Texas Instruments

PCM1864DBT - 24-Bit 4-Channel Audio ADC | Texas Instruments

N.º de pieza: PCM1864DBT ✓ Activo
3.3 V nominal Vdss 30-pin TSSOP Package 0.192 MHz Speed
MOQ: 1 |

PCM1864DBT Descripción general

Texas Instruments PCM1864DBT is a 24-bit, 4-channel software-controlled audio ADC with a maximum sampling rate of 192 kHz, 103 dB dynamic range, and a 30-pin TSSOP package. It operates from a single 3.3 V supply and supports both I2C and SPI control interfaces. The integrated programmable-gain amplifier and universal audio front end make it suitable for multichannel audio acquisition, active speaker monitoring, and mixed-signal systems that require compact conversion without a separate analog front end.

An audio ADC is a specialized analog-to-digital converter optimized for capturing human-audible and near-audible signals. It combines low-noise amplification, sampling, quantization, and digital filtering into a device intended for audio equipment. In the signal-chain hierarchy, PCM1864DBT belongs to the ADC and DAC class, functions as a four-channel audio ADC, and ultimately belongs to the broader semiconductor and mixed-signal IC categories. Its universal front end is intended to simplify connection of multiple analog sources while retaining programmable gain.

The principal device characteristics include 24-bit resolution, four simultaneous conversion channels, a 192 kHz maximum sampling rate, and 103 dB dynamic range. The I2C interface supports a two-wire control connection, while SPI provides a higher-throughput alternative for systems that transfer configuration data through a dedicated serial bus. A 3.3 V single-supply architecture reduces the need for negative rails in line-level audio front ends and simplifies synchronization with 3.3 V digital systems.

The PCM186x family was designed around software-controlled operation, allowing a host processor to configure the converter for the required signal path. The integrated programmable-gain amplifier gives the system additional control over input amplitude without requiring a separate gain stage for every channel. This can reduce board area and component count, although the selected gain, digital filter settings, clocking method, and input configuration must be coordinated to avoid clipping or loss of dynamic range.

Typical uses include four-channel digital audio recorders, active loudspeaker monitoring, soundbar test systems, industrial monitoring equipment, and multichannel test-and-measurement products. Its 30-pin TSSOP package is compact, but careful layout remains important because analog inputs, supply connections, ground return paths, and digital control signals share the same device. A clean 3.3 V supply and quiet analog reference arrangement are essential for preserving the advertised audio performance.

The main design trade-off is integration versus flexibility. The universal front end and integrated PGA simplify a four-channel design, but fixed functions and serial configuration require firmware support and leave less freedom than a discrete amplifier plus high-resolution converter architecture. Confirm the selected input mode, sampling rate, clock source, and filter configuration in the manufacturer datasheet before releasing a production layout.

This page organizes the PCM1864DBT specifications, application guidance, pin-layout considerations, and same-family replacement options into a practical engineering reference. It also distinguishes verified package and interface facts from detailed electrical values that require confirmation in the manufacturer datasheet, helping designers shorten component-selection and review time.

Alternativas directas para PCM1864DBT — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.

Variantes de esta serie

Modelos de la misma serie compatibles directamente con PCM1864DBT (mismo factor de forma y huella) — difiere en Maximum Sampling Rate, Operating Temperature Range, Package, Programmable Gain Amplifier, Supply Voltage.

Texas Instruments
Maximum Sampling Rate: 192 kSPS
Operating Temperature Range: -40 °C to +125 °C
Package: 30-pin TSSOP (DBT)
Comparar con PCM1864DBT →

PCM1860DBT

✅ Sustitución directa ⚠️ Especificaciones sin verificar
📦 30-TSSOP
Same family and 30-pin TSSOP footprint, but the PCM1860 provides 2 channels versus 4, a 50% channel-count reduction

📋 Alternativa de referencia (no en el catálogo)

PCM1861DBT

✅ Sustitución directa ⚠️ Especificaciones sin verificar
📦 30-TSSOP
Same family and 30-pin TSSOP footprint, but the PCM1861 provides 2 channels versus 4, a 50% channel-count reduction

📋 Alternativa de referencia (no en el catálogo)

PCM1862DBT

✅ Sustitución directa ⚠️ Especificaciones sin verificar
Texas Instruments
📦 30-TSSOP
Software-controlled audio ADC with universal front end · 2 channels · 24 bit · 192 kSPS · 103 dB · 3.3 V · Single supply · I2C and SPI

Consulte el precio

Ver hoja de datos →

PCM1863DBT

✅ Sustitución directa ⚠️ Especificaciones sin verificar
📦 30-TSSOP
Same family and 30-pin TSSOP footprint, but the PCM1863 provides 2 channels versus 4, a 50% channel-count reduction

📋 Alternativa de referencia (no en el catálogo)

PCM1865DBT

✅ Sustitución directa ⚠️ Especificaciones sin verificar
📦 30-TSSOP
Same family and 30-pin TSSOP footprint, but the PCM1865 is the 2-channel variant versus 4 channels on PCM1864DBT, a 50% channel-count reduction

📋 Alternativa de referencia (no en el catálogo)

PCM1864DBT Valores máximos y características eléctricas

Converter Type Software-controlled audio ADC
Resolución 24 bit
Number of Channels 4 channels
Maximum Sampling Rate 192 kHz
Dynamic Range 103 dB
Sampling Clock Frequency 0.192 MHz
Tensión de alimentación 3.3 V nominal
Supply Configuration Single supply
Control Interface I2C and SPI
Analog Front End Universal front end
Programmable Gain Amplifier Integrated PGA
Rango de temperatura de funcionamiento -40 C to +125 C
Encapsulado 30-pin TSSOP
Terminal Count 30 terminals
Lead Configuration Gull-wing
Tipo de montaje Surface mount

Guía de configuración de pines de PCM1864DBT 30-pin tssop

Configuración de pines para PCM1864DBT (encapsulado 30-pin tssop). Este componente analógico presenta pines de entrada, salida y alimentación. Consulte la hoja de datos del fabricante para conocer las configuraciones de los pines de ajuste de offset, compensación y habilitación. Ideal para circuitos de acondicionamiento de señal y amplificadores.

Diagrama de patillaje del encapsulado 30-pin tssop para PCM1864DBT

No hay datos detallados de patillaje disponibles para PCM1864DBT.

Consulte la hoja de datos para ver la configuración completa de patillas.

Aplicaciones típicas

PCM1864DBT es adecuado para 6 aplicacións: Four-Channel Digital Audio Recorder, Active Loudspeaker Monitoring, Soundbar and Home-Audio Test System, Industrial Sound and Vibration Monitoring, Instrumentation and Test & Measurement, USB Audio Interface.

🎧

Four-Channel Digital Audio Recorder

The PCM1864DBT suits a compact multichannel recorder because it combines four ADC channels with 24-bit resolution and a maximum sampling rate of 192 kHz. A host processor can configure the integrated programmable-gain amplifier and interface through I2C or SPI, reducing the number of separate analog conditioning and converter blocks. The 103 dB dynamic range provides useful headroom for professional or instrumentation-style capture. In practice, the record system must scale each source to use the converter range without clipping, supply a stable master clock, and provide a quiet 3.3 V rail. Firmware should also establish channel routing, gain, and digital-filter settings before acquisition begins.

🔊

Active Loudspeaker Monitoring

PCM1864DBT can monitor four amplified audio channels in an active-speaker or amplifier rack. Its four-channel architecture reduces the number of converters needed when observing multiple driver or amplifier outputs, while the integrated programmable-gain amplifier helps adapt the input range. The 24-bit converter and 103 dB dynamic range support detailed level and signal-integrity analysis. Use resistive or differential input networks selected for the speaker-output voltage range, keep monitoring traces isolated from power-stage switching paths, and configure gain separately for each channel so a transient on one input cannot clip the entire acquisition system.

📺

Soundbar and Home-Audio Test System

A soundbar production test system can use PCM1864DBT to capture several analog test points in one converter, including speaker outputs, auxiliary inputs, or microphone-derived diagnostic signals. Four channels at up to 192 kHz provide a common acquisition path for automated audio testing, and software control allows the host to change gain without physically modifying the analog network. The single 3.3 V supply simplifies interface-level planning. Keep the converter and its reference circuitry away from relay contacts, switching supplies, and loudspeaker-driver return currents because these disturbances can dominate a 103 dB-class measurement and produce misleading production results.

🏭

Industrial Sound and Vibration Monitoring

PCM1864DBT can serve as the audio-rate acquisition element in industrial monitoring equipment that compares acoustic, vibration, or machinery signals across several channels. Its four inputs permit synchronized measurements without four independent converter packages, while the programmable-gain amplifier simplifies input scaling and its 24-bit resolution preserves low-level detail. Use consistent sensor excitation and anti-alias filtering across channels. Because industrial environments often contain motor drives and switching converters, isolate analog input routing, maintain short ground returns, and verify sampled spectra with known signals before using the measurements for machine-health decisions.

🔧

Instrumentation and Test & Measurement

The PCM1864DBT is appropriate for compact instrumentation that acquires four audio-band signals and processes them digitally. Its 192 kHz maximum sampling rate supports oversampling relative to common 48 kHz audio rates, while the 103 dB dynamic range provides useful signal-to-noise performance for waveform, phase, or spectral analysis. The I2C interface suits low-rate configuration, and SPI can be preferred where deterministic clocking and faster register access are important. The instrument must define a stable sampling-clock strategy, coherent channel routing, calibration path, and input protection appropriate to the measured sources.

🖥️

USB Audio Interface

A USB audio interface can use PCM1864DBT as the analog-to-digital stage for four capture inputs. The converter's single 3.3 V supply aligns with common low-voltage audio architectures, and its I2C or SPI control path can be shared with the USB interface controller. A 24-bit, 192 kHz-capable ADC allows the interface to support high-resolution recording when the clock, driver, and host pipeline are designed consistently. Use a low-noise regulator, isolate analog input routing from USB switching noise, and program gain before enabling the USB capture stream to prevent startup transients from reaching the host.

What is the PCM1864DBT?
The PCM1864DBT is a Texas Instruments 24-bit, four-channel software-controlled audio ADC with a maximum sampling rate of 192 kHz and 103 dB dynamic range. It combines an integrated programmable-gain amplifier with a universal analog front end and supports I2C or SPI configuration. According to the Texas Instruments PCM1864 product page, the device operates from a single 3.3 V supply and is packaged in a 30-pin TSSOP.
What are the key specifications of PCM1864DBT that engineers should know?
The PCM1864DBT combines four ADC channels, 24-bit resolution, a 192 kHz maximum sampling rate, 103 dB dynamic range, and a single 3.3 V supply. It also provides I2C and SPI control, an integrated programmable-gain amplifier, and a universal analog front end. These headline specifications place it in the audio ADC category while supporting compact multichannel mixed-signal designs where a separate amplifier stage would otherwise be required.
What is the sampling rate of PCM1864DBT?
The PCM1864DBT supports a maximum sampling rate of 192 kHz with 24-bit resolution across four channels. The related 0.192 MHz sampling-clock figure corresponds to 192 kHz and is listed for the exact device by Partstack. Texas Instruments describes the PCM1864 as a four-channel software-controlled audio ADC with a universal front end.
What interface does PCM1864DBT use for configuration?
The PCM1864DBT can be configured through either I2C or SPI. I2C provides a compact two-wire connection for register writes, while SPI offers a dedicated serial interface for systems that favor a clocked data path or have higher control-bandwidth requirements. The exact supported mode, address behavior, and register sequence should be confirmed in the manufacturer datasheet.
What supply voltage does PCM1864DBT require?
The PCM1864DBT operates from a nominal 3.3 V single supply. Texas Instruments states that the PCM186x family supports single-supply operation at 3.3 V, which helps simplify analog front-end design and digital interfacing. The datasheet should be used to confirm absolute maximum ratings, recommended operating conditions, bypass capacitance, and power-supply sequencing requirements.
Where can I download the PCM1864DBT datasheet PDF?
The official PCM1864DBT documentation is available through the Texas Instruments PCM1864 product page at https://www.ti.com/product/PCM1864 and the part-specific page at https://www.ti.com/product/PCM1864/part-details/PCM1864DBT. These pages provide the manufacturer datasheet, ordering information, package details, and supported parameter information. Use the manufacturer copy for pin descriptions, register definitions, electrical limits, and recommended application circuits.
Where can I find the PCM1864DBT pinout?
The PCM1864DBT pinout is documented in the manufacturer PCM1864 datasheet under the pin-configuration and pin-description sections. The exact orderable part uses a 30-pin TSSOP package, so the schematic symbol and PCB footprint must follow the datasheet rather than a generic 30-pin symbol. Pay particular attention to supply pins, ground connections, analog inputs, clock pins, and the selected I2C or SPI interface signals.
Is PCM1864DBT suitable for a four-channel audio recorder?
Yes, the PCM1864DBT is suitable for a compact four-channel audio recorder because it provides four ADC channels, 24-bit resolution, up to 192 kHz sampling, and 103 dB dynamic range. Its integrated programmable-gain amplifier can simplify input conditioning. The record system must still provide an appropriate master clock, low-noise 3.3 V supply, clean analog layout, and firmware for configuring the PCM1864 through I2C or SPI.
Can PCM1864DBT be used for active speaker monitoring?
The PCM1864DBT can support four-channel active-speaker monitoring by sampling multiple amplifier outputs or related analog nodes. Its 103 dB dynamic range is suitable for detecting signal level, distortion-related conditions, and system noise when the analog input network is scaled correctly. Use the programmable gain to prevent full-scale clipping, and keep monitoring traces away from switching converter and digital clock paths.
PCM1864DBT vs PCM1864DBTR - which package variant should I use?
PCM1864DBT and PCM1864DBTR identify ordering or shipping variants of the same Texas Instruments PCM1864 device, and both are associated with the 30-pin TSSOP configuration. The T suffix normally identifies the tube shipment while the R suffix identifies tape-and-reel shipment. Confirm the exact suffix, quantity, and package drawing in the manufacturer part-details page before placing a production BOM.
When should I choose PCM1864DBT over a discrete amplifier and ADC?
Choose PCM1864DBT when four analog channels must be digitized in a compact 30-pin TSSOP design and the system can use its integrated programmable-gain amplifier and software-controlled configuration. Its 24-bit resolution and 192 kHz maximum rate reduce external conditioning and converter count. A discrete amplifier and ADC remain preferable when either the input topology or converter performance must be independently optimized.
What can replace PCM1864DBT on the same board?
The closest same-family alternatives are the 30-pin TSSOP PCM1860DBT, PCM1861DBT, PCM1862DBT, PCM1863DBT, and PCM1865DBT devices from Texas Instruments. Their channel counts, front-end options, and supported features can differ, so replacement requires checking the complete pin-description table, register map, clock requirements, and analog input configuration. None should be treated as interchangeable without that review.
Is PCM1864DBT the same as PCM1862DBT?
No. PCM1864DBT and PCM1862DBT are members of the PCM186x family, but they are not necessarily identical in channel count or front-end capability. PCM1864DBT is identified as a four-channel, 24-bit, 192 kHz device, while the PCM1862DBT ordering option belongs to the same 30-pin TSSOP family but may implement a different channel configuration. Review the datasheet before substituting it.
Where can I buy PCM1864DBT and check its current price?
Use the Request a Quote form on this page to request the current PCM1864DBT price, stock position, minimum order quantity, and lead time. Quote requests keep the commercial inquiry tied to the exact Texas Instruments MPN and its 30-pin TSSOP ordering variant. Request quantity breaks separately if the design requires prototype quantities, production volumes, or multiple reel or tube arrangements.
What is the lead time for PCM1864DBT?
The current lead time for PCM1864DBT depends on factory inventory, order volume, package shipment form, and purchasing terms. Use the Request a Quote form on this page and specify the required quantity, target date, and whether the order must use tube or tape-and-reel packaging. For production planning, request a committed schedule rather than relying on a generic stock estimate.
Is PCM1864DBT in stock?
PCM1864DBT stock can change with order volume and package format, so current availability should be confirmed through the Request a Quote form on this page. Include the required unit quantity and preferred 30-pin TSSOP shipment format in the request. This provides an answer tied to the exact MPN without confusing distributor inventory messages for related PCM186x orderable variants.
What design precautions apply to a PCM1864DBT analog layout?
Place analog-input and reference connections away from digital clock, serial-control, and switching-supply traces, and follow the manufacturer datasheet for component placement. A quiet 3.3 V source, local bypass capacitors, a controlled return path, and short analog traces help preserve the converter's 103 dB dynamic-range capability. Treat the four analog channels consistently to avoid gain or phase mismatch between recording paths.

Datos de referencia de ingeniería para PCM1864DBT — comparación, orientación de diseño e información de cumplimiento.

Guía de selección

Choose PCM1864DBT when the design requires four audio-band channels, 24-bit resolution, up to 192 kHz sampling, and a compact 30-pin TSSOP implementation with integrated programmable gain. Its 103 dB dynamic range and single 3.3 V supply make it particularly suitable for multichannel recorders, speaker monitoring, soundbar test systems, and instrumentation. The 2-channel PCM1860DBT, PCM1861DBT, PCM1862DBT, PCM1863DBT, or PCM1865DBT can reuse the family package context, but each may reduce channel count or change front-end behavior, so verify the full pin and register tables before substitution. For a new design where only one or two channels are required, a smaller converter may reduce board area and cost more meaningfully than reusing this four-channel package. Conversely, when channel count, software configuration, compactness, and integrated gain matter more than maximum analog flexibility, PCM1864DBT provides a focused solution with two control-interface choices.

Comparación con alternativas

Parámetro Este producto PCM1860DBT PCM1861DBT PCM1862DBT PCM1863DBT PCM1865DBT
Package 30-TSSOP 30-TSSOP 30-TSSOP 30-TSSOP 30-TSSOP 30-TSSOP
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Channel Count 4 channels 2 channels 2 channels 2 channels 2 channels 2 channels
Resolution 24 bit 24 bit 24 bit 24 bit 24 bit 24 bit
Maximum Sampling Rate 192 kHz 192 kHz 192 kHz 192 kHz 192 kHz 192 kHz
Supply Voltage 3.3 V nominal, single supply 3.3 V nominal, single supply 3.3 V nominal, single supply 3.3 V nominal, single supply 3.3 V nominal, single supply 3.3 V nominal, single supply
Control Interface I2C and SPI I2C and SPI I2C and SPI I2C and SPI I2C and SPI I2C and SPI
Integrated PGA Yes Yes Yes Yes Yes Yes
Operating Temperature Range -40 C to +125 C -40 C to +125 C -40 C to +125 C -40 C to +125 C -40 C to +125 C -40 C to +125 C

Diferenciadores clave

  • Four-channel integration reduces converter count (frente a PCM1862DBT)
  • High-resolution audio conversion (frente a PCM1860DBT)
  • Single-supply 3.3 V operation (frente a PCM1865DBT)

Notas de diseño

Use the manufacturer datasheet as the authority for the exact 30-pin TSSOP footprint and pin assignments. Keep analog input traces short, place required bypass components at their specified pins, and route digital clock and serial-control signals away from the analog input and reference area. The 103 dB dynamic-range figure can be undermined by coupling from switching supplies, relay contacts, or high-current return paths even when the converter itself operates correctly.

Power PCM1864DBT from a low-noise 3.3 V source with the decoupling network specified by Texas Instruments. Because this device combines a four-channel analog front end with digital control, supply noise can appear directly in the conversion result. Keep the analog and digital return paths coordinated, avoid sharing long narrow necklaces with amplifier output currents, and verify power sequencing if the host controller and converter are independently enabled.

Program the integrated PGA and input routing before starting acquisition so that transient levels do not clip the converter. Maintain consistent input scaling across all four channels if phase, level, or frequency-response comparisons are required. Define the master-clock and sampling mode in firmware, allow the selected digital filter to settle, and validate synchronization with a known test signal before treating the four channels as phase-coherent measurements.

Do not substitute a PCM186x family member based only on the shared 30-TSSOP outline. Review the pin-description table, analog input configuration, supported clocking, register map, and intended channel count for the selected replacement. Also verify the exact shipment suffix: PCM1864DBT is associated with tube ordering, while PCM1864DBTR is associated with tape-and-reel ordering, and the correct quantity break should match the assembly method.

Información de cumplimiento

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Libre de plomo
Unknown
Libre de halógenos
Unknown
Minerales en conflicto
Unknown

No explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status was identified for the exact PCM1864DBT orderable part. Confirm current compliance documentation with Texas Instruments.

Búsquedas relacionadas

PCM1864DBT datasheet PCM1864DBT datasheet pdf PCM1864DBT pinout PCM1864DBT specifications PCM1864DBT 30-TSSOP PCM1864DBT I2C SPI PCM1864DBT price PCM1864DBT stock PCM1864DBT replacement PCM1864DBT equivalent Texas Instruments PCM1864DBT PCM1864DBT audio ADC PCM1864DBT vs PCM1862DBT PCM1864DBT four channel recorder

Componentes & términos relacionados

Texas Instruments PCM1864DBT PCM1864DBTR PCM1860DBT PCM1861DBT PCM1862DBT PCM1863DBT PCM1865DBT PCM186x audio ADC analog-to-digital converter mixed-signal IC semiconductor programmable-gain amplifier PGA universal front end I2C SPI 24-bit resolution 192 kHz sampling rate 103 dB dynamic range 30-TSSOP TSSOP package family surface-mount device SMD
RFQ de presupuesto rápido
Complete los detalles — nuestro equipo de ventas responderá en un plazo de 24 horas
Número de pieza Fabricante Encapsulado QTY Precio objetivo Total
✓
¡Presupuesto enviado!

Responderemos a su correo electrónico en un plazo de 24 horas

1
RFQ enviado
2
Presupuesto recibido
3
Pedido realizado
4
Pago
5
Enviado
6
Entregado
Ver detalles del RFQ