PI7C9X760CZDE - 33Mbps I2C/SPI to UART Bridge | Diodes
N.º de pieza: PI7C9X760CZDE ✗ Fin de vidaPI7C9X760CZDE Descripción general
An interface bridge converts data between serial protocols that use different signaling structures and transaction formats. In this case, the PI7C9X760 family provides an I2C-bus or SPI controller on one side and a UART interface on the other. This bridge category sits within interface ICs and semiconductor solutions that connect embedded processors, peripherals, sensors, and communications equipment without requiring the host controller to implement every serial protocol directly.
The controller combines a maximum 33 Mbps data rate with low operating and sleeping current, making it suitable for compact and power-conscious equipment. Its eight programmable GPIO pins allow additional digital functions to share the same package footprint. The small 4 x 4 mm VQFN-24 package is particularly useful where board area is constrained, while the single-channel architecture targets designs requiring one dedicated UART bridge channel.
The PI7C9X760 architecture supports flexible serial-side selection between I2C-bus and SPI connections while presenting a UART interface to the remote endpoint. Its 64-byte transmit and receive FIFOs help buffer traffic between the host-side serial transaction and the UART stream, reducing the amount of data that must be handled synchronously by the controller. The exact register behavior, clocking requirements, and operating modes should be configured from the manufacturer datasheet.
Typical uses include handheld and battery-operated instruments, industrial serial adapters, embedded data-acquisition equipment, sensor-control systems, and portable accessories that must translate between a host processor's I2C or SPI bus and a UART peripheral. The same package can also support compact communications modules in which a low-pin-count embedded controller provides the higher-level protocol functions.
When laying out a board, place input and output decoupling capacitors close to their designated power pins, route high-speed serial signals over short and continuous reference planes, and keep the exposed pad thermally coupled to a properly sized ground pour. Confirm pin multiplexing, signal levels, voltage tolerances, clock sources, and reset requirements against the PI7C9X760 datasheet before releasing production artwork.
This product page combines the manufacturer datasheet information with practical protocol, layout, and sourcing guidance. It identifies the PI7C9X760CZDE's verified 33 Mbps capability, 24-pin VQFN-24 construction, FIFO capacity, and GPIO resources while clearly separating confirmed characteristics from design values that still require circuit-specific validation.
Alternativas directas para PI7C9X760CZDE — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con PI7C9X760CZDE (mismo factor de forma y huella) — difiere en Maximum Data Rate, Package, REACH Status.
PI7C9X760CZDEX
✅ Sustitución directaConsulte el precio
Ver hoja de datos →PI7C9X760CZDE Valores máximos y características eléctricas
| Product Type | I2C-bus/SPI to single-channel UART bridge controller |
| Manufacturer | Diodes Incorporated |
| Maximum Data Rate | 33 Mbps |
| UART Channels | 1 channel |
| Host-Side Interfaces | I2C-bus and SPI |
| Remote-Side Interface | UART |
| Transmit FIFO Capacity | 64 bytes |
| Receive FIFO Capacity | 64 bytes |
| Programmable GPIO Count | 8 pins |
| Encapsulado | 24-pin VQFN, 4 mm x 4 mm |
| Tipo de montaje | Surface mount |
| Shipping Format | Tray |
| Tray Quantity | 490 pieces |
| Estado RoHS | unknown |
| REACH Status | unknown |
| Lead-Free Status | unknown |
Guía de configuración de pines de PI7C9X760CZDE 24-pin vqfn, 4 mm x 4 mm
Configuración de pines para PI7C9X760CZDE (encapsulado 24-pin vqfn, 4 mm x 4 mm). Este dispositivo de potencia presenta terminales de puerta, drenador y fuente. Para encapsulados no polarizados, consulte la hoja de datos del fabricante para conocer la orientación exacta del pin 1 y los detalles del footprint. Las aplicaciones habituales incluyen el diseño de fuentes de alimentación, el accionamiento de motores y la conmutación de cargas.
No hay datos detallados de patillaje disponibles para PI7C9X760CZDE.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
PI7C9X760CZDE es adecuado para 6 aplicacións: Handheld Serial Instruments, Industrial Serial Adapters, Sensor Control Systems, Embedded Data Acquisition, Battery-Powered Field Equipment, Portable Communications Modules.
Handheld Serial Instruments
The PI7C9X760CZDE fits handheld instruments in which a low-power host processor uses I2C-bus or SPI while an internal module communicates through UART. Its maximum 33 Mbps data rate supports high-throughput serial transfers, while the 64-byte transmit and receive FIFOs help buffer traffic between differently timed bus transactions and the continuous UART stream. The 4 x 4 mm VQFN-24 package preserves board area in compact products, and the manufacturer's identification of low operating and sleeping current supports battery-conscious designs. Firmware should define transaction boundaries, UART baud rate, and error recovery before production testing.
Recomendado
Industrial Serial Adapters
The PI7C9X760CZDE can serve as the protocol-conversion element in a compact industrial serial adapter. A supervisory processor may manage configuration through I2C-bus or SPI while the bridge handles a UART connection to a downstream instrument or controller. The single-channel UART architecture avoids unnecessary parallel channels, and the 33 Mbps maximum rate accommodates high-speed data transfer. Eight programmable GPIO pins can support auxiliary status, control, or interrupt signaling. A production design must separately verify industrial temperature requirements, grounding, isolation, surge protection, and electromagnetic compatibility.
Recomendado
Sensor Control Systems
The PI7C9X760CZDE is suitable for sensor-control assemblies where a controller gathers data through I2C-bus or SPI but must forward commands or results to a UART-connected sensor head. The 64-byte transmit and receive FIFOs provide buffering between short host-side transactions and the serialized UART data path, while the eight GPIO pins can support sensor-enable, fault, or interrupt functions. Its small 4 x 4 mm VQFN-24 footprint limits board-space impact in distributed sensing equipment. Designers should validate timing margins, interrupt latency, and bus isolation for the deployed cable length.
Recomendado
Embedded Data Acquisition
The PI7C9X760CZDE can be used in embedded data-acquisition systems that standardize configuration traffic over I2C-bus or SPI while transferring measurement data through UART. The controller supports rates up to 33 Mbps, allowing the UART link to carry high-volume samples when the host-side interface remains organized in discrete transactions. Separate 64-byte transmit and receive FIFOs help absorb scheduling differences between the processor and peripheral. The eight programmable GPIO pins can indicate acquisition state or trigger downstream equipment. Firmware must define framing, checksums, overrun handling, and recovery behavior for uninterrupted laboratory or field operation.
Recomendado
Battery-Powered Field Equipment
The PI7C9X760CZDE is appropriate for battery-powered field equipment that needs a UART peripheral while conserving host-controller resources. The manufacturer PI7C9X760 datasheet identifies low operating and sleeping current, and the device provides up to eight programmable GPIO pins for compact auxiliary control functions. Its 33 Mbps maximum data rate permits short, high-speed exchanges, while the 64-byte FIFOs can reduce host-side servicing overhead. To calculate system-level battery impact, engineers should combine the device's operating and sleeping current with supply voltage, wake interval, UART activity, and the power characteristics of the attached peripherals.
Recomendado
Portable Communications Modules
The PI7C9X760CZDE fits portable communications modules that expose an I2C-bus or SPI configuration interface to a host processor and use UART for an internal or external link. Its small 24-pin VQFN package measures 4 mm on each side, making it useful in space-constrained radio, accessory, and wearable-adjacent products. The maximum 33 Mbps rate and bidirectional FIFOs support rapid command and data transfer, while the GPIO pins can carry module-state signals. The final design should budget connector space, UART grounding, signal integrity, and low-power behavior rather than treating the bridge as a substitute for RF front-end functions.
Recomendado
Datos de referencia de ingeniería para PI7C9X760CZDE — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto |
|---|---|
| Manufacturer | Diodes Incorporated |
| Package | 24-pin VQFN, 4 mm x 4 mm |
| Product Type | I2C-bus/SPI to single-channel UART bridge controller |
| Maximum Data Rate | 33 Mbps |
| UART Channels | 1 channel |
| Transmit FIFO | 64 bytes |
| Receive FIFO | 64 bytes |
| Programmable GPIO | Up to 8 pins |
| Shipping Format | Tray, 490 pieces |
Diferenciadores clave
- High-speed protocol conversion in a compact package (frente a Firmware-based I2C/SPI-to-UART conversion)
- Bidirectional buffering for host-to-UART traffic (frente a Directly connected UART peripheral without a bridge)
- Auxiliary digital control without expanding the package (frente a A bridge using separate GPIO devices)
Notas de diseño
Treat the 24-pin VQFN as a high-speed mixed-signal layout problem. Place all required bypass capacitors immediately beside their associated supply and ground pins, connect the exposed pad to the appropriate ground plane with minimal via impedance, and provide uninterrupted return paths beneath serial traces. Keep I2C, SPI, and UART routes away from noisy power-conversion nodes and verify edge-rate-dependent crosstalk during prototype testing.
Configure signal levels, termination, and trace geometry from the actual clock, baud rate, and topology rather than from the 33 Mbps headline rate alone. Use continuous reference planes, avoid unnecessary stubs, and control impedance on long interconnects. For I2C-bus lines, verify pull-up voltage, capacitance, rise time, and the complete bus network; for SPI, check source-synchronous timing and return-path continuity across both chip-select and clock signals.
Do not assume that a similar PI7C9X760 packaging suffix is electrically and logistically interchangeable without checking the manufacturer ordering table. In particular, confirm that the CZDE tray version matches the required pinout, grade, quantity, and assembly process. During bring-up, test reset, clock startup, busy conditions, FIFO overflow, malformed frames, and recovery from an interrupted UART transaction so host firmware does not leave the bridge in an indeterminate state.
The 4 x 4 mm VQFN-24 package requires an exposed-pad-aware PCB footprint and adequate copper for heat spreading. Follow the manufacturer land pattern and solder-mask and paste recommendations rather than substituting a generic 24-pin footprint. Use the package thermal information and actual switching activity in the final thermal assessment, and inspect exposed-pad solder fill after assembly because an inadequate void pattern can materially increase junction temperature.
Información de cumplimiento
No explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals statement was identified for this exact ordering code. AEC-Q100 qualification does not apply because this is an interface bridge controller rather than an automotive-qualified device.