SI3226-E-GQ - Dual-Channel 3.3V ProSLIC | Skyworks Solutions
N.º de pieza: SI3226-E-GQ ✗ Fin de vidaSI3226-E-GQ Descripción general
A subscriber-line interface circuit, commonly called a SLIC, terminates an analog telephone line, applies the appropriate DC line voltage and current, and converts the analog voice signal into a digital PCM stream. The CODEC section performs the complementary digital-to-analog and analog-to-digital conversion. Integrating these functions into one device reduces the number of external line-interface components, simplifies board layout, and helps designers create compact, consistent two-channel voice-processing modules.
The SI3226-E-GQ provides two complete FXS telephony channels, 3.3 V operation, and interfaces identified as GCI, PCM, and SPI. Its dual DC-DC controllers support the power-conversion functions associated with two line channels. The 64-TQFP package provides the physical interface used by the Si3226x Single-Chip Dual ProSLIC family. The architecture is intended for low-voltage CMOS telephony equipment requiring consolidated SLIC and CODEC functionality.
The 3.3 V supply requirement suits equipment designed around modern low-voltage digital logic. Designers must follow the manufacturer's recommendations for bypass capacitors, clocking, line-interface components, PCB grounding, and exposed-pad or thermal management where applicable. Because the device integrates sensitive analog line functions with digital control logic, layout quality can affect signal integrity, return noise, and system compliance. Follow the reference schematic and component values in the manufacturer datasheet rather than deriving them solely from the catalog description.
Typical uses include Voice over IP endpoint hardware, digital telephone exchanges, voice gateways, customer-premises equipment, line-card modules, embedded telephony controllers, and dual-channel access equipment. In a Voice over IP terminal, the SI3226-E-GQ can handle the analog line termination and PCM voice conversion while the system processor manages packetization and call control. In access equipment, the same dual-channel organization supports two subscriber lines per device and can simplify channel-density planning.
The principal engineering trade-off is integration versus board flexibility. A combined SLIC, CODEC, and DC-DC controller reduces external circuitry and board area, but the design remains tightly dependent on correct external component selection and layout. Confirm loop current, line impedance, hook-state behavior, tone generation, clock requirements, and power sequencing against the exact datasheet revision before production release.
This page consolidates the key SI3226-E-GQ specifications, package information, drop-in replacement evidence, comparison criteria, and practical integration guidance. It also identifies which parameters must be checked against the manufacturer datasheet before layout or production decisions are finalized.
Alternativas directas para SI3226-E-GQ — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con SI3226-E-GQ (mismo factor de forma y huella) — difiere en Package, Product Type, Supply Voltage.
SI3226-E-FQ
✅ Sustitución directaConsulte el precio
Ver hoja de datos →SI3226-E-GQ Especificaciones
| Product Type | Dual-channel ProSLIC telecom interface IC |
| Number of Channels | 2 channels |
| Integrated Functions | SLIC, CODEC, and dual DC-DC controllers |
| Tensión de alimentación | 3.3 V |
| Process Technology | Low-voltage CMOS |
| Interfaz | GCI, PCM, and SPI |
| Telephony Interface | Dual foreign-exchange station (FXS) interface |
| Encapsulado | 64-pin TQFP, 10 x 10 mm |
| Tipo de montaje | Surface mount |
| Recuento de pines | 64 pins |
| Lead Status | Lead-free |
| Automotive Qualification | Not applicable |
Guía de configuración de pines de SI3226-E-GQ 64-pin tqfp, 10 x 10 mm
Configuración de pines para SI3226-E-GQ (encapsulado 64-pin tqfp, 10 x 10 mm). La numeración de pines, las funciones y los diagramas de conexión se definen en la hoja de datos del fabricante. Consúltela para conocer el footprint exacto y las directrices de soldadura.
No hay datos detallados de patillaje disponibles para SI3226-E-GQ.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
SI3226-E-GQ es adecuado para 6 aplicacións: Voice over IP Endpoint, Digital Telephone Exchange, Voice Gateway, Customer Premises Equipment, Line-Card Module, Embedded Telephony Controller.
Voice over IP Endpoint
The SI3226-E-GQ fits a Voice over IP endpoint that must terminate two analog telephone lines while connecting voice traffic to a digital processor. Its two integrated FXS channels, CODEC function, 3.3 V supply, and PCM interface support the analog-to-digital and digital-to-analog conversion path without requiring a separate CODEC device for each line. The dual-channel organization can reduce board area and simplify shared clock, control, and power distribution. The principal design consideration is preserving clean separation between the sensitive analog line paths and the digital PCM, SPI, and GCI routing. Use the manufacturer's reference circuit for transformer or external line-interface components, bypass capacitors, and grounding. Verify regional line-voltage, loop-current, ringing, and codec timing requirements before production release.
Recomendado
Digital Telephone Exchange
The SI3226-E-GQ is suitable for channel-dense digital exchange equipment requiring two subscriber-line interfaces per IC. Integrating SLIC, CODEC, and dual DC-DC controller functions in a 64-pin TQFP allows a line card to place two FXS channels in a controlled, repeatable footprint. The 3.3 V operation fits modern low-voltage digital logic, while PCM provides a conventional voice-data path to the exchange backplane. Because line-interface designs are sensitive to grounding and return noise, the board should follow the manufacturer layout guidance and maintain controlled return-current paths. Pay particular attention to thermal margin, isolated-network requirements, component tolerances, and channel-to-channel crosstalk during qualification. Confirm exact ordering attributes and production availability with the manufacturer or an authorized sourcing channel.
Recomendado
Voice Gateway
The SI3226-E-GQ can provide the analog line side of a voice gateway with two FXS channels per device. The integrated CODEC supports conversion between analog voice and digital PCM samples, while the 3.3 V operating supply simplifies power coordination with gateway logic operating at similar voltage levels. Designers can use the two-channel arrangement to improve line density while retaining a single package and shared control structure. A gateway design must still provide the correct external line network, overvoltage protection, and isolation or non-isolation approach required by its target market. Validate acoustic performance, tone generation, caller-ID signaling, hook-state behavior, and loop-current limits against the applicable product requirements. Use the exact datasheet revision as the controlling document for component values and timing.
Recomendado
Customer Premises Equipment
The SI3226-E-GQ is appropriate for CPE that bridges legacy analog telephone equipment to digital packet networks. Two integrated FXS channels can support two analog ports, and the combination of SLIC, CODEC, and DC-DC control functions helps reduce the external component count compared with separate implementations. The 64-pin TQFP package also supports compact, automated PCB assembly when the land pattern and pin assignments follow the manufacturer drawings. The design should include appropriate surge protection and isolation components because the device connects directly to external telephone lines. Review thermal performance at the highest expected line activity and verify boot behavior when the 3.3 V rail changes. Regulatory and network-interface certification should be completed on the finished CPE rather than inferred from the integrated IC alone.
Recomendado
Line-Card Module
The SI3226-E-GQ can be used in modular subscriber line cards where channel density and predictable routing are priorities. Each 64-pin device provides two FXS interfaces, CODEC functionality, and dual DC-DC controller resources from a 3.3 V supply. That integration can simplify backplane connections by keeping both line channels on one controlled device. Layout should separate line-side energy from sensitive codec and digital-control sections, with careful treatment of power and ground returns under worst-case line loading. The module designer should also plan clock distribution, reset behavior, test access, and per-channel line-network components into the initial PCB rather than adding them later. Confirm thermal performance, channel count, and exact supported temperature grade using the manufacturer ordering guide before deployment.
Recomendado
Embedded Telephony Controller
The SI3226-E-GQ is suitable for embedded telephony controllers that must expose analog telephone functionality to a host processor. The GCI, PCM, and SPI interfaces support digital voice and control connectivity, while the two FXS channels provide line termination and codec functions in one package. The 3.3 V supply operation allows careful co-design with modern embedded processors and low-voltage logic. Firmware and hardware teams should define clocking, reset, interrupt, and signaling behavior together so digital timing remains consistent with the analog line interface. External protection, isolation, and network components must be selected for the target deployment environment. Validate system-level calls, hook transitions, tone generation, and line loading in production-like hardware to ensure that the integrated implementation meets both functional and regulatory expectations.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para SI3226-E-GQ — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | SI3226-E-FQ |
|---|---|---|
| Brand | Skyworks Solutions | Skyworks Solutions |
| Package | 64-pin TQFP (10 x 10 mm) | 64-pin TQFP (10 x 10 mm) |
| Device Type | Dual-channel ProSLIC | Dual-channel SLIC/CODEC |
| Number of Channels | 2 channels | 2 channels |
| Supply Voltage | 3.3 V | 3.3 V |
| Integrated Functions | SLIC, CODEC, and dual DC-DC controllers | SLIC/CODEC with dual DC-DC controllers |
| Telephony Configuration | Two complete FXS interfaces | Two-channel subscriber-line interface |
Diferenciadores clave
- Consolidates two complete FXS channels with CODEC and dual DC-DC controller functions (frente a SI3226-E-FQ)
- Supports a clearly documented digital control interface set (frente a SI3226-E-FQ)
- Operates from a modern 3.3 V supply (frente a SI3226-E-FQ)
Notas de diseño
Separate the analog line-side paths from PCM, SPI, and GCI digital routing, and provide a continuous ground reference beneath the device. Keep the external line-network components and their high-energy return currents away from codec and clock inputs. Use the manufacturer reference layout to establish component placement, copper geometry, and via placement rather than relying only on the 10 x 10 mm package outline.
Design the 3.3 V rail around transient and thermal requirements rather than steady-state current alone. Place required bypass capacitors adjacent to the relevant supply pins with very short ground returns, and account for the load presented by two active line channels and their DC-DC controllers. Validate startup, shutdown, line seizure, and ringing conditions on hardware because activity patterns can change rail demand beyond nominal operating load.
Do not treat the GQ and FQ ordering codes as interchangeable without checking the manufacturer's ordering guide. Confirm the exact temperature grade, lead finish, packing form, and lifecycle designation, then perform a pin-by-pin and function-by-function comparison against the current datasheet. A shared package outline alone does not establish regulatory, temperature, or production suitability.
Evaluate junction temperature with both line channels active, ringing present, and the highest supported ambient condition. The 64-pin TQFP requires adequate copper around its thermal lands and a PCB stackup that supports the manufacturer's thermal assumptions. Use the datasheet thermal model for final qualification; board-area and airflow choices materially affect the available temperature margin.
Información de cumplimiento
The available listing identifies the related GQR variant as lead-free. RoHS, REACH, halogen-free, and conflict-minerals status for the exact SI3226-E-GQ ordering code are not established by the available records.