Diodes Incorporated

PI7C9X1170CZDEX I2C/SPI to UART Bridge | Diodes

N.º de pieza: PI7C9X1170CZDEX ✓ Activo
24-pin TQFN Package
MOQ: 1 |

PI7C9X1170CZDEX Descripción general

Diodes Incorporated PI7C9X1170CZDEX is an I2C/SPI-to-UART interface bridge with 24 pins in a 4 x 4 mm TQFN package. It provides a translation layer between serial bus interfaces and a UART interface, allowing equipment with an I2C or SPI host to communicate with a UART-based peripheral. The device is intended for compact embedded and control systems where a standardized serial bridge is preferable to implementing the protocol conversion in software.

An interface bridge is a semiconductor that translates the signaling and transaction format of one communication interface into that of another. In the system hierarchy, the PI7C9X1170 belongs to interface ICs, serial interface controllers, and protocol converters. It sits between a host controller and a UART peripheral, reducing the need for host software to emulate the remote protocol while preserving a conventional serial connection at the other side of the link.

The PI7C9X1170CZDEX uses two-wire I2C signaling with serial data on SDA and serial clock on SCL. According to the manufacturer datasheet, the I2C interface supports Standard-mode and Fast-mode I2C-bus operation. The same device also provides an SPI interface for host-side communication, giving the system designer two possible host-bus paths while presenting a UART interface to the target peripheral.

The 24-TQFN package measures 4 x 4 mm and supports compact surface-mount assembly. Its leadless construction reduces the PCB footprint compared with larger leaded interface packages, although exposed-pad thermal management and assembly process controls remain important. The CZDEX ordering code is associated with tape-and-reel production packaging, and distributor product information identifies a standard quantity of 3,500 units.

Typical uses include industrial control modules, programmable logic controllers, embedded test equipment, communication adapters, and peripheral boards that need to bridge a host-controller bus to a UART device. The bridge can simplify hardware partitioning when the UART endpoint is already available and the host operates through I2C or SPI. System compatibility still depends on the device-specific commands, electrical levels, signal mapping, and timing configuration described in the manufacturer documentation.

PCB planning should follow the manufacturer pin-description and layout guidance, particularly for power, ground, I2C pull-up requirements, and the exposed thermal pad. Confirm the exact pin functions and package drawing before routing. Do not assume that every I2C or SPI peripheral can be connected without checking the bridge's supported command set and electrical interface requirements.

This page organizes the PI7C9X1170CZDEX interface details, verified package information, sourcing workflow, and practical implementation guidance. It also separates confirmed manufacturer characteristics from electrical parameters that require confirmation from the datasheet, helping engineers move from component selection to a careful hardware review.

Alternativas directas para PI7C9X1170CZDEX — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.

No hay alternativas directas disponibles para este producto.

Solicitar alternativas

PI7C9X1170CZDEX Valores máximos y características eléctricas

Product Type I2C/SPI-to-UART interface bridge
Host Interfaces I2C and SPI
Peripheral Interface UART
I2C Compliance Standard-mode and Fast-mode I2C-bus specifications
I2C Signal Lines 2 lines: SDA and SCL
Package Type 24-pin TQFN
Package Dimensions 4 x 4 mm
Total Pins 24 pins
Tipo de montaje Surface mount
Shipping Package Tape and reel
Standard Packaging Quantity 3,500 units

Guía de configuración de pines de PI7C9X1170CZDEX tape and reel

Configuración de pines para PI7C9X1170CZDEX (encapsulado tape and reel). Este dispositivo de potencia presenta terminales de puerta, drenador y fuente. Para encapsulados no polarizados, consulte la hoja de datos del fabricante para conocer la orientación exacta del pin 1 y los detalles del footprint. Las aplicaciones habituales incluyen el diseño de fuentes de alimentación, el accionamiento de motores y la conmutación de cargas.

Diagrama de patillaje del encapsulado tape and reel para PI7C9X1170CZDEX

No hay datos detallados de patillaje disponibles para PI7C9X1170CZDEX.

Consulte la hoja de datos para ver la configuración completa de patillas.

Aplicaciones típicas

PI7C9X1170CZDEX es adecuado para 6 aplicacións: Industrial Control Module, Programmable Logic Controller, Communication Adapter, Embedded Test Equipment, Programmable Peripheral Board, Portable Instrumentation Interface.

🏭

Industrial Control Module

The PI7C9X1170CZDEX fits industrial control modules that use a host processor for supervisory functions while retaining a UART-based local peripheral. Place the bridge between the controller's I2C or SPI bus and the UART endpoint so the main processor can exchange commands without implementing a complete UART protocol state machine. Its Standard-mode and Fast-mode I2C support provides defined host-side operating options. The 4 x 4 mm TQFN package also preserves board area in densely populated control hardware. Before layout release, verify the required UART signal mapping, supported device commands, logic levels, and exposed-pad connection from the manufacturer datasheet.

⚡

Programmable Logic Controller

The PI7C9X1170CZDEX is applicable in programmable logic controller designs where the main controller uses I2C or SPI but an expansion module retains a conventional UART connection. The dedicated bridge provides a defined translation path from the host interface to the UART peripheral, reducing the protocol logic burden placed on the main processor. This can simplify firmware partitioning while retaining a recognizable host-to-peripheral architecture. The 24-pin TQFN construction supports compact control boards, although exposed-pad routing and manufacturing controls must follow the package drawing. Confirm register behavior, timing, supply requirements, and UART configuration before integrating it into a safety- or production-critical controller.

🌐

Communication Adapter

The PI7C9X1170CZDEX can serve as the protocol-conversion element in a communication adapter that accepts commands through I2C or SPI and forwards them to a UART-connected module. This arrangement is useful when the adapter's host already has a bus-oriented processor interface but the remote module exposes only a serial UART port. The bridge's two-wire I2C path uses SDA and SCL, with Standard-mode and Fast-mode operation specified by the manufacturer. Its compact 4 x 4 mm TQFN package allows the adapter to remain compact. Designers should still validate address handling, command support, UART baud configuration, signal levels, and timing against the device documentation before field deployment.

🔧

Embedded Test Equipment

The PI7C9X1170CZDEX fits embedded test and measurement equipment where a controller needs to access a UART-based instrument or peripheral through I2C or SPI. The dedicated bridge allows the instrument interface to remain UART while the control plane uses the processor's preferred bus. This can make the test fixture easier to standardize and reduce repetitive low-level protocol handling in the main controller firmware. The 24-pin surface-mount package supports compact instrument electronics, and the manufacturer's stated I2C support includes Standard-mode and Fast-mode operation. Confirm the supported command subset, timing limits, electrical levels, and exposed-pad layout before integrating the device into automated test systems.

🧩

Programmable Peripheral Board

The PI7C9X1170CZDEX is appropriate for programmable peripheral boards that expose an I2C or SPI host interface while retaining UART connectivity to an established subsystem. A system designer can isolate the UART protocol behavior behind the bridge, allowing the host controller to focus on measurement, control, or user-interface functions. The compact 24-pin TQFN package limits the footprint required for this interface translation. For reliable deployment, review the manufacturer's pin description, supported bus modes, and timing requirements, and ensure that the PCB provides the required power, ground, pull-up, and thermal-pad connections. Validate the complete command exchange with the intended peripheral before production.

📱

Portable Instrumentation Interface

The PI7C9X1170CZDEX can support portable instrumentation interfaces where limited board area makes a dedicated serial bridge attractive. A portable controller using I2C or SPI can communicate with a UART-based sensor, logger, or service module through the 4 x 4 mm TQFN bridge. The device's two-wire I2C path and documented Standard-mode and Fast-mode compliance help establish a predictable host connection, while the alternate SPI path gives designers another integration option. The package saves space compared with a conventional leaded bridge. Before finalizing a portable design, confirm supply voltage, operating temperature, signal-level compatibility, UART behavior, and thermal management, since those qualifications are essential for reliable field operation.

What is the PI7C9X1170CZDEX?
The PI7C9X1170CZDEX is a 24-pin I2C/SPI-to-UART interface bridge from Diodes Incorporated. According to the manufacturer datasheet, it supports Standard-mode and Fast-mode I2C communication through the SDA and SCL lines while providing a bridge to a UART peripheral. The device is packaged in a compact 4 x 4 mm TQFN package for surface-mount embedded systems.
Which interfaces does the PI7C9X1170CZDEX support?
The PI7C9X1170CZDEX supports I2C and SPI on the host side and UART on the peripheral side. The manufacturer datasheet identifies the I2C path as two lines, serial data on SDA and serial clock on SCL, and states that the interface complies with Standard-mode and Fast-mode I2C-bus specifications. The 24-pin TQFN package integrates the interface-conversion functions into a 4 x 4 mm surface-mount device.
Where can I download the PI7C9X1170CZDEX datasheet PDF?
The PI7C9X1170CZDEX datasheet PDF is available through the manufacturer documentation link listed on this page. The document covers the I2C/SPI-to-UART bridge, including its SDA and SCL connections, Standard-mode and Fast-mode I2C behavior, package information, electrical characteristics, and application guidance. Use the pin-description table in that document before assigning PCB tracks or configuring a prototype.
Where can I find the PI7C9X1170CZDEX pinout?
The PI7C9X1170CZDEX pinout is defined by the pin-description table and package drawing in the manufacturer datasheet. The device has 24 pins in a 4 x 4 mm TQFN package, including the I2C SDA and SCL connections, UART signals, supply connections, ground pins, and exposed-pad considerations. Verify every net against the datasheet because exposed-pad and ground assignments must match the selected package.
Can the PI7C9X1170CZDEX replace a software-based I2C-to-UART bridge?
The PI7C9X1170CZDEX can replace a software-based protocol bridge when the host and peripheral requirements match its I2C/SPI-to-UART architecture and command set. The hardware implementation uses the 24-pin TQFN device instead of dedicating host resources to a software state machine. Verify supported registers, timing, electrical levels, and UART behavior before committing to a drop-in PCB or firmware redesign.
What is the best drop-in replacement for PI7C9X1170CZDEX?
No independently verified drop-in replacement for the PI7C9X1170CZDEX is identified by the available cross-reference results. A valid replacement must match the 24-pin TQFN footprint, preserve the I2C, SPI, and UART connections, and maintain compatible electrical and command behavior. Use the Request a Quote form on this page to discuss an exact replacement with the sourcing team rather than substituting a merely functional interface bridge.
What can replace PI7C9X1170CZDEX?
The PI7C9X1170CZDEX should be replaced only by a pin-compatible 24-pin interface bridge with equivalent I2C, SPI, and UART behavior. No verified same-package substitute appears in the available cross-reference results, so package matching and manufacturer documentation must be checked before selecting a candidate. The Request a Quote form can be used to request help identifying a suitable exact replacement.
Is the PI7C9X1170CZDEX suitable for an industrial controller?
The PI7C9X1170CZDEX is suitable for industrial-controller use when the system meets its electrical, temperature, and communication requirements. Its I2C interface supports Standard-mode and Fast-mode operation, while the SPI and UART paths support host-to-peripheral translation in a compact 24-pin TQFN package. Confirm supply voltage, operating temperature, logic levels, and supported command behavior before production release.
When should I choose the PI7C9X1170CZDEX instead of using a microcontroller UART driver?
Choose the PI7C9X1170CZDEX when a fixed I2C/SPI-to-UART protocol conversion can offload communication handling from the main processor. The dedicated bridge offers a 4 x 4 mm 24-pin package and separates the UART peripheral connection from the host bus. A software driver may be preferable when the protocol is highly customized, requires frequent host intervention, or has no matching hardware bridge.
What is the difference between I2C and SPI host operation on the PI7C9X1170CZDEX?
The PI7C9X1170CZDEX supports two host-side choices with different signal characteristics. I2C uses the two documented lines SDA and SCL and operates in Standard-mode or Fast-mode, while SPI uses a separate host interface and provides a different clock-and-data arrangement. The manufacturer datasheet defines the electrical and transaction requirements for each path.
How do PI7C9X1170CZDEX and a conventional UART transceiver differ?
The PI7C9X1170CZDEX performs protocol bridging as well as providing a UART connection, whereas a conventional UART transceiver primarily translates digital logic levels into electrical signals. Its I2C and SPI host interfaces let a controller initiate transactions without implementing the entire UART-side protocol in host software. It therefore solves a broader interface-conversion function within a 24-pin TQFN device.
Is the PI7C9X1170CZDEX in stock and what is its lead time?
Current stock and manufacturing lead time are best confirmed through the Request a Quote form on this page. Product listings state that the PI7C9X1170CZDEX is available for ordering, but live inventory, lot availability, and lead time can vary by quantity and date. Submit the required quantity, shipment location, and target schedule for a current sourcing response.
Where can I buy PI7C9X1170CZDEX online?
The PI7C9X1170CZDEX can be requested through the Request a Quote form on this page. The form is the appropriate route for current unit availability, volume pricing, scheduled delivery, and lot traceability. It avoids presenting a potentially stale inventory or pricing value as a firm quotation.
What is the price of PI7C9X1170CZDEX?
The current PI7C9X1170CZDEX price is determined by quantity, availability, and requested delivery terms through the Request a Quote form on this page. The device is ordered as a 24-pin TQFN tape-and-reel component with a stated standard packaging quantity of 3,500 units. Submit the required order quantity for an updated quote.
What are the key specifications of PI7C9X1170CZDEX that engineers should know?
The PI7C9X1170CZDEX combines I2C, SPI, and UART interfaces in a 24-pin, 4 x 4 mm surface-mount TQFN package. According to the manufacturer datasheet, its two-wire I2C interface uses SDA and SCL and complies with Standard-mode and Fast-mode specifications. The CZDEX ordering code is supplied in tape-and-reel packaging with a stated standard quantity of 3,500 units.
Does the PI7C9X1170CZDEX meet RoHS and AEC-Q100 requirements?
RoHS, REACH, and AEC-Q100 status for the PI7C9X1170CZDEX must be confirmed from the current manufacturer product documentation before a regulated production release. These compliance claims are not inferred from the package or ordering code. Request the latest declarations and qualification documentation through the Request a Quote form, especially for automotive or other regulated applications.

Datos de referencia de ingeniería para PI7C9X1170CZDEX — comparación, orientación de diseño e información de cumplimiento.

Guía de selección

Choose the PI7C9X1170CZDEX when a compact system needs a dedicated interface bridge between an I2C or SPI host and a UART peripheral. Its two-wire SDA/SCL interface, documented Standard-mode and Fast-mode support, and 24-pin 4 x 4 mm TQFN package are well suited to embedded controllers and communication adapters. Select a software UART implementation instead when the protocol changes frequently, requires direct host intervention, or cannot be represented by the bridge's supported command behavior. Choose another IC only after verifying exact 24-pin footprint compatibility, I2C/SPI/UART electrical requirements, timing, and command semantics. The absence of a verified drop-in substitute means that a redesign candidate should not be treated as interchangeable without a complete manufacturer-level pin and functional comparison.

Comparación con alternativas

Parámetro Este producto
Package 24-pin TQFN (4 x 4 mm)
Brand Diodes Incorporated
Device Type I2C/SPI-to-UART interface bridge
Host Interfaces I2C and SPI
Peripheral Interface UART
I2C Mode Support Standard-mode and Fast-mode
I2C Signal Lines 2 lines: SDA and SCL
Total Pins 24 pins
Package Dimensions 4 x 4 mm
Shipping Package Tape and reel
Standard Packaging Quantity 3,500 units

Diferenciadores clave

  • Three-interface integration in one bridge (frente a Conventional two-wire UART transceiver)
  • Documented Standard-mode and Fast-mode I2C support (frente a Single-mode I2C interface bridge)
  • Compact 24-pin TQFN implementation (frente a Lead-interface bridge in a larger package)

Notas de diseño

Route SDA and SCL as short, compact traces and place any required pull-up resistors close to the bus master or the appropriate bus endpoint. Keep the bridge's ground and supply connections close to their pins, and connect the TQFN exposed pad according to the manufacturer layout guidance. Do not assign the pin functions until the complete 24-pin description and package drawing have been cross-checked.

Treat the exposed thermal pad as both a thermal and electrical structure. Follow the datasheet's recommended pad geometry, via arrangement, solder-mask policy, and copper connection. A 4 x 4 mm TQFN leaves limited room around the perimeter, so placing bypass capacitors and pull-up networks requires coordination with the pinout. Review assembly drawings to avoid conflicts between exposed-pad vias and no-stencil regions.

Do not assume that any UART peripheral can be substituted for the supported endpoint without checking protocol, register, baud-rate, framing, and electrical-level requirements. Standard-mode and Fast-mode descriptions apply to the I2C side and do not by themselves guarantee every timing condition of the overall design. Validate startup behavior, bus contention, communication errors, and the manufacturer's recommended decoupling before releasing a production layout.

Información de cumplimiento

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Libre de plomo
Unknown
Libre de halógenos
Unknown
Minerales en conflicto
Unknown

Current compliance declarations were not identified in the manufacturer or distributor information for this listing. Confirm RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status with the manufacturer before production release.

Datos verificados el: 2026-11-17 — datos verificados y seleccionados por el equipo de ingeniería de componentes de XAIPART

Búsquedas relacionadas

PI7C9X1170CZDEX datasheet PI7C9X1170CZDEX datasheet pdf PI7C9X1170CZDEX pinout PI7C9X1170CZDEX equivalent PI7C9X1170CZDEX replacement PI7C9X1170CZDEX price PI7C9X1170CZDEX stock Diodes PI7C9X1170CZDEX PI7C9X1170 I2C SPI UART bridge PI7C9X1170 24 TQFN 4x4 PI7C9X1170 application circuit PI7C9X1170 cross reference

Componentes & términos relacionados

Diodes Incorporated PI7C9X1170CZDEX PI7C9X1170 I2C SPI UART interface bridge protocol converter Interface ICs serial interface controller embedded control system SDA SCL Standard-mode I2C Fast-mode I2C 24-pin TQFN 4 x 4 mm package surface-mount package exposed pad industrial control programmable logic controller communication adapter test equipment tape and reel
RFQ de presupuesto rápido
Complete los detalles — nuestro equipo de ventas responderá en un plazo de 24 horas
Número de pieza Fabricante Encapsulado QTY Precio objetivo Total
✓
¡Presupuesto enviado!

Responderemos a su correo electrónico en un plazo de 24 horas

1
RFQ enviado
2
Presupuesto recibido
3
Pedido realizado
4
Pago
5
Enviado
6
Entregado
Ver detalles del RFQ