Diodes Incorporated

PI7C9X760CZDE - 33Mbps I2C/SPI to UART Bridge | Diodes

MPN: PI7C9X760CZDE ✗ Cuối đời
24-pin VQFN, 4 mm x 4 mm Package
MOQ: 1 |

PI7C9X760CZDE Tóm tắt

The Diodes Incorporated PI7C9X760CZDE is a single-channel I2C-bus/SPI to high-performance UART bridge controller with data rates up to 33 Mbps. The device is supplied in a 24-pin VQFN package measuring 4 mm by 4 mm and provides up to eight additional programmable general-purpose I/O pins. It also includes 64-byte transmit and receive FIFOs according to the PI7C9X760 datasheet description.

An interface bridge converts data between serial protocols that use different signaling structures and transaction formats. In this case, the PI7C9X760 family provides an I2C-bus or SPI controller on one side and a UART interface on the other. This bridge category sits within interface ICs and semiconductor solutions that connect embedded processors, peripherals, sensors, and communications equipment without requiring the host controller to implement every serial protocol directly.

The controller combines a maximum 33 Mbps data rate with low operating and sleeping current, making it suitable for compact and power-conscious equipment. Its eight programmable GPIO pins allow additional digital functions to share the same package footprint. The small 4 x 4 mm VQFN-24 package is particularly useful where board area is constrained, while the single-channel architecture targets designs requiring one dedicated UART bridge channel.

The PI7C9X760 architecture supports flexible serial-side selection between I2C-bus and SPI connections while presenting a UART interface to the remote endpoint. Its 64-byte transmit and receive FIFOs help buffer traffic between the host-side serial transaction and the UART stream, reducing the amount of data that must be handled synchronously by the controller. The exact register behavior, clocking requirements, and operating modes should be configured from the manufacturer datasheet.

Typical uses include handheld and battery-operated instruments, industrial serial adapters, embedded data-acquisition equipment, sensor-control systems, and portable accessories that must translate between a host processor's I2C or SPI bus and a UART peripheral. The same package can also support compact communications modules in which a low-pin-count embedded controller provides the higher-level protocol functions.

When laying out a board, place input and output decoupling capacitors close to their designated power pins, route high-speed serial signals over short and continuous reference planes, and keep the exposed pad thermally coupled to a properly sized ground pour. Confirm pin multiplexing, signal levels, voltage tolerances, clock sources, and reset requirements against the PI7C9X760 datasheet before releasing production artwork.

This product page combines the manufacturer datasheet information with practical protocol, layout, and sourcing guidance. It identifies the PI7C9X760CZDE's verified 33 Mbps capability, 24-pin VQFN-24 construction, FIFO capacity, and GPIO resources while clearly separating confirmed characteristics from design values that still require circuit-specific validation.

Bộ thay thế dễ dàng lắp đặt cho PI7C9X760CZDE — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.

Các biến thể trong loạt này

Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với PI7C9X760CZDE (cùng hình factor và footprint) — khác nhau ở Maximum Data Rate, Package, REACH Status.

Diodes Incorporated
Maximum Data Rate: 33Mbps
Package: 24-TQFN (4x4 mm)
REACH Status: REACH unaffected
So sánh với PI7C9X760CZDE →

PI7C9X760CZDEX

✅ Drop-In
Diodes Incorporated
📦 24-TQFN (4x4)
I2C-bus/SPI to single-channel UART bridge controller · 33Mbps · I2C-bus and SPI · 1 channel · 64 bytes · 8 pins · 1.62V to 3.63V · -40°C to +85°C

Liên hệ để biết giá

Xem tài liệu →

PI7C9X760CZDE Tỷ lệ tối đa & tính chất điện

Product Type I2C-bus/SPI to single-channel UART bridge controller
Manufacturer Diodes Incorporated
Maximum Data Rate 33 Mbps
UART Channels 1 channel
Host-Side Interfaces I2C-bus and SPI
Remote-Side Interface UART
Transmit FIFO Capacity 64 bytes
Receive FIFO Capacity 64 bytes
Programmable GPIO Count 8 pins
Hộp 24-pin VQFN, 4 mm x 4 mm
Kiểu lắp đặt Surface mount
Shipping Format Tray
Tray Quantity 490 pieces
Trạng thái RoHS unknown
REACH Status unknown
Lead-Free Status unknown

Hướng dẫn cấu hình chân PI7C9X760CZDE 24-pin vqfn, 4 mm x 4 mm

Cấu hình chân cho PI7C9X760CZDE (24-pin vqfn, 4 mm x 4 mm gói). Động cơ điện này có chân cổng, nguồn và đầu ra. Đối với các gói không phân極, tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết hướng dẫn chính xác của chân 1 và chi tiết về vân footprint. Các ứng dụng phổ biến bao gồm thiết kế nguồn cung cấp điện, điều khiển động cơ và chuyển đổi tải.

Bảng cấu hình chân 24-pin vqfn, 4 mm x 4 mm cho PI7C9X760CZDE

Không có dữ liệu chân cụ thể sẵn có cho PI7C9X760CZDE.

Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.

Ứng dụng tiêu biểu

PI7C9X760CZDE phù hợp cho 6 Áp dụngs: Handheld Serial Instruments, Industrial Serial Adapters, Sensor Control Systems, Embedded Data Acquisition, Battery-Powered Field Equipment, Portable Communications Modules.

📱

Handheld Serial Instruments

The PI7C9X760CZDE fits handheld instruments in which a low-power host processor uses I2C-bus or SPI while an internal module communicates through UART. Its maximum 33 Mbps data rate supports high-throughput serial transfers, while the 64-byte transmit and receive FIFOs help buffer traffic between differently timed bus transactions and the continuous UART stream. The 4 x 4 mm VQFN-24 package preserves board area in compact products, and the manufacturer's identification of low operating and sleeping current supports battery-conscious designs. Firmware should define transaction boundaries, UART baud rate, and error recovery before production testing.

🏭

Industrial Serial Adapters

The PI7C9X760CZDE can serve as the protocol-conversion element in a compact industrial serial adapter. A supervisory processor may manage configuration through I2C-bus or SPI while the bridge handles a UART connection to a downstream instrument or controller. The single-channel UART architecture avoids unnecessary parallel channels, and the 33 Mbps maximum rate accommodates high-speed data transfer. Eight programmable GPIO pins can support auxiliary status, control, or interrupt signaling. A production design must separately verify industrial temperature requirements, grounding, isolation, surge protection, and electromagnetic compatibility.

🧩

Sensor Control Systems

The PI7C9X760CZDE is suitable for sensor-control assemblies where a controller gathers data through I2C-bus or SPI but must forward commands or results to a UART-connected sensor head. The 64-byte transmit and receive FIFOs provide buffering between short host-side transactions and the serialized UART data path, while the eight GPIO pins can support sensor-enable, fault, or interrupt functions. Its small 4 x 4 mm VQFN-24 footprint limits board-space impact in distributed sensing equipment. Designers should validate timing margins, interrupt latency, and bus isolation for the deployed cable length.

🔧

Embedded Data Acquisition

The PI7C9X760CZDE can be used in embedded data-acquisition systems that standardize configuration traffic over I2C-bus or SPI while transferring measurement data through UART. The controller supports rates up to 33 Mbps, allowing the UART link to carry high-volume samples when the host-side interface remains organized in discrete transactions. Separate 64-byte transmit and receive FIFOs help absorb scheduling differences between the processor and peripheral. The eight programmable GPIO pins can indicate acquisition state or trigger downstream equipment. Firmware must define framing, checksums, overrun handling, and recovery behavior for uninterrupted laboratory or field operation.

⚡

Battery-Powered Field Equipment

The PI7C9X760CZDE is appropriate for battery-powered field equipment that needs a UART peripheral while conserving host-controller resources. The manufacturer PI7C9X760 datasheet identifies low operating and sleeping current, and the device provides up to eight programmable GPIO pins for compact auxiliary control functions. Its 33 Mbps maximum data rate permits short, high-speed exchanges, while the 64-byte FIFOs can reduce host-side servicing overhead. To calculate system-level battery impact, engineers should combine the device's operating and sleeping current with supply voltage, wake interval, UART activity, and the power characteristics of the attached peripherals.

🌐

Portable Communications Modules

The PI7C9X760CZDE fits portable communications modules that expose an I2C-bus or SPI configuration interface to a host processor and use UART for an internal or external link. Its small 24-pin VQFN package measures 4 mm on each side, making it useful in space-constrained radio, accessory, and wearable-adjacent products. The maximum 33 Mbps rate and bidirectional FIFOs support rapid command and data transfer, while the GPIO pins can carry module-state signals. The final design should budget connector space, UART grounding, signal integrity, and low-power behavior rather than treating the bridge as a substitute for RF front-end functions.

What is the PI7C9X760CZDE?
The PI7C9X760CZDE is a Diodes Incorporated single-channel I2C-bus/SPI to UART bridge controller in a 24-pin 4 x 4 mm VQFN package. According to the manufacturer PI7C9X760 datasheet, it supports data rates up to 33 Mbps, includes 64-byte transmit and receive FIFOs, and provides up to eight additional programmable GPIO pins. It is intended for embedded systems that need protocol conversion between an I2C-bus or SPI controller and a UART endpoint.
What are the key specifications of PI7C9X760CZDE that engineers should know?
The PI7C9X760CZDE combines a maximum data rate of 33 Mbps, one UART channel, 64-byte transmit and receive FIFOs, and up to eight programmable GPIO pins in a 24-pin VQFN package measuring 4 mm by 4 mm. The manufacturer PI7C9X760 datasheet also identifies low operating and sleeping current as key characteristics. These parameters make the controller suitable for compact embedded, portable, and industrial serial-bridge designs.
Where can I download the PI7C9X760CZDE datasheet PDF?
The official PI7C9X760CZDE datasheet PDF is available from Diodes Incorporated at https://www.diodes.com/datasheet/download/PI7C9X760.pdf. The document describes the I2C-bus/SPI-to-UART bridge function, 33 Mbps maximum data rate, FIFO resources, GPIO capability, electrical characteristics, pin configuration, and operating guidance. Use the document-number-free manufacturer PDF to verify all pin assignments and design limits.
Where can I find the PI7C9X760CZDE pinout?
The PI7C9X760CZDE pinout is documented in the pin-configuration section of the official PI7C9X760 datasheet at https://www.diodes.com/datasheet/download/PI7C9X760.pdf. The device uses a 24-pin 4 x 4 mm VQFN package. Assign signals only after checking the exposed-pad connection, supply pins, ground pins, serial interfaces, reset, clock, and GPIO multiplexing shown in the manufacturer diagram.
Is the PI7C9X760CZDE suitable for battery-operated devices?
Yes, the PI7C9X760CZDE is suitable for battery-operated and handheld equipment because the manufacturer PI7C9X760 datasheet identifies low operating and sleeping current as core features. Its I2C-bus/SPI-to-UART conversion also lets a compact host processor communicate with a UART peripheral without implementing that protocol directly. Actual battery-life calculations still require the application supply voltage, active-mode duration, and sleep-mode duration.
Can PI7C9X760CZDE bridge I2C and SPI to a UART peripheral?
Yes, the PI7C9X760CZDE can operate as an I2C-bus or SPI controller on the host side and present a UART interface on the peripheral side. According to the manufacturer PI7C9X760 datasheet, this single-channel bridge reaches data rates up to 33 Mbps and includes separate 64-byte transmit and receive FIFOs. Protocol selection, baud-rate configuration, addressing, and GPIO functions must be programmed through the device registers.
What is the difference between PI7C9X760CZDE and PI7C9X760CZDEX?
The PI7C9X760CZDE and PI7C9X760CZDEX identify the same PI7C9X760 interface-controller family, but their documented shipment formats differ. The CZDE listing identifies a tray, while the CZDEX distributor listing describes the extended packing designation. Both use the 24-pin VQFN (4 x 4 mm) package. Confirm the manufacturer ordering information before substituting one shipping suffix for another.
When should I choose PI7C9X760CZDE instead of implementing the protocol conversion in firmware?
Choose PI7C9X760CZDE when a system must handle a UART stream while its main controller communicates through I2C-bus or SPI and firmware-based conversion would consume processing time or complicate timing. The dedicated controller provides a maximum data rate of 33 Mbps and 64-byte transmit and receive FIFOs. It is less suitable when the host processor already has ample spare capacity, the required UART traffic is very low, or a simpler direct serial connection meets the design requirements.
Is PI7C9X760CZDE suitable for industrial serial adapters?
The PI7C9X760CZDE is suitable for compact industrial serial adapters that need a standard bus-to-UART conversion stage. Its single UART channel, maximum 33 Mbps data rate, programmable GPIO resources, and FIFO buffers support protocol bridging, while the 4 x 4 mm VQFN-24 package saves board area. Industrial qualification, operating-temperature limits, isolation, surge protection, and EMC requirements must be confirmed separately for the finished product.
What is the best drop-in replacement for PI7C9X760CZDE?
No independently verified drop-in replacement for the PI7C9X760CZDE has been established. A valid replacement must preserve the 24-pin VQFN footprint, pin assignments, I2C-bus/SPI-to-UART function, electrical limits, register behavior, and clocking requirements. PI7C9X760CZDEX is a different packing designation of the PI7C9X760 family, but it should not be selected merely because the suffix differs. Request a manufacturer-supported substitution for production use.
What can replace PI7C9X760CZDE on an existing PCB?
A component can replace the PI7C9X760CZDE only after its pinout and register behavior are verified against the original board. The replacement must use the same 24-pin VQFN footprint and preserve the I2C-bus/SPI, UART, FIFO, GPIO, supply, reset, and clock behavior. No cross-manufacturer equivalent with verified pin compatibility has been identified. Use the Request a Quote form on this page to discuss an exact, approved replacement request.
Is there a Diodes Incorporated equivalent with the same package and pinout?
No separately identified Diodes Incorporated equivalent has been confirmed as a pin-compatible replacement for the PI7C9X760CZDE. The official PI7C9X760CZDEX listing represents another ordering suffix within the same family, but the manufacturer ordering table must determine whether it is mechanically and electrically interchangeable with the CZDE tray version. Cross-reference search results alone do not establish register-level, pin-level, and timing compatibility.
How do I check the PI7C9X760CZDE supply and clock requirements?
Check the PI7C9X760CZDE supply and clock requirements in the electrical-characteristics and application sections of the official manufacturer PI7C9X760 datasheet. The verified product description confirms a 33 Mbps maximum data rate but does not state the numeric supply range or clock frequency, so those values must not be inferred. Final component selection also depends on the host logic levels, UART baud rate, SPI or I2C timing, and external clock arrangement.
Where can I buy PI7C9X760CZDE and request a quote?
Use the Request a Quote form on this page to request PI7C9X760CZDE pricing, stock, lead time, and order processing. The verified product listing identifies the exact CZDE part in a 490-piece tray format. Availability and lead time can change, so the quote form is the appropriate channel for current commercial terms rather than a static price claim. Include the required quantity, target date, and shipment destination in the request.
What is the lead time for PI7C9X760CZDE?
The current PI7C9X760CZDE lead time must be confirmed through the Request a Quote form on this page. The verified product record identifies a 490-piece tray format, but it does not establish a fixed factory lead time or current inventory position. Submit the required quantity, target receiving date, and shipment destination so the commercial team can provide a current schedule rather than an outdated estimate.
Is PI7C9X760CZDE currently in stock?
The current PI7C9X760CZDE inventory position must be confirmed through the Request a Quote form on this page. The product is identified in a 490-piece tray format, but that packaging description does not by itself establish present stock. Submit the required quantity and destination for a current availability response. For production planning, also request the manufacturer-approved lifecycle status and lead time.

Dữ liệu tham khảo kỹ thuật cho PI7C9X760CZDE — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.

Hướng dẫn chọn lựa

Choose the PI7C9X760CZDE when an embedded system must translate between an I2C-bus or SPI host interface and a UART peripheral and the link can operate as high as 33 Mbps. Its 64-byte transmit and receive FIFOs and eight programmable GPIO pins make it especially useful in compact handheld, industrial-adapter, sensor, and data-acquisition products. Choose a firmware conversion approach instead when traffic is infrequent, the host processor has ample spare capacity, and a simpler bill of materials outweighs the benefit of a dedicated bridge. A hardware UART already present in the host controller may also eliminate the need for this device. No verified drop-in substitute has been established, so an existing PI7C9X760 board should not be changed to another MPN until package, pins, registers, timing, and electrical limits have all been checked against the manufacturer documentation.

So sánh với các sản phẩm thay thế

Tham số Sản phẩm này
Manufacturer Diodes Incorporated
Package 24-pin VQFN, 4 mm x 4 mm
Product Type I2C-bus/SPI to single-channel UART bridge controller
Maximum Data Rate 33 Mbps
UART Channels 1 channel
Transmit FIFO 64 bytes
Receive FIFO 64 bytes
Programmable GPIO Up to 8 pins
Shipping Format Tray, 490 pieces

Bảo phân biệt quan trọng

  • High-speed protocol conversion in a compact package (vsFirmware-based I2C/SPI-to-UART conversion)
  • Bidirectional buffering for host-to-UART traffic (vsDirectly connected UART peripheral without a bridge)
  • Auxiliary digital control without expanding the package (vsA bridge using separate GPIO devices)

Ghi chú thiết kế

Treat the 24-pin VQFN as a high-speed mixed-signal layout problem. Place all required bypass capacitors immediately beside their associated supply and ground pins, connect the exposed pad to the appropriate ground plane with minimal via impedance, and provide uninterrupted return paths beneath serial traces. Keep I2C, SPI, and UART routes away from noisy power-conversion nodes and verify edge-rate-dependent crosstalk during prototype testing.

Configure signal levels, termination, and trace geometry from the actual clock, baud rate, and topology rather than from the 33 Mbps headline rate alone. Use continuous reference planes, avoid unnecessary stubs, and control impedance on long interconnects. For I2C-bus lines, verify pull-up voltage, capacitance, rise time, and the complete bus network; for SPI, check source-synchronous timing and return-path continuity across both chip-select and clock signals.

Do not assume that a similar PI7C9X760 packaging suffix is electrically and logistically interchangeable without checking the manufacturer ordering table. In particular, confirm that the CZDE tray version matches the required pinout, grade, quantity, and assembly process. During bring-up, test reset, clock startup, busy conditions, FIFO overflow, malformed frames, and recovery from an interrupted UART transaction so host firmware does not leave the bridge in an indeterminate state.

The 4 x 4 mm VQFN-24 package requires an exposed-pad-aware PCB footprint and adequate copper for heat spreading. Follow the manufacturer land pattern and solder-mask and paste recommendations rather than substituting a generic 24-pin footprint. Use the package thermal information and actual switching activity in the final thermal assessment, and inspect exposed-pad solder fill after assembly because an inadequate void pattern can materially increase junction temperature.

Thông tin tuân thủ

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Không chì
Unknown
Không halogen
Unknown
Khoáng vật xung đột
Unknown

No explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals statement was identified for this exact ordering code. AEC-Q100 qualification does not apply because this is an interface bridge controller rather than an automotive-qualified device.

Dữ liệu được xác minh vào: 2026-11-11 — dữ liệu được xác minh và quản lý bởi đội ngũ kỹ thuật phần cứng của XAIPART

Tìm kiếm liên quan

PI7C9X760CZDE datasheet PI7C9X760CZDE pinout PI7C9X760CZDE datasheet pdf PI7C9X760CZDE equivalent PI7C9X760CZDE replacement PI7C9X760CZDE cross reference PI7C9X760CZDE VQFN-24 PI7C9X760CZDE 33Mbps PI7C9X760CZDE UART bridge PI7C9X760CZDE vs PI7C9X760CZDEX PI7C9X760CZDE price PI7C9X760CZDE stock Diodes Incorporated PI7C9X760CZDE

Các bộ phận và thuật ngữ liên quan

Diodes Incorporated PI7C9X760CZDE PI7C9X760CZDEX PI7C9X760 I2C-bus SPI UART bridge controller interface IC serial interface semiconductor 33 Mbps 64-byte transmit FIFO 64-byte receive FIFO programmable GPIO VQFN-24 4 x 4 mm VQFN surface-mount package handheld electronics industrial serial adapter sensor control embedded data acquisition battery-operated equipment
Báo giá nhanh RFQ
Hãy điền đầy đủ thông tin — đội ngũ bán hàng của chúng tôi sẽ phản hồi trong vòng 24 giờ
Mã sản phẩm Nhà sản xuất Kiểu đóng gói QTY Giá mục tiêu Phụ
✓
Báo giá đã gửi!

Chúng tôi sẽ trả lời email của bạn trong vòng 24 giờ

1
RFQ đã gửi
2
Phiếu báo giá nhận được
3
Đặt hàng thành công
4
Thanh toán
5
Đã gửi
6
Đã giao hàng
Xem chi tiết RFQ