output | Open-drain active-low | Open-drain active-low | Open-drain active-low | Open-drain active-low | Open-drain active-low |
| I/O Architecture | Quasi-bidirectional | Quasi-bidirectional | Quasi-bidirectional | Quasi-bidirectional | Quasi-bidirectional |
Diferenciadores clave
- Wider low-voltage supply support than the PCF8575CPW (frente a PCF8575CPW)
- Sixteen integrated quasi-bidirectional I/O lines (frente a PCF8575CPW)
- Event-driven system operation through the interrupt output (frente a PCF8575PWR)
Notas de diseño
Place the PCF8575PWG4 near the connector, switch bank, or indicator circuitry it serves to minimize trace length and improve signal integrity. Route SCL and SDA away from relay coils, switching-regulator inductors, and high-current LED return paths. Keep the I2C traces short and continuous, use a common ground reference, and place the required bus pull-ups near the master or according to the system-level bus topology.
Size the SDA and SCL pull-ups for the actual bus voltage, total capacitance, and sink-current capability of every connected device. The interrupt output is also open-drain and requires a pull-up. Avoid selecting unnecessarily weak pull-ups that produce slow rising edges at 400 kHz, or excessively strong pull-ups that overload the bus. Validate the complete network with an oscilloscope across the intended cable length and operating conditions.
Do not treat the quasi-bidirectional ports as ordinary push-pull GPIO outputs. A quasi-bidirectional output has a pull-up structure that can be overridden by another driver, so external circuits must respect the port current and voltage limits. Confirm whether a load requires a low output, a high output, or an input with an external pull-up. Use the manufacturer datasheet's absolute-maximum ratings to evaluate startup, disconnected-cable, and fault conditions.
Configure the three address inputs before power-on and avoid leaving their nets floating. Each device on a shared bus must have a unique address combination. Because the interrupt output is open-drain, several expanders may share one interrupt line, but the host must identify the changed device by reading the appropriate bus address. Preserve clear pin-1 orientation and follow the 24-TSSOP land pattern in the manufacturer package drawing.
Información de cumplimiento
The industrial-grade PCF8575PWG4 is identified as a green, lead-free order option. RoHS, REACH, halogen-free, conflict-minerals, and automotive qualification statements require confirmation from the current manufacturer product documentation.