Skyworks Solutions

SI3226-E-GQ - Dual-Channel 3.3V ProSLIC | Skyworks Solutions

MPN: SI3226-E-GQ ✗ پایان تولید
3.3 V Vdss 64-pin TQFP, 10 x 10 mm Package
حداقل سفارش: 1 |

SI3226-E-GQ نمای کلی

Skyworks Solutions SI3226-E-GQ is a dual-channel ProSLIC telecom interface IC that integrates two complete foreign-exchange station telephony interfaces into one 64-pin TQFP package. It operates from a 3.3 V supply and combines SLIC, CODEC, and dual DC-DC controller functionality for subscriber-line interface circuits. Each channel supports the signal conversion and line-driver functions required between a digital voice system and analog telephone lines.

A subscriber-line interface circuit, commonly called a SLIC, terminates an analog telephone line, applies the appropriate DC line voltage and current, and converts the analog voice signal into a digital PCM stream. The CODEC section performs the complementary digital-to-analog and analog-to-digital conversion. Integrating these functions into one device reduces the number of external line-interface components, simplifies board layout, and helps designers create compact, consistent two-channel voice-processing modules.

The SI3226-E-GQ provides two complete FXS telephony channels, 3.3 V operation, and interfaces identified as GCI, PCM, and SPI. Its dual DC-DC controllers support the power-conversion functions associated with two line channels. The 64-TQFP package provides the physical interface used by the Si3226x Single-Chip Dual ProSLIC family. The architecture is intended for low-voltage CMOS telephony equipment requiring consolidated SLIC and CODEC functionality.

The 3.3 V supply requirement suits equipment designed around modern low-voltage digital logic. Designers must follow the manufacturer's recommendations for bypass capacitors, clocking, line-interface components, PCB grounding, and exposed-pad or thermal management where applicable. Because the device integrates sensitive analog line functions with digital control logic, layout quality can affect signal integrity, return noise, and system compliance. Follow the reference schematic and component values in the manufacturer datasheet rather than deriving them solely from the catalog description.

Typical uses include Voice over IP endpoint hardware, digital telephone exchanges, voice gateways, customer-premises equipment, line-card modules, embedded telephony controllers, and dual-channel access equipment. In a Voice over IP terminal, the SI3226-E-GQ can handle the analog line termination and PCM voice conversion while the system processor manages packetization and call control. In access equipment, the same dual-channel organization supports two subscriber lines per device and can simplify channel-density planning.

The principal engineering trade-off is integration versus board flexibility. A combined SLIC, CODEC, and DC-DC controller reduces external circuitry and board area, but the design remains tightly dependent on correct external component selection and layout. Confirm loop current, line impedance, hook-state behavior, tone generation, clock requirements, and power sequencing against the exact datasheet revision before production release.

This page consolidates the key SI3226-E-GQ specifications, package information, drop-in replacement evidence, comparison criteria, and practical integration guidance. It also identifies which parameters must be checked against the manufacturer datasheet before layout or production decisions are finalized.

جایگزین‌های drop-in برای SI3226-E-GQ — همان پکیج، سازگار پین‌به‌پین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.

گونه‌ها در این سری

مدل‌های هم‌سری که جایگزین مستقیم هستند برای SI3226-E-GQ (همان فرم‌فاکتور و فوت‌پرینت) — متفاوت در Package, Product Type, Supply Voltage.

Skyworks Solutions
Package: 64-TQFP
Product Type: Subscriber Line Interface Concept (SLIC) and CODEC
Supply Voltage: 3.3 V single supply
مقایسه با SI3226-E-GQ →

SI3226-E-FQ

✅ جایگزین مستقیم
Skyworks Solutions
📦 64-pin TQFP (10 x 10 mm)
Subscriber Line Interface Concept (SLIC) and CODEC · 2 channels · 3.3 V single supply · PCM, SPI, or GCI · 64-TQFP · 10 mm x 10 mm · Surface mount · Two complete FXS telephony interfaces

برای قیمت تماس بگیرید

مشاهده دیتاشیت ←

SI3226-E-GQ مشخصات

Product Type Dual-channel ProSLIC telecom interface IC
Number of Channels 2 channels
Integrated Functions SLIC, CODEC, and dual DC-DC controllers
ولتاژ تغذیه 3.3 V
Process Technology Low-voltage CMOS
رابط GCI, PCM, and SPI
Telephony Interface Dual foreign-exchange station (FXS) interface
بسته‌بندی 64-pin TQFP, 10 x 10 mm
نوع نصب Surface mount
تعداد پایه 64 pins
Lead Status Lead-free
Automotive Qualification Not applicable

راهنمای پیکربندی پین SI3226-E-GQ 64-pin tqfp, 10 x 10 mm

پیکربندی پین برای SI3226-E-GQ (پکیج 64-pin tqfp, 10 x 10 mm). شماره‌گذاری پایه‌ها، عملکردها و نمودارهای اتصال در دیتاشیت سازنده تعریف شده است. برای footprint دقیق و دستورالعمل‌های لحیم‌کاری به آن مراجعه کنید.

نمودار پین‌آوت پکیج 64-pin tqfp, 10 x 10 mm برای SI3226-E-GQ

داده پین‌آوت تفصیلی موجود نیست برای SI3226-E-GQ.

به دیتاشیت برای پیکربندی کامل پین‌ها.

کاربردهای معمول

SI3226-E-GQ مناسب است برای 6 کاربردs: Voice over IP Endpoint, Digital Telephone Exchange, Voice Gateway, Customer Premises Equipment, Line-Card Module, Embedded Telephony Controller.

📱

Voice over IP Endpoint

The SI3226-E-GQ fits a Voice over IP endpoint that must terminate two analog telephone lines while connecting voice traffic to a digital processor. Its two integrated FXS channels, CODEC function, 3.3 V supply, and PCM interface support the analog-to-digital and digital-to-analog conversion path without requiring a separate CODEC device for each line. The dual-channel organization can reduce board area and simplify shared clock, control, and power distribution. The principal design consideration is preserving clean separation between the sensitive analog line paths and the digital PCM, SPI, and GCI routing. Use the manufacturer's reference circuit for transformer or external line-interface components, bypass capacitors, and grounding. Verify regional line-voltage, loop-current, ringing, and codec timing requirements before production release.

🌐

Digital Telephone Exchange

The SI3226-E-GQ is suitable for channel-dense digital exchange equipment requiring two subscriber-line interfaces per IC. Integrating SLIC, CODEC, and dual DC-DC controller functions in a 64-pin TQFP allows a line card to place two FXS channels in a controlled, repeatable footprint. The 3.3 V operation fits modern low-voltage digital logic, while PCM provides a conventional voice-data path to the exchange backplane. Because line-interface designs are sensitive to grounding and return noise, the board should follow the manufacturer layout guidance and maintain controlled return-current paths. Pay particular attention to thermal margin, isolated-network requirements, component tolerances, and channel-to-channel crosstalk during qualification. Confirm exact ordering attributes and production availability with the manufacturer or an authorized sourcing channel.

🏭

Voice Gateway

The SI3226-E-GQ can provide the analog line side of a voice gateway with two FXS channels per device. The integrated CODEC supports conversion between analog voice and digital PCM samples, while the 3.3 V operating supply simplifies power coordination with gateway logic operating at similar voltage levels. Designers can use the two-channel arrangement to improve line density while retaining a single package and shared control structure. A gateway design must still provide the correct external line network, overvoltage protection, and isolation or non-isolation approach required by its target market. Validate acoustic performance, tone generation, caller-ID signaling, hook-state behavior, and loop-current limits against the applicable product requirements. Use the exact datasheet revision as the controlling document for component values and timing.

🏠

Customer Premises Equipment

The SI3226-E-GQ is appropriate for CPE that bridges legacy analog telephone equipment to digital packet networks. Two integrated FXS channels can support two analog ports, and the combination of SLIC, CODEC, and DC-DC control functions helps reduce the external component count compared with separate implementations. The 64-pin TQFP package also supports compact, automated PCB assembly when the land pattern and pin assignments follow the manufacturer drawings. The design should include appropriate surge protection and isolation components because the device connects directly to external telephone lines. Review thermal performance at the highest expected line activity and verify boot behavior when the 3.3 V rail changes. Regulatory and network-interface certification should be completed on the finished CPE rather than inferred from the integrated IC alone.

🖥️

Line-Card Module

The SI3226-E-GQ can be used in modular subscriber line cards where channel density and predictable routing are priorities. Each 64-pin device provides two FXS interfaces, CODEC functionality, and dual DC-DC controller resources from a 3.3 V supply. That integration can simplify backplane connections by keeping both line channels on one controlled device. Layout should separate line-side energy from sensitive codec and digital-control sections, with careful treatment of power and ground returns under worst-case line loading. The module designer should also plan clock distribution, reset behavior, test access, and per-channel line-network components into the initial PCB rather than adding them later. Confirm thermal performance, channel count, and exact supported temperature grade using the manufacturer ordering guide before deployment.

🔧

Embedded Telephony Controller

The SI3226-E-GQ is suitable for embedded telephony controllers that must expose analog telephone functionality to a host processor. The GCI, PCM, and SPI interfaces support digital voice and control connectivity, while the two FXS channels provide line termination and codec functions in one package. The 3.3 V supply operation allows careful co-design with modern embedded processors and low-voltage logic. Firmware and hardware teams should define clocking, reset, interrupt, and signaling behavior together so digital timing remains consistent with the analog line interface. External protection, isolation, and network components must be selected for the target deployment environment. Validate system-level calls, hook transitions, tone generation, and line loading in production-like hardware to ensure that the integrated implementation meets both functional and regulatory expectations.

What is the SI3226-E-GQ?
The SI3226-E-GQ is a dual-channel ProSLIC telecom interface IC that combines two complete FXS telephony interfaces with CODEC and dual DC-DC controller functions. According to the Skyworks Si3226x product information, the device operates from a 3.3 V supply and integrates both subscriber-line and voice-codec functions in a single 64-pin TQFP package.
How many telephony channels does the SI3226-E-GQ support?
The SI3226-E-GQ supports two independent telephony channels. Skyworks describes the Si3226x family as implementing two complete foreign-exchange station interfaces in one package. This two-channel architecture lets one device serve two subscriber lines while sharing a common 3.3 V supply, digital interface, and physical package.
What is the operating voltage of the SI3226-E-GQ?
The SI3226-E-GQ operates from a 3.3 V supply. This figure is stated in the Skyworks Si3226x Single-Chip Dual ProSLIC product information. The complete supply limits, tolerances, sequencing conditions, and operating-temperature behavior should be confirmed in the manufacturer datasheet before power-supply design is released.
Which interfaces are available on the SI3226-E-GQ?
The SI3226-E-GQ uses GCI, PCM, and SPI interfaces. The product listing identifies these interfaces for connecting the integrated telecom functions to surrounding digital control logic. PCM carries the voice samples, while GCI and SPI support control and configuration traffic within the wider line-card or Voice over IP system architecture.
What package does the SI3226-E-GQ use?
The SI3226-E-GQ is packaged in a 64-pin TQFP measuring 10 x 10 mm. The package description appears in the SI3226-E-GQ distributor specification and the Si3226x product family information. Use the manufacturer's package drawing, land pattern, and pin-description table when assigning PCB pads and signals.
Where can I download the SI3226-E-GQ datasheet PDF?
The official SI3226x information is available from the Skyworks product page linked on this page, while an indexed SI3226 datasheet is also available from Silicon Laboratories. Begin with the manufacturer Si3226x page for the authoritative family documentation, then verify the ordering code, package drawing, revision, electrical limits, and pin functions before releasing a design.
Where can I find the SI3226-E-GQ pinout?
The SI3226-E-GQ pinout is defined in the pin-description table of the SI3226 family datasheet and the 64-lead package drawing. Because the catalog snippet confirms a 64-pin TQFP but does not expose the individual terminal names, use the manufacturer pin table when assigning every PCB net rather than inferring positions from the package outline.
Is the SI3226-E-GQ suitable for Voice over IP equipment?
Yes, the SI3226-E-GQ is suitable for Voice over IP endpoint and gateway designs requiring analog telephone-line interfaces. Its two integrated FXS channels, 3.3 V operation, PCM interface, and integrated CODEC support the conversion path between analog subscriber lines and a digital voice processor. Confirm line parameters and regional network requirements before deployment.
Can SI3226-E-FQ replace the SI3226-E-GQ?
SI3226-E-FQ is the closest identified drop-in candidate because both devices are listed in the same 64-pin TQFP, 10 x 10 mm package family. The available records do not expose every electrical parameter, so engineers must compare ordering codes, temperature limits, lead finish, and lifecycle status before treating the substitution as approved for production.
What is the best drop-in replacement for the SI3226-E-GQ?
No alternative can be confirmed as a production-approved drop-in replacement from the available documentation alone. SI3226-E-FQ is the only explicitly identified same-package family candidate, with a provisional 90% parameter match. Final approval requires a pin-by-pin comparison against the current manufacturer datasheet and confirmation of electrical, temperature, qualification, and lifecycle requirements.
SI3226-E-GQ versus SI3226-E-FQ: which should be selected?
Choose the SI3226-E-GQ when its exact ordering-code requirements match the design; consider SI3226-E-FQ only after its complete ordering information is verified. Both are documented in the 64-pin TQFP, 10 x 10 mm package family, but the available records do not establish whether the FQ suffix changes temperature grade, lead finish, or another ordering attribute.
When should I choose the SI3226-E-GQ over another dual-channel SLIC?
Choose the SI3226-E-GQ when the design needs two integrated FXS channels, a 3.3 V supply, CODEC functionality, and a 64-pin TQFP implementation. It is particularly useful when reducing the number of separate line-interface devices is important. Select another device when its line current, codec resolution, protection features, clocking, or thermal rating better matches the target network.
Is SI3226-E-GQ the same as a generic dual-channel SLIC?
No. The SI3226-E-GQ is a specific integrated ProSLIC implementation with two FXS channels, CODEC functionality, dual DC-DC controllers, a 3.3 V supply, and GCI, PCM, and SPI interfaces. A generic dual-channel SLIC cannot be treated as interchangeable unless its exact pinout, timing, line-drive requirements, and electrical characteristics match this device.
How do I request the current price and lead time for SI3226-E-GQ?
Use the Request a Quote form on this page to request the current price, stock status, minimum order quantity, and production lead time for the SI3226-E-GQ. The device's lifecycle status and supply can change, so obtain a written quote and schedule confirmation before committing a bill of materials or building a scheduled production plan.
Where should I buy the SI3226-E-GQ?
Use the Request a Quote form on this page to request the SI3226-E-GQ by exact MPN. Include your required quantity, packaging preference, target date, and quality-document requirements. This preserves the exact ordering code and gives purchasing teams a single request path for commercial availability rather than substituting an unverified variant.
What are the key specifications engineers should know about the SI3226-E-GQ?
The key SI3226-E-GQ specifications are two integrated FXS channels, a 3.3 V operating supply, GCI, PCM, and SPI interfaces, integrated CODEC and dual DC-DC controller functions, and a 64-pin 10 x 10 mm TQFP package. According to Skyworks product information, the device consolidates two complete telephony interfaces into one package. Line current, clocking, codec resolution, and thermal limits require confirmation in the datasheet.

داده‌های مرجع مهندسی برای SI3226-E-GQ — مقایسه، راهنمای طراحی و اطلاعات انطباق.

راهنمای انتخاب

Choose the SI3226-E-GQ when a design requires two complete analog FXS interfaces, integrated voice-codec conversion, dual DC-DC controller resources, and a compact 64-pin TQFP implementation. Its 3.3 V operation, PCM path, and documented GCI and SPI connectivity suit Voice over IP terminals, gateways, CPE, and line-card modules where component count and channel density matter. SI3226-E-FQ is the closest identified same-package candidate, but it should be selected only after its ordering-code attributes, electrical limits, temperature range, and lifecycle status have been checked against the manufacturer documentation. If either candidate does not meet required loop current, codec resolution, protection, clocking, or isolation requirements, choose a dual-channel SLIC whose published specifications satisfy those constraints rather than forcing a package-based substitution.

مقایسه با جایگزین‌ها

پارامتر این محصول SI3226-E-FQ
Brand Skyworks Solutions Skyworks Solutions
Package 64-pin TQFP (10 x 10 mm) 64-pin TQFP (10 x 10 mm)
Device Type Dual-channel ProSLIC Dual-channel SLIC/CODEC
Number of Channels 2 channels 2 channels
Supply Voltage 3.3 V 3.3 V
Integrated Functions SLIC, CODEC, and dual DC-DC controllers SLIC/CODEC with dual DC-DC controllers
Telephony Configuration Two complete FXS interfaces Two-channel subscriber-line interface

تفاوت‌های کلیدی

  • Consolidates two complete FXS channels with CODEC and dual DC-DC controller functions (در مقابلSI3226-E-FQ)
  • Supports a clearly documented digital control interface set (در مقابلSI3226-E-FQ)
  • Operates from a modern 3.3 V supply (در مقابلSI3226-E-FQ)

یادداشت‌های طراحی

Separate the analog line-side paths from PCM, SPI, and GCI digital routing, and provide a continuous ground reference beneath the device. Keep the external line-network components and their high-energy return currents away from codec and clock inputs. Use the manufacturer reference layout to establish component placement, copper geometry, and via placement rather than relying only on the 10 x 10 mm package outline.

Design the 3.3 V rail around transient and thermal requirements rather than steady-state current alone. Place required bypass capacitors adjacent to the relevant supply pins with very short ground returns, and account for the load presented by two active line channels and their DC-DC controllers. Validate startup, shutdown, line seizure, and ringing conditions on hardware because activity patterns can change rail demand beyond nominal operating load.

Do not treat the GQ and FQ ordering codes as interchangeable without checking the manufacturer's ordering guide. Confirm the exact temperature grade, lead finish, packing form, and lifecycle designation, then perform a pin-by-pin and function-by-function comparison against the current datasheet. A shared package outline alone does not establish regulatory, temperature, or production suitability.

Evaluate junction temperature with both line channels active, ringing present, and the highest supported ambient condition. The 64-pin TQFP requires adequate copper around its thermal lands and a PCB stackup that supports the manufacturer's thermal assumptions. Use the datasheet thermal model for final qualification; board-area and airflow choices materially affect the available temperature margin.

اطلاعات انطباق

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
بدون سرب
Yes
بدون هالوژن
Unknown
مواد معدنی درگیری
Unknown

The available listing identifies the related GQR variant as lead-free. RoHS, REACH, halogen-free, and conflict-minerals status for the exact SI3226-E-GQ ordering code are not established by the available records.

تاریخ تأیید داده‌ها: 2026-11-20 — داده‌ها توسط تیم مهندسی قطعات XAIPART تأیید و گردآوری شده است

جستجوهای مرتبط

SI3226-E-GQ datasheet SI3226-E-GQ pinout SI3226-E-GQ datasheet pdf SI3226-E-GQ specifications SI3226-E-GQ equivalent SI3226-E-GQ replacement SI3226-E-GQ cross reference SI3226-E-GQ vs SI3226-E-FQ SI3226-E-GQ 64 TQFP SI3226-E-GQ price SI3226-E-GQ stock Skyworks SI3226-E-GQ

قطعات و اصطلاحات مرتبط

Skyworks Solutions Silicon Laboratories SI3226-E-GQ SI3226-E-FQ SI3226-E-GQR ProSLIC subscriber line interface circuit SLIC CODEC foreign-exchange station FXS interface IC telecom interface GCI PCM SPI DC-DC controller 3.3 V power supply low-voltage CMOS 64-pin TQFP TQFP package family surface-mount package Voice over IP line-card equipment customer premises equipment
استعلام قیمت سریع RFQ
جزئیات کامل را پر کنید — تیم فروش ما ظرف 24 ساعت پاسخ خواهد داد
شماره قطعه سازنده بسته‌بندی QTY قیمت هدف قیمت کل
✓
استعلام قیمت ارسال شد!

ظرف ۲۴ ساعت به ایمیل شما پاسخ خواهیم داد

1
درخواست قیمت ارسال شد
2
استعلام دریافت شد
3
سفارش ثبت شد
4
پرداخت
5
ارسال شد
6
تحویل داده شد
مشاهده جزئیات RFQ