PI7C9X1170ABLEX - I2C/SPI to UART Bridge | Diodes
N.º de pieza: PI7C9X1170ABLEX ✓ ActivoPI7C9X1170ABLEX Descripción general
An I2C-to-UART bridge is an interface IC that translates transactions between two serial protocols with different clocking and framing conventions. The PI7C9X1170 belongs to the broader UART interface controller category and combines serial bus conversion with programmable I/O, allowing a compact host interface to connect sensors, flash memory, converters, and other peripheral devices over I2C or SPI.
According to the manufacturer datasheet, the controller supports data rates up to 33 Mbps and includes as many as eight additional programmable GPIO pins. These resources let the device collect sideband status signals, control chip-select or reset lines, or monitor external circuit conditions while the main serial channel handles data transfer. The compact TSSOP package also supports cost-sensitive, space-constrained handheld and embedded systems.
The PI7C9X1170 is described as guaranteeing low operating and sleeping current, making power management an important part of its architecture. A bridge controller can remain connected to a battery-powered peripheral while providing a defined low-power operating state. Exact supply-voltage limits, quiescent-current figures, and logic thresholds should be confirmed from the electrical-characteristics tables in the manufacturer datasheet before the device is placed in a production design.
Typical uses include battery-powered instruments, sensor-hub boards, flash-memory access systems, and embedded instruments that need to translate I2C or SPI transactions into a UART stream. The bridge is particularly useful when an existing UART-capable processor lacks spare I2C or SPI controllers, or when consolidating peripheral access reduces the pin count and software complexity of a baseboard.
Confirm the package pin assignments, signal levels, clock configuration, and supported host protocol before layout release. Keep UART and serial-clock traces short, provide the required bypass capacitance at the supply pins, and validate the bridge configuration in firmware before placing it in a timing-critical or high-voltage environment.
Alternativas directas para PI7C9X1170ABLEX — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con PI7C9X1170ABLEX (mismo factor de forma y huella).
PI7C9X1170ABLE
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
PI7C9X1170BBLEX
✅ Sustitución directaConsulte el precio
Ver hoja de datos →PI7C9X1170ABLEX Valores máximos y características eléctricas
| Product Type | I2C-bus/SPI to single-channel UART bridge controller |
| Maximum Data Rate | 33 Mbps |
| UART Channels | 1 channel |
| Source Bus Support | I2C-bus or SPI |
| Programmable GPIO Count | Up to 8 pins |
| Encapsulado | 16-pin TSSOP |
| Package Type | Thin Shrink Small Outline Package (TSSOP) |
| Terminal Form | Gull wing |
| Package Shape | Rectangular |
| Temperature Grade | Industrial |
| Tipo de montaje | Surface mount |
Guía de configuración de pines de PI7C9X1170ABLEX rectangular
Configuración de pines para PI7C9X1170ABLEX (encapsulado rectangular). Este dispositivo de potencia presenta terminales de puerta, drenador y fuente. Para encapsulados no polarizados, consulte la hoja de datos del fabricante para conocer la orientación exacta del pin 1 y los detalles del footprint. Las aplicaciones habituales incluyen el diseño de fuentes de alimentación, el accionamiento de motores y la conmutación de cargas.
No hay datos detallados de patillaje disponibles para PI7C9X1170ABLEX.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
PI7C9X1170ABLEX es adecuado para 6 aplicacións: Battery-Powered Sensor Hubs, Embedded Data-Acquisition Systems, Flash-Memory Access and Configuration, Handheld Test and Measurement Instruments, Industrial Control and Peripheral Consolidation, Portable and Wearable Device Interfaces.
Battery-Powered Sensor Hubs
The PI7C9X1170ABLEX fits sensor-hub boards that collect measurements through I2C or SPI and forward them through a UART link. Its single-channel bridge architecture avoids dedicating a processor I/O port to each peripheral bus, while the eight programmable GPIO pins can handle module enables, interrupt acknowledgments, or fault flags. The manufacturer highlights low operating and sleeping current for portable systems, and the 16-TSSOP package preserves board area. Firmware should enable sleep during idle periods and reinitialize the interface after wake-up so the host and peripheral remain synchronized.
Recomendado
Embedded Data-Acquisition Systems
In an embedded measurement system, the PI7C9X1170ABLEX can place high-speed peripheral data behind a UART transport while accepting commands from the bus side. The manufacturer specifies operation at data rates up to 33 Mbps, giving the design headroom for demanding converters and memory devices. Because the device also provides up to eight programmable GPIO pins, the same circuit can capture trigger, status, or interlock signals without expanding the host pin count. Validate the bridge timing and maximum sustained transfer rate in the target system.
Recomendado
Flash-Memory Access and Configuration
The PI7C9X1170ABLEX can bridge a controller's UART commands to an I2C or SPI flash device, simplifying a design that otherwise requires a dedicated serial-memory interface. Protocol translation concentrates the flash-access sequencing in one controller, while the GPIO pins can supply a chip-select, write-protect, or fault indication where the application needs it. Designers should verify the supported SPI mode, address width, and maximum operating clock against the flash datasheet. Power-down and wake-up handling must also prevent unintended memory writes when the host resets.
Recomendado
Handheld Test and Measurement Instruments
A handheld instrument often combines several serial peripherals with a UART-based host or service connector. The PI7C9X1170ABLEX consolidates that connectivity in one 16-TSSOP controller, and its manufacturer-described low sleeping current supports battery-powered operation between measurement cycles. The programmable GPIO pins can supervise instrument-ready, trigger, or charger-status signals. Designers should use the datasheet power and timing tables to select wake-up behavior and confirm that the chosen temperature grade covers the instrument's ambient range.
Recomendado
Industrial Control and Peripheral Consolidation
Industrial controller boards can use the PI7C9X1170ABLEX to connect an I2C or SPI peripheral bank to a UART-based service processor or remote communication module. This is useful when the main control processor has limited serial-controller resources or when a legacy UART infrastructure must retain access to modern peripherals. The bridge occupies a compact 16-TSSOP footprint, while the GPIO outputs can provide reset, alert, or channel-enable control. Industrial deployments should verify supply tolerances, temperature grade, and isolation requirements in the final system architecture.
Recomendado
Portable and Wearable Device Interfaces
The PI7C9X1170ABLEX is suitable for portable products that need to bridge compact sensors or radio-support components into a UART stream. Its small TSSOP package, up to 33 Mbps serial capability, and low operating and sleeping current suit area- and power-constrained designs. Up to eight programmable GPIO pins can be assigned to motion wake-up, strap selection, or peripheral status functions. The bridge should be placed near the serial devices it serves to keep clock and data traces short, while UART routing should avoid noisy switching-converter regions.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para PI7C9X1170ABLEX — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | PI7C9X1170ABLE | PI7C9X1170BBLEX |
|---|---|---|---|
| Brand | Diodes Incorporated | Diodes Incorporated | Diodes Incorporated |
| Package | 16-TSSOP | 16-TSSOP | 16-TSSOP |
| Mounting Type | Surface mount | Surface mount | Surface mount |
Diferenciadores clave
- Single-chip protocol translation with programmable sideband control (frente a PI7C9X1170BBLEX)
- High-speed serial performance in a compact package (frente a PI7C9X1170ABLE)
- Designed for portable power constraints (frente a PI7C9X1170BBLEX)
Notas de diseño
Place the PI7C9X1170ABLEX close to the I2C or SPI peripheral it serves and route the UART interface toward the host connector. Keep serial clock and data traces short, avoid stubs, and maintain a continuous ground reference beneath the signal paths. The eight GPIO lines should also be routed away from high-voltage switching nodes, especially when the bridge is used near an RF or power-conversion section.
Decouple the device at its supply pins with the capacitance specified by the manufacturer datasheet and place it close to the package power and ground connections. Review operating and sleeping current in the selected clock configuration rather than estimating from the headline data-rate rating. For battery-powered equipment, define a deterministic wake sequence that prevents bus traffic before the peripheral and bridge clocks are stable.
Treat the I2C or SPI clock as a critical timing signal and verify pull-up values, bus capacitance, rise time, and the maximum supported clock in the datasheet. UART signals crossing between domains may require level translation if the bridge and host use different logic standards. Confirm whether signals are driven during sleep so that a partially powered peripheral cannot receive corrupted commands.
Do not select a family member solely because it has the same package outline. Ordering suffixes can identify different grades, packing arrangements, or configurations, so verify the PI7C9X1170 ordering table before substitution. Also validate the device's framing, GPIO multiplexing, and firmware configuration; a pin-compatible package does not by itself guarantee identical peripheral behavior.
Información de cumplimiento
The industrial temperature grade is identified in the catalog listing. Compliance declarations are not stated in the verified excerpts and remain unconfirmed.