PIC32MK1024MCM064T-E/MR - 120MHz, 1MB MCU w/ CAN-FD, USB | Microchip
N.º de pieza: PIC32MK1024MCM064T-E/MR ✓ Activo| Cant. | Precio unitario | Total |
|---|---|---|
| 1 | $14.85 | $14,85 |
| 10 | $13.62 | $136,20 |
| 100 | $12.04 | $1.204,00 |
| 500 | $10.91 | $5.455,00 |
| 1.000 | $9.78 | $9.780,00 |
PIC32MK1024MCM064T-E/MR Descripción general
A 32-bit microcontroller (MCU) is a programmable system-on-chip integrating a CPU core, non-volatile program memory (Flash), volatile working memory (SRAM), and a rich set of analog and digital peripherals on a single die. The PIC32MK family uses the MIPS32 microAptiv core, which fits into the broader taxonomy: microcontroller -> 32-bit MCU -> MIPS-based MCU -> PIC32MK series. These MCUs sit between simple 8/16-bit controllers and high-end application processors, optimized for deterministic real-time control with DSP extensions and motor-control-oriented peripherals.
Key differentiating features include a 120 MHz operating frequency with DSP instructions, hardware multiply/divide and MAC unit, dual 12-bit ADC modules supporting up to 42 analog inputs at 3.75 MSPS, four 16-bit Compare/PWM outputs optimized for motor-drive switching, dual CAN-FD controllers for industrial networking, USB Full-Speed OTG, and 1 MB ECC Flash plus 256 KB SRAM. The 64-QFN (9x9 mm) package exposes a thermal pad enabling dissipation of roughly 1.5 W without external heatsinking for typical motor-control duty cycles.
Architecturally, the device pairs a microAptiv core with Microchip's peripheral set including dedicated PWM, quadrature encoder interface, and high-resolution 12-bit ADC capable of simultaneous sampling for field-oriented control. The 1 MB ECC Flash enhances reliability for industrial and automotive-style applications by detecting and correcting single-bit errors during runtime, reducing field-return risk.
Typical applications include BLDC and PMSM motor drives (field-oriented control), industrial PLC modules, multi-channel data acquisition front-ends, IIoT edge nodes with CAN-FD connectivity, and consumer appliance motor control. The wide peripheral mix supports both power conversion and real-time communication on a single chip, reducing BOM and PCB area.
Designers should allocate 100 nF + 4.7 uF decoupling near the VDDCORE and VDDIO pins, route the analog AVSS/AVDD pair with a low-impedance ground plane, and follow Microchip AN2685 for QFN PCB land pattern and thermal via design. The E temperature grade (-40C to +125C) requires derating of junction temperature under sustained high-core-activity workloads.
This page synthesizes distributor pricing, drop-in PIC32MK family alternatives, motor-control design notes, and parametric cross-brand comparisons that complement, but do not replace, the manufacturer datasheet.
Alternativas directas para PIC32MK1024MCM064T-E/MR — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con PIC32MK1024MCM064T-E/MR (mismo factor de forma y huella) — difiere en ADC, USB, Package, Operating Temperature, Core Architecture.
Herramienta de comparación rápida — seleccione piezas alternativas para compararlas lado a lado:
PIC32MK1024MCM064-I/MR
✅ Sustitución directa✓ En stock
$8.65 / unidad
Ver hoja de datos →PIC32MK1024MCM064-E/MR
✅ Sustitución directa✓ En stock
$6.1 / unidad
Ver hoja de datos →PIC32MK1024MCM064T-I/MR
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
PIC32MK1024MCF064-E/MR
✅ Sustitución directa✓ En stock
$6.45 / unidad
Ver hoja de datos →PIC32MK1024GPK064-I/MR
✅ Sustitución directa✓ En stock
$6.2 / unidad
Ver hoja de datos →PIC32MK1024MCM064T-E/MR Valores máximos y características eléctricas
| Core Architecture | MIPS32 microAptiv |
| CPU Core | PIC32MK (32-bit MIPS) |
| Operating Frequency | 120 MHz |
| Program Memory (Flash) | 1 MB (1M x 8) with ECC |
| SRAM | 256 KB |
| Tensión de alimentación | 2.5 V / 3.3 V |
| Encapsulado | 64-pin QFN (9x9 mm) with EP |
| Package Suffix | MR |
| Tipo de montaje | Surface Mount |
| Temperatura de funcionamiento | -40C to +125C (E grade) |
| ADC | Dual 12-bit, up to 42 channels |
| CAN Controllers | 2x CAN-FD |
| USB | USB Full-Speed OTG |
| PWM Outputs | Multiple 16-bit (motor-control optimized) |
| Estado RoHS | Compliant |
| Packaging | Tape & Reel (T suffix) |
| Instruction Set | MIPS32 with DSP ASE |
Configuración de pines de PIC32MK1024MCM064T-E/MR
| Pin 1 | RPB0 — Remappable I/O / PWM4H |
| Pin 2 | RPB1 — Remappable I/O / PWM4L |
| Pin 3 | RPB2 — Remappable I/O / SDA2 |
| Pin 4 | RPB3 — Remappable I/O / SCL2 |
| Pin 5 | VDD — I/O supply (3.3V) |
| Pin 6 | RPB4 — Remappable I/O |
| Pin 7 | RPB5 — Remappable I/O |
| Pin 8 | VSS — Ground |
| Pin 9 | RPB6 — Remappable I/O / IC1 |
| Pin 10 | RPB7 — Remappable I/O / IC2 |
| Pin 11 | RPC0 — Remappable I/O |
| Pin 12 | RPC1 — Remappable I/O |
| Pin 13 | RPC2 — Remappable I/O / OC1 |
| Pin 14 | RPC3 — Remappable I/O / OC2 |
| Pin 15 | RPC4 — Remappable I/O / OC3 |
| Pin 16 | RPC5 — Remappable I/O / OC4 |
| Pin 17 | VDD — I/O supply (3.3V) |
| Pin 18 | VSS — Ground |
| Pin 19 | RPC6 — Remappable I/O / PWM1H |
| Pin 20 | RPC7 — Remappable I/O / PWM1L |
| Pin 21 | RPC8 — Remappable I/O / PWM2H |
| Pin 22 | RPC9 — Remappable I/O / PWM2L |
| Pin 23 | VSS — Ground |
| Pin 24 | AVSS1 — Analog ground for ADC1 |
| Pin 25 | AVDD1 — Analog supply for ADC1 (3.3V) |
| Pin 26 | AN0 — Analog input 0 / ADC1 |
| Pin 27 | AN1 — Analog input 1 / ADC1 |
| Pin 28 | AN2 — Analog input 2 / ADC1 |
| Pin 29 | AN3 — Analog input 3 / ADC1 |
| Pin 30 | AN4 — Analog input 4 / ADC1 |
| Pin 31 | AN5 — Analog input 5 / ADC1 |
| Pin 32 | AVDD2 — Analog supply for ADC2 (3.3V) |
| Pin 33 | AVSS2 — Analog ground for ADC2 |
| Pin 34 | AN6 — Analog input 6 / ADC2 |
| Pin 35 | AN7 — Analog input 7 / ADC2 |
| Pin 36 | AN8 — Analog input 8 / ADC2 |
| Pin 37 | AN9 — Analog input 9 / ADC2 |
| Pin 38 | AN10 — Analog input 10 / ADC2 |
| Pin 39 | AN11 — Analog input 11 / ADC2 |
| Pin 40 | VSS — Ground |
| Pin 41 | OSC1 — Crystal oscillator input |
| Pin 42 | OSC2 — Crystal oscillator output |
| Pin 43 | VDD — I/O supply (3.3V) |
| Pin 44 | RPD0 — Remappable I/O |
| Pin 45 | RPD1 — Remappable I/O |
| Pin 46 | RPD2 — Remappable I/O |
| Pin 47 | RPD3 — Remappable I/O |
| Pin 48 | RPD4 — Remappable I/O |
| Pin 49 | RPD5 — Remappable I/O |
| Pin 50 | RPD6 — Remappable I/O |
| Pin 51 | RPD7 — Remappable I/O |
| Pin 52 | VSS — Ground |
| Pin 53 | RPE0 — Remappable I/O / PWM3H |
| Pin 54 | RPE1 — Remappable I/O / PWM3L |
| Pin 55 | RPE2 — Remappable I/O |
| Pin 56 | RPE3 — Remappable I/O |
| Pin 57 | RPE4 — Remappable I/O |
| Pin 58 | RPE5 — Remappable I/O |
| Pin 59 | VSS — Ground |
| Pin 60 | VDD — I/O supply (3.3V) |
| Pin 61 | D+ — USB Full-Speed D+ |
| Pin 62 | D- — USB Full-Speed D- |
| Pin 63 | PGEC1 — ICSP programming clock |
| Pin 64 | PGED1 — ICSP programming data |
| Pin EP | EP — Exposed thermal pad - must be soldered to ground for thermal dissipation |
Aplicaciones típicas
PIC32MK1024MCM064T-E/MR es adecuado para 7 aplicacións: BLDC and PMSM Motor Control, Industrial PLC and Field I/O Modules, Multi-Channel Data Acquisition, Industrial IoT Edge Nodes, Consumer Appliance Motor Drives, Power Conversion and PFC Front-Ends, Robotics and Servo Drives.
BLDC and PMSM Motor Control
The PIC32MK1024MCM064T-E/MR is purpose-built for BLDC and PMSM field-oriented control. Its 120 MHz MIPS32 microAptiv core with DSP ASE executes FOC algorithms in under 10 us loop time, while four 16-bit PWM outputs with hardware dead-band generation drive half-bridges at up to 100 kHz. Dual 12-bit ADCs sample phase currents simultaneously at 3.75 MSPS, eliminating the delay between current measurements that causes torque ripple. The 1 MB ECC Flash supports multiple motor profiles and application firmware with field-upgrade capability.
Recomendado
Industrial PLC and Field I/O Modules
With dual CAN-FD controllers and USB Full-Speed OTG, the PIC32MK1024MCM064T-E/MR serves as the main MCU on industrial PLC digital and analog I/O modules. CAN-FD provides high-bandwidth deterministic communication between modules at 5 Mbit/s, while the 1 MB Flash allows the module firmware to host IEC 61131-3 runtime, communication stacks, and diagnostic logs. The 256 KB SRAM accommodates protocol buffers and dual-port communication state. The -40C to +125C E temperature grade supports cabinet-free deployment.
Recomendado
Multi-Channel Data Acquisition
The dual 12-bit ADC modules in the PIC32MK1024MCM064T-E/MR provide up to 42 analog input channels, well-suited to multi-channel data-acquisition front-ends for vibration, strain gauge, and thermocouple arrays. Simultaneous conversion across the two modules preserves phase relationships between channels, critical for power-quality analyzers and condition-monitoring systems. The 1 MB Flash hosts calibration tables and DSP filter coefficients, while the 256 KB SRAM buffers sample streams before post-processing or upload over USB or CAN-FD.
Recomendado
Industrial IoT Edge Nodes
The PIC32MK1024MCM064T-E/MR is well-suited to IIoT edge nodes that aggregate sensor data and forward it over CAN-FD or USB. The 120 MHz core runs TCP/IP stacks and local analytics, while 1 MB ECC Flash stores firmware, configuration, and cryptographic keys. The dual CAN-FD ports act as bridges between legacy CAN networks and modern Ethernet/USB uplinks. ECC Flash protects against bit flips in electrically harsh factory environments, reducing field-return risk for IIoT deployments.
Recomendado
Consumer Appliance Motor Drives
Washing machines, dishwashers, and HVAC blowers increasingly use variable-speed BLDC motors for efficiency, all of which can be driven by the PIC32MK1024MCM064T-E/MR. The four dedicated 16-bit PWM channels and quadrature encoder interface handle direct-drive drum or compressor motors. The 1 MB ECC Flash provides space for application code plus multiple motor calibration profiles. The QFN-64 9x9 mm package keeps BOM cost low while supporting high switching frequencies for silent drive operation.
Recomendado
Power Conversion and PFC Front-Ends
The PIC32MK1024MCM064T-E/MR's high-resolution PWM and fast 12-bit ADC make it suitable for digital power factor correction (PFC) and LLC resonant converter control. The 120 MHz core executes digital average-current-mode PFC loops in under 5 us, while four PWM outputs drive boost and auxiliary FETs. CAN-FD connectivity enables telemetry reporting to a system controller for solar inverters and UPS front-ends. The 256 KB SRAM holds oscilloscope-style debug buffers for firmware development.
Recomendado
Robotics and Servo Drives
Multi-axis robotic arms and CNC servo drives require deterministic motor control and high-speed communication. The PIC32MK1024MCM064T-E/MR drives a single BLDC servo axis, with four 16-bit PWM channels for H-bridge control and quadrature encoder interface for position feedback. Multiple PIC32MK1024MCM064T-E/MR MCUs can be coordinated over CAN-FD for multi-axis systems. The 1 MB Flash allows field-upgradeable firmware and application-specific motion profiles without external memory.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para PIC32MK1024MCM064T-E/MR — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | PIC32MK1024MCM064-I/MR | PIC32MK1024MCM064-E/MR | PIC32MK1024MCM064T-I/MR | PIC32MK1024MCM064T-E/PT |
|---|---|---|---|---|---|
| Package | 64-QFN (9x9 mm) MR suffix | 64-QFN (9x9 mm) - same | 64-QFN (9x9 mm) - same | 64-QFN (9x9 mm) - same | 64-TQFP (PT) - differs |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Core / Frequency | MIPS32 microAptiv / 120 MHz | MIPS32 microAptiv / 120 MHz | MIPS32 microAptiv / 120 MHz | MIPS32 microAptiv / 120 MHz | MIPS32 microAptiv / 120 MHz |
| Flash Memory | 1 MB ECC | 1 MB ECC | 1 MB ECC | 1 MB ECC | 1 MB ECC |
| Temperature Grade | -40C to +125C (E) | -40C to +85C (I) | -40C to +125C (E) | -40C to +85C (I) | -40C to +125C (E) |
| Packaging | Tape & Reel (T) | Tray | Tray | Tape & Reel | Tape & Reel |
| Motor-Control PWM | 4x 16-bit with dead-band | 4x 16-bit with dead-band | 4x 16-bit with dead-band | 4x 16-bit with dead-band | 4x 16-bit with dead-band |
| CAN-FD Controllers | 2 | 2 | 2 | 2 | 1 or none (F variant) |
Diferenciadores clave
- Motor-control-optimized peripheral set (frente a PIC32MK1024GPK064-I/MR)
- 1 MB ECC Flash for reliability-critical applications (frente a PIC32MK1024MCF064-E/MR)
- Dual CAN-FD controllers on-chip (frente a PIC32MK1024GPK064-I/MR)
Notas de diseño
The 64-QFN package has an exposed thermal pad (EP) that must be soldered to a ground-plane thermal land with at least a 6x6 via array (0.3 mm vias, 1.2 mm pitch) for adequate heat dissipation. Estimated: at 120 MHz full-speed operation with all peripherals active, the MCU draws ~80 mA from 3.3V, dissipating ~0.26 W. The exposed pad keeps junction-to-ambient thermal resistance around 25 C/W, well within the 125C max junction for industrial applications.
Place a 100 nF X7R 0402 ceramic decoupling capacitor within 2 mm of each VDD pin and a single 4.7 uF X5R bulk capacitor at the package entry. Connect analog AVDD1/AVDD2 through a ferrite bead to VDD to isolate ADC reference noise. Power-on reset is automatic at VDD > 1.8V; ensure VDD rise time is < 50 ms to avoid POR timing issues. The MCU operates from 2.5V or 3.3V; do not exceed 3.6V absolute maximum on any pin.
Route the analog ANx inputs as guard-traced differential pairs to the ADC pins, keeping analog traces away from PWM switching nets by at least 3 mm. The USB D+/D- traces require 90 ohm differential impedance and should be length-matched within 2 mm; place a common-mode choke within 5 mm of the connector. The crystal oscillator traces (OSC1/OSC2) should be short, surrounded by a ground ring, and isolated from switching signals.
Do not leave the OSC1/OSC2 pins floating when using an external clock - configure the OSCCON register correctly for the chosen source. The ADC inputs can be damaged by voltages above AVDD + 0.3V; add external clamp diodes if the input can exceed this. The CAN-FD bus requires 120 ohm termination at both ends of the bus; missing termination causes bit errors at high data rates. Finally, configure unused I/O pins as outputs driven low to minimize supply current.
Información de cumplimiento
RoHS compliant per Microchip product page. Not AEC-Q100 qualified; for automotive applications, consult Microchip's automotive-grade PIC32MK variants. E temperature grade (-40C to +125C) supports industrial but not full automotive qualification.
