Diodes Incorporated

PI7C9X1170ABLEX - I2C/SPI to UART Bridge | Diodes

부품 번호: PI7C9X1170ABLEX ✓ 활성
16-pin TSSOP Package
MOQ: 1 |

PI7C9X1170ABLEX 개요

The Diodes Incorporated PI7C9X1170ABLEX is a single-channel I2C-bus or SPI to UART bridge controller that supports data rates up to 33 Mbps and provides eight programmable general-purpose I/O pins in a 16-pin TSSOP package. It is designed for systems where a serial peripheral interface must be connected to a UART-based host, embedded controller, or data-acquisition equipment.

An I2C-to-UART bridge is an interface IC that translates transactions between two serial protocols with different clocking and framing conventions. The PI7C9X1170 belongs to the broader UART interface controller category and combines serial bus conversion with programmable I/O, allowing a compact host interface to connect sensors, flash memory, converters, and other peripheral devices over I2C or SPI.

According to the manufacturer datasheet, the controller supports data rates up to 33 Mbps and includes as many as eight additional programmable GPIO pins. These resources let the device collect sideband status signals, control chip-select or reset lines, or monitor external circuit conditions while the main serial channel handles data transfer. The compact TSSOP package also supports cost-sensitive, space-constrained handheld and embedded systems.

The PI7C9X1170 is described as guaranteeing low operating and sleeping current, making power management an important part of its architecture. A bridge controller can remain connected to a battery-powered peripheral while providing a defined low-power operating state. Exact supply-voltage limits, quiescent-current figures, and logic thresholds should be confirmed from the electrical-characteristics tables in the manufacturer datasheet before the device is placed in a production design.

Typical uses include battery-powered instruments, sensor-hub boards, flash-memory access systems, and embedded instruments that need to translate I2C or SPI transactions into a UART stream. The bridge is particularly useful when an existing UART-capable processor lacks spare I2C or SPI controllers, or when consolidating peripheral access reduces the pin count and software complexity of a baseboard.

Confirm the package pin assignments, signal levels, clock configuration, and supported host protocol before layout release. Keep UART and serial-clock traces short, provide the required bypass capacitance at the supply pins, and validate the bridge configuration in firmware before placing it in a timing-critical or high-voltage environment.

드롭인 대체품: PI7C9X1170ABLEX — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.

이 시리즈의 변형

다음과 드롭인 호환되는 동일 시리즈 모델: PI7C9X1170ABLEX (동일 폼 팩터 및 풋프린트).

PI7C9X1170ABLE

✅ 드롭인
📦 16-TSSOP
Same PI7C9X1170 family and 16-TSSOP bridge category; ordering suffix differs, with grade and packing details requiring confirmation (-0% functional difference where the base configuration is identical)

📋 참조 대체품 (카탈로그에 없음)

PI7C9X1170BBLEX

✅ 드롭인
Diodes Incorporated
📦 16-TSSOP
I2C-bus/SPI to single-channel UART bridge controller · 33 Mbps · I2C-bus and SPI · 1 channel · Up to 8 pins · 16-pin TSSOP · 16 terminals · Rectangular

가격 문의

데이터시트 보기 →

PI7C9X1170ABLEX 최대 정격 & 전기적 특성

Product Type I2C-bus/SPI to single-channel UART bridge controller
Maximum Data Rate 33 Mbps
UART Channels 1 channel
Source Bus Support I2C-bus or SPI
Programmable GPIO Count Up to 8 pins
패키지 16-pin TSSOP
Package Type Thin Shrink Small Outline Package (TSSOP)
Terminal Form Gull wing
Package Shape Rectangular
Temperature Grade Industrial
실장 유형 Surface mount

PI7C9X1170ABLEX rectangular 핀 구성 가이드

PI7C9X1170ABLEX(rectangular 패키지)의 핀 구성입니다. 이 전력 소자는 게이트, 드레인, 소스 단자를 갖추고 있습니다. 비편향 패키지의 경우 정확한 핀 1 방향과 풋프린트 세부 정보는 제조사 데이터시트를 참조하십시오. 일반적인 응용 분야로는 전원 공급 장치 설계, 모터 구동, 부하 스위칭이 있습니다.

PI7C9X1170ABLEX의 rectangular 패키지 핀아웃 다이어그램

다음에 대한 상세 핀아웃 데이터 없음: PI7C9X1170ABLEX.

다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.

일반적인 애플리케이션

PI7C9X1170ABLEX 적합 용도: 6 애플리케이션s: Battery-Powered Sensor Hubs, Embedded Data-Acquisition Systems, Flash-Memory Access and Configuration, Handheld Test and Measurement Instruments, Industrial Control and Peripheral Consolidation, Portable and Wearable Device Interfaces.

🧩

Battery-Powered Sensor Hubs

The PI7C9X1170ABLEX fits sensor-hub boards that collect measurements through I2C or SPI and forward them through a UART link. Its single-channel bridge architecture avoids dedicating a processor I/O port to each peripheral bus, while the eight programmable GPIO pins can handle module enables, interrupt acknowledgments, or fault flags. The manufacturer highlights low operating and sleeping current for portable systems, and the 16-TSSOP package preserves board area. Firmware should enable sleep during idle periods and reinitialize the interface after wake-up so the host and peripheral remain synchronized.

📟

Embedded Data-Acquisition Systems

In an embedded measurement system, the PI7C9X1170ABLEX can place high-speed peripheral data behind a UART transport while accepting commands from the bus side. The manufacturer specifies operation at data rates up to 33 Mbps, giving the design headroom for demanding converters and memory devices. Because the device also provides up to eight programmable GPIO pins, the same circuit can capture trigger, status, or interlock signals without expanding the host pin count. Validate the bridge timing and maximum sustained transfer rate in the target system.

🖥️

Flash-Memory Access and Configuration

The PI7C9X1170ABLEX can bridge a controller's UART commands to an I2C or SPI flash device, simplifying a design that otherwise requires a dedicated serial-memory interface. Protocol translation concentrates the flash-access sequencing in one controller, while the GPIO pins can supply a chip-select, write-protect, or fault indication where the application needs it. Designers should verify the supported SPI mode, address width, and maximum operating clock against the flash datasheet. Power-down and wake-up handling must also prevent unintended memory writes when the host resets.

🛠️

Handheld Test and Measurement Instruments

A handheld instrument often combines several serial peripherals with a UART-based host or service connector. The PI7C9X1170ABLEX consolidates that connectivity in one 16-TSSOP controller, and its manufacturer-described low sleeping current supports battery-powered operation between measurement cycles. The programmable GPIO pins can supervise instrument-ready, trigger, or charger-status signals. Designers should use the datasheet power and timing tables to select wake-up behavior and confirm that the chosen temperature grade covers the instrument's ambient range.

🏭

Industrial Control and Peripheral Consolidation

Industrial controller boards can use the PI7C9X1170ABLEX to connect an I2C or SPI peripheral bank to a UART-based service processor or remote communication module. This is useful when the main control processor has limited serial-controller resources or when a legacy UART infrastructure must retain access to modern peripherals. The bridge occupies a compact 16-TSSOP footprint, while the GPIO outputs can provide reset, alert, or channel-enable control. Industrial deployments should verify supply tolerances, temperature grade, and isolation requirements in the final system architecture.

📱

Portable and Wearable Device Interfaces

The PI7C9X1170ABLEX is suitable for portable products that need to bridge compact sensors or radio-support components into a UART stream. Its small TSSOP package, up to 33 Mbps serial capability, and low operating and sleeping current suit area- and power-constrained designs. Up to eight programmable GPIO pins can be assigned to motion wake-up, strap selection, or peripheral status functions. The bridge should be placed near the serial devices it serves to keep clock and data traces short, while UART routing should avoid noisy switching-converter regions.

What is the PI7C9X1170ABLEX?
The PI7C9X1170ABLEX is a Diodes Incorporated single-channel bridge controller that converts between an I2C-bus or SPI interface and a UART interface. According to the manufacturer datasheet, it supports data rates up to 33 Mbps and includes up to eight programmable GPIO pins. The device is offered in a 16-pin TSSOP package for compact embedded and cost-sensitive designs.
What is the maximum data rate of the PI7C9X1170ABLEX?
The PI7C9X1170ABLEX supports data rates up to 33 Mbps, as stated in the manufacturer datasheet description. This rate describes the high-performance serial capability of the bridge rather than a guaranteed UART throughput for every protocol combination. Check the clocking, divider, and framing configuration in the datasheet before committing the interface to a specific baud-rate plan.
Where can I download the PI7C9X1170ABLEX datasheet PDF?
The official PI7C9X1170 datasheet PDF is available from Diodes Incorporated at https://www.diodes.com/datasheet/download/PI7C9X1170.pdf. Use the pin-description table, electrical characteristics, timing diagrams, and configuration sections for layout and firmware work. Distributor listings also identify the device as an I2C/SPI to single-UART bridge in a 16-pin TSSOP package.
How many GPIO pins does the PI7C9X1170ABLEX provide?
The PI7C9X1170ABLEX provides up to eight additional programmable general-purpose I/O pins. These pins can be assigned for control, status, interrupt, or sideband functions while the serial bridge handles the primary data path. Confirm the available pin count and multiplexing restrictions against the specific package pinout because not every configuration may expose all eight functions simultaneously.
What package does the PI7C9X1170ABLEX use?
The PI7C9X1170ABLEX is listed in a 16-pin TSSOP package with gull-wing leads and a rectangular body. The manufacturer describes the device as a very small package suited to handheld and battery-powered equipment. Use the package drawing and land pattern in the manufacturer datasheet when defining the PCB footprint and solder-mask clearance.
Is the PI7C9X1170ABLEX pin compatible with PI7C9X1170ABLE?
The PI7C9X1170ABLE and PI7C9X1170ABLEX are closely related Diodes Incorporated entries listed with the same 16-TSSOP I2C/SPI-to-UART bridge designation. Their exact ordering-code differences and pin compatibility should be checked against the ordering-information section of the PI7C9X1170 datasheet. Treat the base part as a conditional replacement only after confirming temperature grade, packing code, and exposed-pad requirements.
Is PI7C9X1170BBLEX a drop-in replacement for PI7C9X1170ABLEX?
PI7C9X1170BBLEX is a related Diodes Incorporated member of the PI7C9X1170 family, but the cross-reference listing alone does not establish exact pin and parameter equivalence with PI7C9X1170ABLEX. Compare the ordering codes, package dimensions, GPIO configuration, protocol support, and electrical limits in the PI7C9X1170 datasheet before treating it as a drop-in replacement.
When should I choose PI7C9X1170ABLEX instead of PI7C9X1170BBLEX?
Choose PI7C9X1170ABLEX when the ordering information for that exact suffix matches the required grade, protocol set, GPIO arrangement, and package. Choose PI7C9X1170BBLEX only when its manufacturer-specific configuration also satisfies those conditions. Because suffix differences can encode functional or qualification changes, the PI7C9X1170 datasheet ordering table is the controlling document for final sourcing decisions.
Can PI7C9X1170ABLEX replace a UART bridge with discrete logic?
Yes, the PI7C9X1170ABLEX can replace discrete interface logic when the system needs a supported I2C or SPI source, a UART destination, and deterministic protocol translation. The integration reduces firmware and board area while providing up to eight programmable GPIO pins and a maximum rated data rate of 33 Mbps. Validate framing, timing, fault behavior, and level compatibility before replacing a proven implementation.
What are the key specifications of PI7C9X1170ABLEX that engineers should know?
The key PI7C9X1170ABLEX specifications are single-channel UART bridging, I2C-bus or SPI source support, a data rate up to 33 Mbps, up to eight programmable GPIO pins, and a 16-pin TSSOP package. The manufacturer datasheet also describes low operating and sleeping current for portable applications. Supply limits, exact current figures, and timing values should be taken from the electrical-characteristics tables.
What can replace the PI7C9X1170ABLEX?
PI7C9X1170ABLE is the closest related ordering entry identified for the same family and 16-TSSOP bridge category, while PI7C9X1170BBLEX is another family member. Neither relationship should be treated as an automatic drop-in replacement until the ordering table confirms identical pinout and functionality. Request the current availability and quotation for the exact MPN through the Request a Quote form on this page.
Is there a Diodes Incorporated equivalent for the PI7C9X1170ABLEX?
No separate cross-manufacturer equivalent is established by the manufacturer cross-reference results for this MPN. The verified candidates are other Diodes Incorporated PI7C9X1170 family entries, including PI7C9X1170ABLE and PI7C9X1170BBLEX. Because protocol behavior and ordering-code details must match, qualify the selected family member against the original datasheet rather than choosing on package name alone.
Is the PI7C9X1170ABLEX suitable for battery-powered devices?
The PI7C9X1170ABLEX is suitable for many battery-powered devices because the manufacturer explicitly highlights low operating and sleeping current and a compact package. Use the sleeping mode in designs where the UART host can tolerate periodic wake-up and reinitialization. Exact current budgets must be calculated from the electrical characteristics for the selected clock and operating configuration.
Where can I find the PI7C9X1170ABLEX pinout?
The PI7C9X1170ABLEX pinout is documented in the pin-description and package-outline sections of the official PI7C9X1170 datasheet. The verified distributor listings identify the target as a 16-TSSOP device, but the public listing text does not enumerate every signal name. Use the datasheet pin table to assign supply, ground, clock, serial-data, UART, and GPIO connections during schematic capture.
How do I buy PI7C9X1170ABLEX online and check availability?
Use the Request a Quote form on this page to request current availability, lead time, and a quotation for PI7C9X1170ABLEX. The manufacturer datasheet and distributor catalog pages identify the part as a 16-pin TSSOP I2C/SPI-to-UART bridge controller. Because availability and delivery schedules can change by region and order quantity, submit the exact MPN and required quantity through that form.

엔지니어링 참조 데이터: PI7C9X1170ABLEX — 비교, 설계 지침 및 규정 준수 정보.

선택 가이드

Choose the PI7C9X1170ABLEX when a design needs to connect an I2C or SPI peripheral to a UART host and benefits from a compact 16-TSSOP implementation with up to eight programmable GPIO pins. Its manufacturer-stated data-rate capability reaches 33 Mbps, and the family's low operating and sleeping current suit portable equipment. Consider PI7C9X1170ABLE when its ordering suffix provides the required grade or packing arrangement and the pin configuration is confirmed identical. Consider PI7C9X1170BBLEX only after checking the PI7C9X1170 ordering table for functional and qualification differences. For designs requiring another UART channel, different electrical limits, or another package, use a bridge with matching channel count and pinout rather than forcing a suffix change. Firmware qualification should cover protocol conversion, clocking, sleep and wake behavior, GPIO multiplexing, and fault recovery before production release.

대체품과의 비교

파라미터 이 제품 PI7C9X1170ABLE PI7C9X1170BBLEX
Brand Diodes Incorporated Diodes Incorporated Diodes Incorporated
Package 16-TSSOP 16-TSSOP 16-TSSOP
Mounting Type Surface mount Surface mount Surface mount

주요 차별점

  • Single-chip protocol translation with programmable sideband control (vs PI7C9X1170BBLEX)
  • High-speed serial performance in a compact package (vs PI7C9X1170ABLE)
  • Designed for portable power constraints (vs PI7C9X1170BBLEX)

설계 노트

Place the PI7C9X1170ABLEX close to the I2C or SPI peripheral it serves and route the UART interface toward the host connector. Keep serial clock and data traces short, avoid stubs, and maintain a continuous ground reference beneath the signal paths. The eight GPIO lines should also be routed away from high-voltage switching nodes, especially when the bridge is used near an RF or power-conversion section.

Decouple the device at its supply pins with the capacitance specified by the manufacturer datasheet and place it close to the package power and ground connections. Review operating and sleeping current in the selected clock configuration rather than estimating from the headline data-rate rating. For battery-powered equipment, define a deterministic wake sequence that prevents bus traffic before the peripheral and bridge clocks are stable.

Treat the I2C or SPI clock as a critical timing signal and verify pull-up values, bus capacitance, rise time, and the maximum supported clock in the datasheet. UART signals crossing between domains may require level translation if the bridge and host use different logic standards. Confirm whether signals are driven during sleep so that a partially powered peripheral cannot receive corrupted commands.

Do not select a family member solely because it has the same package outline. Ordering suffixes can identify different grades, packing arrangements, or configurations, so verify the PI7C9X1170 ordering table before substitution. Also validate the device's framing, GPIO multiplexing, and firmware configuration; a pin-compatible package does not by itself guarantee identical peripheral behavior.

규정 준수 정보

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
무연
Unknown
무할로겐
Unknown
분쟁 광물
Unknown

The industrial temperature grade is identified in the catalog listing. Compliance declarations are not stated in the verified excerpts and remain unconfirmed.

관련 검색

PI7C9X1170ABLEX datasheet PI7C9X1170ABLEX datasheet pdf PI7C9X1170ABLEX pinout PI7C9X1170ABLEX equivalent PI7C9X1170ABLEX replacement PI7C9X1170ABLEX price PI7C9X1170ABLEX stock PI7C9X1170 I2C SPI UART bridge PI7C9X1170 33 Mbps UART PI7C9X1170ABLEX vs PI7C9X1170BBLEX 16-TSSOP I2C to UART bridge PI7C9X1170ABLEX application circuit Diodes Incorporated PI7C9X1170ABLEX

관련 부품 & 용어

Diodes Incorporated PI7C9X1170ABLEX PI7C9X1170ABLE PI7C9X1170BBLEX PI7C9X1170 I2C bridge SPI-to-UART bridge UART interface controller serial interface IC programmable GPIO 33 Mbps data rate 16-TSSOP thin shrink small outline package surface-mount semiconductor industrial temperature grade battery-powered device sensor hub embedded data acquisition flash-memory interface serial protocol translation low operating current sleeping current
빠른 견적 RFQ
상세 정보를 모두 입력하십시오 — 영업팀이 24시간 이내에 답변드립니다
부품 번호 제조사 패키지 QTY 목표 가격 합계
✓
견적이 제출되었습니다!

24시간 이내에 이메일로 답변드리겠습니다

1
RFQ 제출됨
2
견적 접수됨
3
주문 완료
4
결제
5
배송됨
6
배송 완료
RFQ 상세 보기