PCM3000E/2K - 18-Bit Stereo Audio Codec | Texas Instruments
N.º de pieza: PCM3000E/2K ✓ ActivoPCM3000E/2K Descripción general
An audio codec is an interface IC that converts analog audio signals into digital data and reconstructs digital audio streams into analog output. In the broader semiconductor hierarchy, PCM3000E/2K belongs to the audio codec family within interface integrated circuits. Combining both conversion directions in one package reduces component count, simplifies board routing, and supports compact consumer audio products such as sound cards, home-audio accessories, and USB audio equipment.
The device provides 18-bit stereo conversion, two ADC channels, two DAC channels, and a serial interface. These features make PCM3000E/2K appropriate for designs that need a straightforward stereo signal path rather than a high-channel-count professional codec. Its single-ended analog architecture also simplifies board design by avoiding the balanced input and output networks commonly required by professional audio interfaces.
Texas Instruments describes PCM3000 and PCM3001 as low-cost, single-chip stereo codecs fabricated using an advanced CMOS process. Both devices are offered in a compact 28-pin SSOP package. The PCM3001 variant can be pin-programmed for different data formats, whereas the PCM3000 family is primarily intended for applications using its supported serial format. The PCM3000E/2K ordering code identifies the tape-and-reel configuration.
Typical uses include USB sound-card signal conditioning, multimedia speaker and headphone interfaces, portable audio accessories, digital recording equipment, and cost-sensitive stereo playback systems. In each case, the device can serve as the central conversion stage between analog transducers and a digital audio controller. Digital audio quality still depends on correct clocking, analog layout, grounding, decoupler placement, and suitable output and input filtering.
PCB design should keep analog input and output traces away from digital clock and serial-data paths, while providing a low-impedance ground plane beneath the codec. Follow the manufacturer datasheet for the recommended power, clock, and signal connections. The most important replacement check is not merely the 28-pin SSOP outline but also the exact signal interface, clocking requirements, analog pin functions, and supported data format.
This page organizes the PCM3000E/2K specifications, lifecycle information, sourcing path, compatible alternatives, comparison points, and practical integration guidance into one engineering-focused reference. It also distinguishes genuine package-and-interface drop-in options from functionally similar codecs that require different pin assignments or redesigned analog and digital circuitry.
Alternativas directas para PCM3000E/2K — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con PCM3000E/2K (mismo factor de forma y huella) — difiere en Package.
PCM3000E
✅ Sustitución directaConsulte el precio
Ver hoja de datos →PCM3001/2K
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
PCM3000E
✅ Sustitución directaConsulte el precio
Ver hoja de datos →PCM3000E/2K Especificaciones
| Device Type | Stereo audio codec |
| Converter Resolution | 18 bit |
| ADC Channels | 2 channels |
| DAC Channels | 2 channels |
| Digital Audio Interface | Serial |
| Analog Input Configuration | Single-ended |
| Analog Output Configuration | Single-ended |
| Encapsulado | 28-SSOP, 0.209 inch (5.30 mm) width |
| Recuento de pines | 28 pins |
| Rango de temperatura de funcionamiento | -25 C to +85 C |
| Manufacturing Technology | CMOS |
| Packaging | Tape & Reel |
| Product Status | Active |
| Minimum Order Quantity | 2000 pieces |
| Lead Time | 18 weeks |
| RoHS Compliance | unknown |
| REACH Compliance | unknown |
| AEC-Q100 Qualification | not_applicable |
Guía de configuración de pines de PCM3000E/2K 28-ssop, 0.209 inch (5.30 mm) width
Configuración de pines para PCM3000E/2K (encapsulado 28-ssop, 0.209 inch (5.30 mm) width). La numeración de pines, las funciones y los diagramas de conexión se definen en la hoja de datos del fabricante. Consúltela para conocer el footprint exacto y las directrices de soldadura.
No hay datos detallados de patillaje disponibles para PCM3000E/2K.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
PCM3000E/2K es adecuado para 6 aplicacións: USB Audio Interface, Digital Speaker Amplifier Front End, Multimedia Recording Accessory, Home Audio Accessory, Portable Audio Player, Consumer Audio Interface Card.
USB Audio Interface
PCM3000E/2K can provide the analog-to-digital and digital-to-analog conversion stage in a cost-sensitive USB audio interface. Its 18-bit resolution, two ADC channels, and two DAC channels cover basic stereo capture and playback without requiring separate converters. The single-ended analog paths reduce external circuitry, while the 28-SSOP package supports compact layouts. The USB controller must be compatible with the PCM3000 serial format and supply the required master-clock and data signals. Layout should separate analog nets from digital clock traces and use the manufacturer's recommended decoupling and grounding arrangement.
Recomendado
Digital Speaker Amplifier Front End
PCM3000E/2K is suitable for decoding a digital audio stream into a single-ended analog signal for an external power amplifier. Its two DAC channels support stereo playback, while the 18-bit conversion format suits consumer equipment requiring more precision than an 8-bit or 16-bit system. The codec should be placed close to the amplifier input so that the sensitive analog output is not exposed to long PCB traces. External filtering, gain adjustment, and output impedance must be selected to match the target amplifier input.
Recomendado
Multimedia Recording Accessory
PCM3000E/2K can serve as the central stereo codec in a compact multimedia recording accessory that captures microphone or line-level audio and plays back stored digital sound. Two ADC channels support stereo capture, and two DAC channels support stereo monitoring or playback. Its single-ended analog input and output keep the analog network manageable for a cost-focused design. Use the manufacturer pin and typical-application information to establish the required input gain, filtering, clock source, and digital data connection to the recording controller.
Recomendado
Home Audio Accessory
PCM3000E/2K fits home-audio accessories that need a compact stereo playback path, including digital sources, speaker controllers, and analog input expanders. The device provides 18-bit DAC resolution, two output channels, and a serial digital interface in a 28-SSOP package. Because the outputs are single-ended, the downstream amplifier should provide the required gain and input impedance. The single-chip conversion approach reduces the number of separate ICs compared with separate ADC and DAC packages, but analog filtering and layout quality remain central to avoiding audible distortion.
Recomendado
Portable Audio Player
PCM3000E/2K can be used in a portable stereo audio player where low component count and a compact analog section are important. Two 18-bit DAC channels reproduce left and right digital audio channels, while the serial interface connects to a storage or decoding controller. The 28-SSOP package requires careful footprint layout but avoids the area occupied by separate ADC and DAC packages. Battery-operated designs should evaluate the complete analog power path and the codec's operating requirements under the system's supply conditions before finalizing the architecture.
Recomendado
Consumer Audio Interface Card
PCM3000E/2K supports a simple consumer add-in card that bridges analog audio connectors and a digital audio controller. Its two ADC channels accept stereo analog input, and its two DAC channels provide stereo analog output for monitoring or playback. The 18-bit interface offers adequate resolution for cost-sensitive consumer equipment, and the single-ended architecture reduces connector circuitry. Digital isolation, clock distribution, ground partitioning, and connector grounding should be designed together because codec performance can be limited by ground noise even when the converter resolution is adequate.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para PCM3000E/2K — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | PCM3000 | PCM3001/2K | PCM3000E |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 28-SSOP | 28-SSOP | 28-SSOP | 28-SSOP |
| Device Type | Stereo audio codec | Stereo audio codec | Stereo audio codec | Stereo audio codec |
| Converter Resolution | 18 bit | 18 bit | 18 bit | 18 bit |
| ADC Channels | 2 channels | 2 channels | 2 channels | 2 channels |
| DAC Channels | 2 channels | 2 channels | 2 channels | 2 channels |
| Digital Interface | Serial | Serial | Serial with pin-programmable data formats | Serial |
| Analog Configuration | Single-ended input and output | Single-ended input and output | Single-ended input and output | Single-ended input and output |
| Manufacturing Technology | CMOS | CMOS | CMOS | CMOS |
Diferenciadores clave
- Single-chip stereo capture and playback (frente a PCM3001/2K)
- Same compact SSOP integration level (frente a PCM3000)
- Fixed interface for simpler consumer designs (frente a PCM3001/2K)
Notas de diseño
Place the codec near the digital audio controller but keep the analog input and output section physically separated from serial clock and data routing. The 28-SSOP footprint should follow the manufacturer land pattern exactly, including pin-1 orientation and lead spacing. A continuous ground reference should pass beneath the device, while analog and digital return paths should avoid sharing narrow traces that carry switching currents.
Connect the analog input and output pins to their filtering networks with short traces, and position external components close to the corresponding codec pins. Digital data and clock lines should not run beneath sensitive analog nodes or between analog ground paths. If the serial clock is fast enough to radiate, constrain it to the digital region and maintain continuous ground shielding on adjacent layers.
Use the supply topology and decoupling arrangement specified in the Texas Instruments PCM3000 family datasheet. The codec combines analog and digital functions, so a shared supply can transfer noise between sections. Provide local bypass capacitance at the supply pins, keep the supply return path low-impedance, and verify startup sequencing and operating voltage against the selected device revision before releasing the design for production.
Do not treat equal SSOP-28 dimensions as proof of drop-in compatibility. Before replacing PCM3000E/2K, compare every pin name, power pin, clock input, serial interface signal, analog input function, and data-format selection. PCM3001/2K adds pin-programmable formats, so an otherwise identical footprint may require different controller settings or board strapping.
Información de cumplimiento
The available product excerpts do not state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. AEC-Q100 is not applicable because the product is listed as a consumer audio codec rather than an automotive-qualified device.