PCM1864DBT - 24-Bit 4-Channel Audio ADC | Texas Instruments
料号: PCM1864DBT ✓ 量产中PCM1864DBT 概述
An audio ADC is a specialized analog-to-digital converter optimized for capturing human-audible and near-audible signals. It combines low-noise amplification, sampling, quantization, and digital filtering into a device intended for audio equipment. In the signal-chain hierarchy, PCM1864DBT belongs to the ADC and DAC class, functions as a four-channel audio ADC, and ultimately belongs to the broader semiconductor and mixed-signal IC categories. Its universal front end is intended to simplify connection of multiple analog sources while retaining programmable gain.
The principal device characteristics include 24-bit resolution, four simultaneous conversion channels, a 192 kHz maximum sampling rate, and 103 dB dynamic range. The I2C interface supports a two-wire control connection, while SPI provides a higher-throughput alternative for systems that transfer configuration data through a dedicated serial bus. A 3.3 V single-supply architecture reduces the need for negative rails in line-level audio front ends and simplifies synchronization with 3.3 V digital systems.
The PCM186x family was designed around software-controlled operation, allowing a host processor to configure the converter for the required signal path. The integrated programmable-gain amplifier gives the system additional control over input amplitude without requiring a separate gain stage for every channel. This can reduce board area and component count, although the selected gain, digital filter settings, clocking method, and input configuration must be coordinated to avoid clipping or loss of dynamic range.
Typical uses include four-channel digital audio recorders, active loudspeaker monitoring, soundbar test systems, industrial monitoring equipment, and multichannel test-and-measurement products. Its 30-pin TSSOP package is compact, but careful layout remains important because analog inputs, supply connections, ground return paths, and digital control signals share the same device. A clean 3.3 V supply and quiet analog reference arrangement are essential for preserving the advertised audio performance.
The main design trade-off is integration versus flexibility. The universal front end and integrated PGA simplify a four-channel design, but fixed functions and serial configuration require firmware support and leave less freedom than a discrete amplifier plus high-resolution converter architecture. Confirm the selected input mode, sampling rate, clock source, and filter configuration in the manufacturer datasheet before releasing a production layout.
This page organizes the PCM1864DBT specifications, application guidance, pin-layout considerations, and same-family replacement options into a practical engineering reference. It also distinguishes verified package and interface facts from detailed electrical values that require confirmation in the manufacturer datasheet, helping designers shorten component-selection and review time.
直接替换替代料: PCM1864DBT ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: PCM1864DBT (相同外形与封装尺寸) ——差异在于 Maximum Sampling Rate, Operating Temperature Range, Package, Programmable Gain Amplifier, Supply Voltage.
PCM1860DBT
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
PCM1861DBT
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
PCM1862DBT
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →PCM1863DBT
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
PCM1865DBT
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
PCM1864DBT 最大额定值与电气特性
| Converter Type | Software-controlled audio ADC |
| 分辨率 | 24 bit |
| Number of Channels | 4 channels |
| Maximum Sampling Rate | 192 kHz |
| Dynamic Range | 103 dB |
| Sampling Clock Frequency | 0.192 MHz |
| 电源电压 | 3.3 V nominal |
| Supply Configuration | Single supply |
| Control Interface | I2C and SPI |
| Analog Front End | Universal front end |
| Programmable Gain Amplifier | Integrated PGA |
| 工作温度范围 | -40 C to +125 C |
| 封装 | 30-pin TSSOP |
| Terminal Count | 30 terminals |
| Lead Configuration | Gull-wing |
| 安装类型 | Surface mount |
PCM1864DBT 30-pin tssop 引脚配置指南
PCM1864DBT(30-pin tssop 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。
暂无详细引脚数据: PCM1864DBT.
请参阅 数据手册 以查看完整引脚配置。
典型应用
PCM1864DBT 适用于 6 应用s: Four-Channel Digital Audio Recorder, Active Loudspeaker Monitoring, Soundbar and Home-Audio Test System, Industrial Sound and Vibration Monitoring, Instrumentation and Test & Measurement, USB Audio Interface.
Four-Channel Digital Audio Recorder
The PCM1864DBT suits a compact multichannel recorder because it combines four ADC channels with 24-bit resolution and a maximum sampling rate of 192 kHz. A host processor can configure the integrated programmable-gain amplifier and interface through I2C or SPI, reducing the number of separate analog conditioning and converter blocks. The 103 dB dynamic range provides useful headroom for professional or instrumentation-style capture. In practice, the record system must scale each source to use the converter range without clipping, supply a stable master clock, and provide a quiet 3.3 V rail. Firmware should also establish channel routing, gain, and digital-filter settings before acquisition begins.
推荐
Active Loudspeaker Monitoring
PCM1864DBT can monitor four amplified audio channels in an active-speaker or amplifier rack. Its four-channel architecture reduces the number of converters needed when observing multiple driver or amplifier outputs, while the integrated programmable-gain amplifier helps adapt the input range. The 24-bit converter and 103 dB dynamic range support detailed level and signal-integrity analysis. Use resistive or differential input networks selected for the speaker-output voltage range, keep monitoring traces isolated from power-stage switching paths, and configure gain separately for each channel so a transient on one input cannot clip the entire acquisition system.
推荐
Soundbar and Home-Audio Test System
A soundbar production test system can use PCM1864DBT to capture several analog test points in one converter, including speaker outputs, auxiliary inputs, or microphone-derived diagnostic signals. Four channels at up to 192 kHz provide a common acquisition path for automated audio testing, and software control allows the host to change gain without physically modifying the analog network. The single 3.3 V supply simplifies interface-level planning. Keep the converter and its reference circuitry away from relay contacts, switching supplies, and loudspeaker-driver return currents because these disturbances can dominate a 103 dB-class measurement and produce misleading production results.
推荐
Industrial Sound and Vibration Monitoring
PCM1864DBT can serve as the audio-rate acquisition element in industrial monitoring equipment that compares acoustic, vibration, or machinery signals across several channels. Its four inputs permit synchronized measurements without four independent converter packages, while the programmable-gain amplifier simplifies input scaling and its 24-bit resolution preserves low-level detail. Use consistent sensor excitation and anti-alias filtering across channels. Because industrial environments often contain motor drives and switching converters, isolate analog input routing, maintain short ground returns, and verify sampled spectra with known signals before using the measurements for machine-health decisions.
推荐
Instrumentation and Test & Measurement
The PCM1864DBT is appropriate for compact instrumentation that acquires four audio-band signals and processes them digitally. Its 192 kHz maximum sampling rate supports oversampling relative to common 48 kHz audio rates, while the 103 dB dynamic range provides useful signal-to-noise performance for waveform, phase, or spectral analysis. The I2C interface suits low-rate configuration, and SPI can be preferred where deterministic clocking and faster register access are important. The instrument must define a stable sampling-clock strategy, coherent channel routing, calibration path, and input protection appropriate to the measured sources.
推荐
USB Audio Interface
A USB audio interface can use PCM1864DBT as the analog-to-digital stage for four capture inputs. The converter's single 3.3 V supply aligns with common low-voltage audio architectures, and its I2C or SPI control path can be shared with the USB interface controller. A 24-bit, 192 kHz-capable ADC allows the interface to support high-resolution recording when the clock, driver, and host pipeline are designed consistently. Use a low-noise regulator, isolate analog input routing from USB switching noise, and program gain before enabling the USB capture stream to prevent startup transients from reaching the host.
推荐
工程参考数据: PCM1864DBT ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | PCM1860DBT | PCM1861DBT | PCM1862DBT | PCM1863DBT | PCM1865DBT |
|---|---|---|---|---|---|---|
| Package | 30-TSSOP | 30-TSSOP | 30-TSSOP | 30-TSSOP | 30-TSSOP | 30-TSSOP |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Channel Count | 4 channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels |
| Resolution | 24 bit | 24 bit | 24 bit | 24 bit | 24 bit | 24 bit |
| Maximum Sampling Rate | 192 kHz | 192 kHz | 192 kHz | 192 kHz | 192 kHz | 192 kHz |
| Supply Voltage | 3.3 V nominal, single supply | 3.3 V nominal, single supply | 3.3 V nominal, single supply | 3.3 V nominal, single supply | 3.3 V nominal, single supply | 3.3 V nominal, single supply |
| Control Interface | I2C and SPI | I2C and SPI | I2C and SPI | I2C and SPI | I2C and SPI | I2C and SPI |
| Integrated PGA | Yes | Yes | Yes | Yes | Yes | Yes |
| Operating Temperature Range | -40 C to +125 C | -40 C to +125 C | -40 C to +125 C | -40 C to +125 C | -40 C to +125 C | -40 C to +125 C |
关键差异点
- Four-channel integration reduces converter count (对比 PCM1862DBT)
- High-resolution audio conversion (对比 PCM1860DBT)
- Single-supply 3.3 V operation (对比 PCM1865DBT)
设计说明
Use the manufacturer datasheet as the authority for the exact 30-pin TSSOP footprint and pin assignments. Keep analog input traces short, place required bypass components at their specified pins, and route digital clock and serial-control signals away from the analog input and reference area. The 103 dB dynamic-range figure can be undermined by coupling from switching supplies, relay contacts, or high-current return paths even when the converter itself operates correctly.
Power PCM1864DBT from a low-noise 3.3 V source with the decoupling network specified by Texas Instruments. Because this device combines a four-channel analog front end with digital control, supply noise can appear directly in the conversion result. Keep the analog and digital return paths coordinated, avoid sharing long narrow necklaces with amplifier output currents, and verify power sequencing if the host controller and converter are independently enabled.
Program the integrated PGA and input routing before starting acquisition so that transient levels do not clip the converter. Maintain consistent input scaling across all four channels if phase, level, or frequency-response comparisons are required. Define the master-clock and sampling mode in firmware, allow the selected digital filter to settle, and validate synchronization with a known test signal before treating the four channels as phase-coherent measurements.
Do not substitute a PCM186x family member based only on the shared 30-TSSOP outline. Review the pin-description table, analog input configuration, supported clocking, register map, and intended channel count for the selected replacement. Also verify the exact shipment suffix: PCM1864DBT is associated with tube ordering, while PCM1864DBTR is associated with tape-and-reel ordering, and the correct quantity break should match the assembly method.
合规信息
No explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status was identified for the exact PCM1864DBT orderable part. Confirm current compliance documentation with Texas Instruments.