Texas Instruments

PCF8575PWG4 - 16-Bit I2C I/O Expander | Texas Instruments

N.º da peça: PCF8575PWG4 ✓ Ativo
2.5 V to 5.5 V Vdss 10 uA maximum Id 24-TSSOP, 4.40 mm body width Package 400 kHz Speed
MOQ: 1 |

PCF8575PWG4 Visão geral

Texas Instruments PCF8575PWG4 is a 16-bit I2C and SMBus I/O expander with an interrupt output, operating from 2.5 V to 5.5 V and supporting I2C speeds up to 400 kHz. The device provides 16 quasi-bidirectional I/O lines in a 24-pin TSSOP package, allowing a host microcontroller to monitor inputs and control outputs over a two-wire serial bus. Its open-drain interrupt output supports efficient change notification without continuous polling.

An I/O expander is an interface IC that increases the number of general-purpose digital lines available to a microcontroller or other bus master. The PCF8575 belongs to the I/O expander category within interface ICs and translates parallel I/O operations into I2C or SMBus transactions. Its 16 ports can each operate as an input or output, with no separate data-direction register required.

Key features include three hardware address inputs, eight programmable I/O ports on each side of the device, and power-on initialization with all I/O lines high. The quasi-bidirectional architecture uses a weak pull-up arrangement that allows an external circuit to override an output-low state. The open-drain interrupt output can be wired as active-low and provides a shared indication when an input changes state.

The PCF8575 core supports operation across a 2.5 V to 5.5 V supply range, making it suitable for both 3.3 V and 5 V systems. Its I2C interface operates up to 400 kHz, while the three address pins permit multiple expanders to share a bus. Because each port combines input detection and output drive, the device is particularly useful for reading switch states, reading logic-level sensors, controlling discrete loads, and driving LED indicators within defined current limits.

Typical applications include industrial control boards, automated test equipment, display and keypad interfaces, LED status panels, and small embedded systems where a microcontroller has insufficient port pins. The open-drain interrupt output is especially useful in battery-operated or duty-cycled systems because the host can remain idle until an input event requires attention. The interrupt pin remains open-drain, allowing multiple expanders to share a common interrupt line when the system uses separate address selections.

For PCB design, place the device close to the connector or sensor wiring that it serves and route the SCL and SDA traces away from high-current switching nodes. Pull-ups must be sized for the bus voltage and capacitance, while the interrupt net requires appropriate pull-up treatment because its output is open-drain. Confirm every external driver against the port sink-current and voltage limits in the manufacturer datasheet.

This page combines the manufacturer electrical characteristics, package information, drop-in device comparison, interface design guidance, and application-specific implementation guidance for engineers designing around the PCF8575PWG4.

Alternativas drop-in para PCF8575PWG4 — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.

Variantes desta série

Modelos da mesma série compatíveis como drop-in com PCF8575PWG4 (mesmo formato e footprint) — diferindo em Interrupt Output, Package, Output Drive Capability, Interface Type, Device Type.

Texas Instruments
Interrupt Output: Yes
Package: 24-pin TSSOP (PW)
Output Drive Capability: High-current drive for direct LED driving
Comparar com PCF8575PWG4 →
Texas Instruments
Interrupt Output: Open-drain
Package: 24-pin TSSOP (PW)
Output Drive Capability: High-current LED drive capability
Comparar com PCF8575PWG4 →
Texas Instruments
Interrupt Output: Open-drain
Package: 24-pin TSSOP
Output Drive Capability: High-current drive for directly driving LEDs
Comparar com PCF8575PWG4 →

PCF8575PWR

✅ Drop-In
Texas Instruments
📦 24-TSSOP
16 · 2 x 8-bit · 2.5 V to 5.5 V · 400 kHz · I2C and SMBus · Open-drain · 3 · 8 devices

Consulte o preço

Ver ficha técnica →

PCF8575PWE4

✅ Drop-In
Texas Instruments
📦 24-TSSOP
16 lines · 2 ports of 8 I/O lines · 2.5 V to 5.5 V · 3.3 V · 400 kHz maximum · I2C and SMBus · Open-drain · 10 uA maximum

Consulte o preço

Ver ficha técnica →

PCF8575PW

✅ Drop-In
Texas Instruments
📦 24-TSSOP
16 ports · 2.5 V to 5.5 V · I2C/SMBus, 2-wire serial · 400 kHz · 3 inputs, supporting up to 8 devices · Open-drain · 10 µA · 16 individually latched ports

Consulte o preço

Ver ficha técnica →

PCF8575CPW

✅ Drop-In
Texas Instruments
📦 24-TSSOP
16-bit I2C/SMBus I/O expander with interrupt · 16 lines · 4.5 V to 5.5 V · 400 kHz · I2C/SMBus · Yes · 16-bit quasi-bidirectional port · High-current drive for direct LED driving

Consulte o preço

Ver ficha técnica →

PCF8575PWG4 Especificações

Device Type 16-bit I2C and SMBus I/O expander with interrupt
Number of I/O Ports 16
Port Organization 2 ports of 8 I/O lines
Supply Voltage Range 2.5 V to 5.5 V
I2C Maximum Clock Frequency 400 kHz
Tipo de interface I2C and SMBus
Interrupt Output Open-drain active-low
Address Configuration 3 hardware address inputs
Power-On Port State All I/O lines high
I/O Architecture Quasi-bidirectional input/output
Standby Current 10 uA maximum
Encapsulamento 24-TSSOP, 4.40 mm body width
Number of Terminals 24
Tipo de montagem Surface mount
Temperature Grade Industrial
Lead-Free / Green Yes

Configuração de pinos do PCF8575PWG4

TSSOP-24 Package Pinout Diagram TSSOP-24 4.4x7.8mm, P0.65mm, JEDEC MO-153. 1 24 2 23 3 22 4 21 5 20 6 19 7 18 8 17 9 16 10 15 11 14 12 13 TSSOP-24
Pino 1 P00 — Quasi-bidirectional I/O port 0
Pino 2 P01 — Quasi-bidirectional I/O port 1
Pino 3 P02 — Quasi-bidirectional I/O port 2
Pino 4 P03 — Quasi-bidirectional I/O port 3
Pino 5 P04 — Quasi-bidirectional I/O port 4
Pino 6 P05 — Quasi-bidirectional I/O port 5
Pino 7 P06 — Quasi-bidirectional I/O port 6
Pino 8 P07 — Quasi-bidirectional I/O port 7
Pino 9 INT — Active-low open-drain interrupt output
Pino 10 VSS — Ground reference
Pino 11 SCL — Serial clock input
Pino 12 SDA — Bidirectional serial data input and output
Pino 13 A0 — Hardware address input 0
Pino 14 A1 — Hardware address input 1
Pino 15 A2 — Hardware address input 2
Pino 16 P10 — Quasi-bidirectional I/O port 10
Pino 17 P11 — Quasi-bidirectional I/O port 11
Pino 18 P12 — Quasi-bidirectional I/O port 12
Pino 19 P13 — Quasi-bidirectional I/O port 13
Pino 20 P14 — Quasi-bidirectional I/O port 14
Pino 21 P15 — Quasi-bidirectional I/O port 15
Pino 22 VCC — Power supply input
Pino 23 NC — Not connected
Pino 24 NC — Not connected

Aplicações típicas

PCF8575PWG4 é adequado para 6 aplicaçãos: Industrial Control and Relay Inputs, LED Status and Indicator Panel, Keypad and Switch Matrix Interface, Automated Test Equipment Interface, Battery-Powered Embedded Control, Home and Building Automation Node.

🏭

Industrial Control and Relay Inputs

The PCF8575PWG4 is appropriate for industrial controller boards that need to read multiple discrete inputs without consuming the host microcontroller's limited GPIO pins. Its 16 quasi-bidirectional ports can monitor switches, contactors, or logic-level sensors while the 2.5 V to 5.5 V supply range supports both 3.3 V and 5 V control systems. The 400 kHz I2C interface reduces serial traffic during input polling. For changing inputs, the open-drain interrupt output allows the controller to wake or update only after an event. Engineers should confirm input thresholds and port drive limits in the manufacturer datasheet, account for industrial noise filtering, and use appropriate pull-up resistors on both the bus and interrupt nets.

💡

LED Status and Indicator Panel

The PCF8575PWG4 can reduce the I/O burden of a microcontroller in an LED status panel by controlling up to 16 indicator outputs over I2C. Because each port is latched and quasi-bidirectional, the controller can update several indicators in one serial transaction, reducing pin usage and simplifying the PCB layout. The device operates at 3.3 V or 5 V and supports 400 kHz bus communication for quick panel updates. Design the LED paths so that the total per-pin and aggregate device loading remain within the published limits. If an indicator needs constant current above those limits, use an external driver transistor or LED driver rather than overloading the expander.

🔧

Keypad and Switch Matrix Interface

The PCF8575PWG4 is well suited to small keypads, selector switches, and configuration panels where a host controller lacks sufficient direct inputs. Sixteen quasi-bidirectional lines provide flexible input and output use without a separate direction register, while three address inputs allow multiple expanders to share an I2C bus. The open-drain interrupt can signal a changed input, helping the controller avoid continuous polling during low-power operation. At a 400 kHz bus rate, scan and update latency can be kept short for responsive user interfaces. Validate logic thresholds, debounce strategy, and port drive capability, and ensure pull-ups are suitable for the actual bus capacitance and voltage.

🖥️

Automated Test Equipment Interface

The PCF8575PWG4 can serve as a compact parallel-interface bridge in automated test equipment, connecting a controller to limit sensors, fixture controls, and status lamps. Its 16 I/O lines reduce the number of host-controller pins needed for fixture I/O, while the I2C interface keeps the PCB wiring compact and organized. A 2.5 V to 5.5 V supply range supports legacy 5 V fixtures and modern 3.3 V controller boards, subject to interface-level compatibility. The open-drain interrupt output is useful for prompting the test sequencer to check changed fixture conditions. For high-speed or high-current loads, add suitable external drivers and preserve the device's published voltage and current limits.

🔋

Battery-Powered Embedded Control

The PCF8575PWG4 is useful in battery-powered embedded systems that need a small number of control and status lines without allocating many MCU pins. Its 10 uA maximum standby current and wide 2.5 V to 5.5 V operating range support low-voltage designs, while the interrupt output enables event-driven operation instead of continuous I2C polling. The 16 ports can monitor wake-capable switches or operate low-current status indicators. Power management still depends on the complete system design, including pull-up resistance, bus activity, and attached loads. Use the lowest practical bus voltage, account for resistor leakage, and verify that every external line remains within the PCF8575's absolute-maximum limits during sleep and wake transitions.

🧩

Home and Building Automation Node

The PCF8575PWG4 can expand a compact home-automation or building-automation controller with inputs for door, presence, and configuration switches and outputs for low-current indicators or control signals. Three address inputs allow multiple PCF8575 devices to coexist on the same I2C bus when more than 16 lines are needed. Its 2.5 V minimum supply supports low-energy nodes, and the open-drain interrupt provides an efficient way to notify the controller of an input change. A common interrupt line can be shared by appropriately addressed devices. Design the enclosure, wiring protection, and ESD strategy separately from the logic circuit, and verify that externally connected cable transients cannot exceed the port ratings.

What is the PCF8575PWG4 and what does it do?
The PCF8575PWG4 is a 16-bit I2C and SMBus I/O expander that adds 16 quasi-bidirectional digital lines to a host controller. It operates from 2.5 V to 5.5 V, supports bus speeds up to 400 kHz, and provides an open-drain interrupt output. According to the Texas Instruments PCF8575 datasheet, each port can be used as an input or output, and all I/O lines initialize high at power-on.
Where can I download the PCF8575PWG4 datasheet PDF?
The official PCF8575PWG4 datasheet PDF is available from the Texas Instruments product page at https://www.ti.com/lit/ds/symlink/pcf8575.pdf. It contains the electrical characteristics, 24-pin connection information, operating principles, and application details. Use the pin-configuration table and package drawings in that document when assigning PCB nets and checking footprint dimensions.
Where can I find the PCF8575PWG4 pinout?
The PCF8575PWG4 pinout is shown in the Texas Instruments PCF8575 datasheet under the pin configuration section. The 24-pin TSSOP provides P00 through P07, an active-low open-drain interrupt, ground, SCL, SDA, three address inputs, P10 through P15, and supply connections. Use the manufacturer pin table when assigning nets because unused positions must remain electrically correct.
Where can I buy PCF8575PWG4 online?
Use the Request a Quote form on this XAIPART product page to request availability, current lead time, and order details for PCF8575PWG4. The form is the appropriate route for a quote-first electronic component without relying on changing distributor inventory. Confirm the exact PCF8575PWG4 suffix and industrial temperature grade when submitting the request.
What is the price of PCF8575PWG4?
The current commercial price for PCF8575PWG4 should be obtained through the Request a Quote form on this page. Electronic component pricing can change with inventory, order quantity, and market conditions, so a current quote is more reliable than a static historical figure. Include the desired quantity, packaging preference, and target delivery location in the request.
What is the lead time and stock status of PCF8575PWG4?
Current stock and lead-time confirmation for PCF8575PWG4 should be requested through the Request a Quote form on this page. The component is a cataloged Texas Instruments I/O expander, but production availability can vary by package suffix and quantity. Supply the required quantity and project schedule so procurement can confirm the appropriate allocation and delivery plan.
Is PCF8575PWG4 in stock?
Inventory status for PCF8575PWG4 is confirmed through the Request a Quote form on this page rather than through a static listing. When requesting stock, specify whether the part is required in the original 24-pin TSSOP configuration and the quantity needed for your production build. This helps procurement distinguish exact-suffix demand from requests for related package or temperature variants.
What are the key specifications of PCF8575PWG4 that engineers should know?
The key specifications are a 2.5 V to 5.5 V operating range, 16 quasi-bidirectional I/O pins, 400 kHz I2C operation, three hardware address inputs, and an open-drain interrupt output. According to the Texas Instruments PCF8575 datasheet, all ports initialize high and the device supports I2C and SMBus communication. It is packaged in a 24-pin TSSOP for compact surface-mount designs.
PCF8575PWG4 vs PCF8575CPW: which is better for a 2.5 V design?
The PCF8575PWG4 is the better choice when the design must operate below 4.5 V because its specified supply range starts at 2.5 V. The PCF8575CPW is described as a 4.5 V to 5.5 V I/O expander, so it does not support the same low-voltage operating range. Both use a 24-pin TSSOP format, but verify every pin and operating condition before substitution.
When should I choose PCF8575PWG4 over PCF8575CPW?
Choose PCF8575PWG4 when the system operates at 2.5 V, 3.3 V, or 5 V and the design benefits from the wider 2.5 V to 5.5 V supply range. The PCF8575CPW is more restrictive because its listed operating range begins at 4.5 V. For 5 V-only products, compare both devices for lifecycle, sourcing, and exact ordering-code requirements rather than relying on package similarity alone.
Is PCF8575PWG4 suitable for controlling LEDs and reading switches?
Yes, the PCF8575PWG4 is suitable for reading switch states and driving LED indicators within the per-pin current limits in the manufacturer datasheet. Its quasi-bidirectional ports support input detection and latched output operation without a direction register. Ensure the LED current, external drive topology, and supply voltage remain within the published absolute-maximum and electrical-characteristic limits.
How is the interrupt output on the PCF8575PWG4 wired?
The PCF8575PWG4 interrupt output is open-drain and active-low, so it requires a pull-up to the appropriate logic supply and does not actively drive a high voltage. Multiple expanders can share the interrupt line when their address settings are unique. The Texas Instruments datasheet explains the input-change detection mechanism, which can reduce the need for continuous bus polling.
What is the best drop-in replacement for PCF8575PWG4?
PCF8575PWR is the closest documented drop-in choice because it represents the same PCF8575 device in the same 24-pin TSSOP package, with the distinction primarily related to order-code packaging. PCF8575PWE4 and PCF8575PW are additional Texas Instruments order options, while PCF8575CPW has a narrower 4.5 V to 5.5 V range. Confirm pinout, supply limits, temperature requirements, and lifecycle status before substitution.
What can replace PCF8575PWG4?
The PCF8575 family provides the closest supported replacements, including PCF8575PWR, PCF8575PWE4, and PCF8575PW, subject to exact supply, temperature, and order-code requirements. No cross-brand equivalent with verified pin-for-pin compatibility was established for the PCF8575PWG4. Review the Texas Instruments datasheet and your PCB footprint before treating any family member as a drop-in replacement.
Is there a verified cross-brand equivalent for PCF8575PWG4?
No verified cross-brand, pin-to-pin equivalent was identified for the PCF8575PWG4. A usable substitute must match the 24-pin TSSOP footprint and preserve the 2.5 V to 5.5 V operating range, 400 kHz bus support, quasi-bidirectional port behavior, address configuration, and interrupt characteristics. Do not substitute a generic I/O expander without reviewing its datasheet and testing every connected peripheral.

Dados de referência de engenharia para PCF8575PWG4 — comparação, orientação de projeto e informações de conformidade.

Guia de seleção

Choose the PCF8575PWG4 when a controller needs 16 quasi-bidirectional I/O lines, an I2C or SMBus interface, and operation from 2.5 V to 5.5 V. It is particularly useful when low-voltage operation, an active-low interrupt, or both are required. PCF8575PWR, PCF8575PWE4, and PCF8575PW are same-family ordering options that retain the 24-pin architecture, so the specific suffix should be selected according to order-code requirements and current procurement availability. PCF8575CPW shares the package and 16-bit interface but is listed for 4.5 V to 5.5 V operation, making it less appropriate for 2.5 V or 3.3 V designs. No cross-brand replacement should be treated as drop-in without verifying pin behavior, voltage thresholds, interrupt polarity, address mapping, and current ratings.

Comparação com alternativas

Parâmetro Este produto PCF8575PWR PCF8575PWE4 PCF8575PW PCF8575CPW
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Package 24-TSSOP 24-TSSOP 24-TSSOP 24-TSSOP 24-TSSOP
I/O Port Count 16 16 16 16 16
Supply Voltage Range 2.5 V to 5.5 V 2.5 V to 5.5 V 2.5 V to 5.5 V 2.5 V to 5.5 V 4.5 V to 5.5 V
Maximum I2C Clock Frequency 400 kHz 400 kHz 400 kHz 400 kHz 400 kHz
Address Inputs 3 3 3 3 3
Interrupt Output Open-drain active-low Open-drain active-low Open-drain active-low Open-drain active-low Open-drain active-low
I/O Architecture Quasi-bidirectional Quasi-bidirectional Quasi-bidirectional Quasi-bidirectional Quasi-bidirectional

Principais diferenciais

  • Wider low-voltage supply support than the PCF8575CPW (vs PCF8575CPW)
  • Sixteen integrated quasi-bidirectional I/O lines (vs PCF8575CPW)
  • Event-driven system operation through the interrupt output (vs PCF8575PWR)

Notas de projeto

Place the PCF8575PWG4 near the connector, switch bank, or indicator circuitry it serves to minimize trace length and improve signal integrity. Route SCL and SDA away from relay coils, switching-regulator inductors, and high-current LED return paths. Keep the I2C traces short and continuous, use a common ground reference, and place the required bus pull-ups near the master or according to the system-level bus topology.

Size the SDA and SCL pull-ups for the actual bus voltage, total capacitance, and sink-current capability of every connected device. The interrupt output is also open-drain and requires a pull-up. Avoid selecting unnecessarily weak pull-ups that produce slow rising edges at 400 kHz, or excessively strong pull-ups that overload the bus. Validate the complete network with an oscilloscope across the intended cable length and operating conditions.

Do not treat the quasi-bidirectional ports as ordinary push-pull GPIO outputs. A quasi-bidirectional output has a pull-up structure that can be overridden by another driver, so external circuits must respect the port current and voltage limits. Confirm whether a load requires a low output, a high output, or an input with an external pull-up. Use the manufacturer datasheet's absolute-maximum ratings to evaluate startup, disconnected-cable, and fault conditions.

Configure the three address inputs before power-on and avoid leaving their nets floating. Each device on a shared bus must have a unique address combination. Because the interrupt output is open-drain, several expanders may share one interrupt line, but the host must identify the changed device by reading the appropriate bus address. Preserve clear pin-1 orientation and follow the 24-TSSOP land pattern in the manufacturer package drawing.

Informações de conformidade

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Sem chumbo
Yes
Sem halogênios
Unknown
Minerais de conflito
Unknown

The industrial-grade PCF8575PWG4 is identified as a green, lead-free order option. RoHS, REACH, halogen-free, conflict-minerals, and automotive qualification statements require confirmation from the current manufacturer product documentation.

Dados verificados em: 2026-11-14 — dados verificados e curados pela equipe de engenharia de componentes da XAIPART

Buscas relacionadas

PCF8575PWG4 datasheet PCF8575PWG4 pinout PCF8575PWG4 datasheet pdf PCF8575PWG4 equivalent PCF8575PWG4 replacement PCF8575PWG4 vs PCF8575CPW PCF8575PWG4 TSSOP-24 footprint PCF8575PWG4 application circuit PCF8575PWG4 price PCF8575PWG4 stock Texas Instruments PCF8575PWG4 PCF8575PWG4 16-bit I2C expander

Componentes & termos relacionados

Texas Instruments PCF8575PWG4 PCF8575PWR PCF8575PWE4 PCF8575PW PCF8575CPW I/O expander GPIO expander interface IC semiconductor I2C SMBus quasi-bidirectional I/O open-drain interrupt 24-TSSOP TSSOP package family surface mount SMD LED indicator control industrial control building automation automated test equipment 400 kHz I2C 2.5 V to 5.5 V power supply
RFQ de cotação rápida
Preencha todos os detalhes — nossa equipe de vendas responderá em até 24 horas
Part number Fabricante Encapsulamento QTY Preço-alvo Total
✓
Cotação enviada!

Responderemos seu e-mail em até 24 horas

1
RFQ enviada
2
Cotação recebida
3
Pedido realizado
4
Pagamento
5
Enviado
6
Entregue
Ver detalhes da RFQ