SN74LS393D - Dual 4-Bit Binary Counter | Texas Instruments
N.º de pieza: SN74LS393D ✓ ActivoSN74LS393D Descripción general
A binary counter is a sequential logic component that records the number of clock transitions applied to its clock input. The SN74LS393 belongs to the broader hierarchy of counter ICs, digital logic ICs, and TTL-compatible semiconductors. Its four parallel output bits provide simultaneous access to divide-by-2, divide-by-4, divide-by-8, and divide-by-16 timing signals, while two counters in one package conserve board area in digital control, instrumentation, and industrial timing systems.
The key features of the SN74LS393D include two independently clocked 4-bit binary counters, direct parallel clear, and parallel counter-stage outputs. Each half uses master-slave flip-flop stages, with the last three stages operating in a ripple sequence. This architecture is appropriate when predictable count-state visibility is more important than synchronous carry propagation. The manufacturer identifies the device as a 2-element, 4-bit, negative-edge binary counter in a 14-pin SOIC package.
The SN74LS393D is part of the 74LS TTL logic family and is suited to systems using 5 V-compatible digital interfaces. Because the counters include parallel outputs from each stage, a single output can be selected as the required submultiple of the input frequency. Cascading two internal counters also provides a total divide-by-256 capability when the external connection and counting sequence are designed according to the manufacturer documentation. The clear inputs allow the counting state to be reset during initialization or controlled system events.
Typical applications include digital time-base generation, event and pulse counting, frequency division, programmable timing modules, industrial control interfaces, and test equipment. In each case, the two counters can operate independently on separate clock inputs or be cascaded when a longer count sequence is required. The parallel outputs make the device useful in systems requiring multiple derived timing signals rather than only a serial carry or terminal-count indication.
When laying out the circuit, route the clock input away from output-return paths and use a ground reference that follows the device pin assignments in the manufacturer datasheet. Keep output loads within the specified fan-out and avoid treating ripple transitions as simultaneous events. For a new board, verify that the 14-pin SOIC footprint, pin-one orientation, supply voltage, and operating limits match the intended TTL logic environment before assembly.
This page consolidates the device function, verified distributor references, source-backed specifications, drop-in sourcing information, and practical design considerations. It also distinguishes documented electrical attributes from parameters that require confirmation in the full manufacturer datasheet, helping engineers shorten component selection and PCB implementation time.
Alternativas directas para SN74LS393D — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
SN74LS393D
✅ Sustitución directaConsulte el precio
Ver hoja de datos →SN74LS393D Valores máximos y características eléctricas
| Counter Type | Binary ripple counter |
| Number of Counters | 2 counters |
| Bits per Counter | 4 bits |
| Counting Sequence | Modulo-16 binary |
| Clock Edge | Negative edge |
| Clock Inputs | 2 independent clock inputs |
| Clear Inputs | 2 direct clear inputs |
| Configuración de salida | 4 parallel outputs per counter |
| Internal Flip-Flops | 8 master-slave flip-flops |
| Cascade Divide Ratio | Divide-by-256 |
| Logic Family | 74LS TTL |
| Encapsulado | 14-pin SOIC |
| Tipo de montaje | Surface mount |
Guía de configuración de pines de SN74LS393D 14-pin soic
Configuración de pines para SN74LS393D (encapsulado 14-pin soic). Este CI digital incluye GPIO, interfaces de comunicación (UART, SPI, I2C) y pines de alimentación. Consulte la hoja de datos del fabricante para conocer las funciones alternativas de los pines y las opciones de configuración. Esencial para el diseño de sistemas embebidos y el diseño de PCB.
No hay datos detallados de patillaje disponibles para SN74LS393D.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
SN74LS393D es adecuado para 6 aplicacións: Digital Frequency Divider, Event and Pulse Counter, Programmable Time-Base Generator, Industrial Sequence Controller, Test and Measurement Instrumentation, Digital Clock and Watch Circuit.
Digital Frequency Divider
The SN74LS393D fits frequency-divider designs because each 4-bit counter exposes parallel outputs for divide-by-2, divide-by-4, divide-by-8, and divide-by-16 ratios. A designer can route the input pulse train to a clock pin and select the required stage as a stable timing reference without adding a binary decoder. The two internal counters allow two divisions to be generated independently, while the negative-edge trigger gives the circuit a defined count transition. Because the stages ripple, output changes are sequential rather than perfectly simultaneous, so the selected output must be used in a way that tolerates normal counter propagation delay.
Recomendado
Event and Pulse Counter
The SN74LS393D can count external events by applying each event as a clock transition to one of its two clock inputs. Its 4-bit parallel outputs make the current event count directly available to control logic, while the direct clear input allows the count to be reset after a measurement interval. Using both halves provides two independent measurement channels for line-cycle, motion, or production-event monitoring. The design must account for the negative-edge counting behavior, contact or signal conditioning at the input, and the sequential propagation between internal ripple stages when determining how quickly a decoded count may be sampled.
Recomendado
Programmable Time-Base Generator
The SN74LS393D supports time-base generation by counting a periodic reference clock and selecting one of four parallel stage outputs as the derived timing signal. Two counters in the same 14-pin SOIC can produce separate base intervals or can be cascaded when a larger division is needed. The divide-by-256 capability described for the counter family is useful for slow system-timing or sequencing functions. Choose the output ratio and cascade arrangement so that ripple-stage timing remains acceptable, and provide suitable clock conditioning if the reference source can have irregular edges or excessive noise.
Recomendado
Industrial Sequence Controller
The SN74LS393D can serve as a compact state-counting element in an industrial sequence controller because each half supplies four visible count states and an independent clear input. The counter output can represent a timing interval, while additional logic determines which transition advances or resets the sequence. Two counters can monitor two stages of a machine cycle without requiring separate packages. For robust industrial use, verify the device's specified supply and temperature limits, provide clean clock signals, and avoid treating simultaneously changing ripple outputs as a single zero-delay event.
Recomendado
Test and Measurement Instrumentation
The SN74LS393D is useful in test and measurement equipment for generating selectable divided clock signals or counting repetitions of a test stimulus. Four parallel outputs from each counter provide several time-base ratios for a single input, helping reduce the number of external timing dividers required. The dual-counter organization also permits one channel to count while the other generates a related reference. Instrumentation designs should evaluate output rise and fall behavior, load capacitance, and clock jitter at the selected division ratio, since a logic divider does not improve the timing quality of its input reference.
Recomendado
Digital Clock and Watch Circuit
The SN74LS393D can implement count and divide functions in a low-speed digital clock or interval timer because its four parallel outputs correspond to successive binary divisions of the input clock. One half may establish a repetitive timing interval while the other counts completed intervals for a display or control stage. The direct clear function permits initialization when timing begins. Designers should ensure that the input clock meets the device's transition and frequency requirements, and should avoid using ripple outputs without accounting for propagation delay when several bits change close together.
Recomendado
Datos de referencia de ingeniería para SN74LS393D — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | SN74LS393D |
|---|---|---|
| Brand | Texas Instruments | onsemi |
| Package | 14-pin SOIC | 14-pin SOIC - same |
| Counter Type | Binary ripple counter | Binary counter |
| Number of Counters | 2 counters | 2 counters |
| Counter Width | 4 bits per counter | 4 bits per counter |
| Counting Sequence | Modulo-16 binary | Modulo-16 binary |
| Clock Edge | Negative edge | Negative edge |
| Output Configuration | 4 parallel outputs per counter | 4 parallel outputs per counter |
| Clear Function | Separate direct clear for each counter | Separate clear for each counter |
Diferenciadores clave
- Two counters in one compact package (frente a onsemi SN74LS393D)
- Parallel access to every binary division stage (frente a onsemi SN74LS393D)
- Negative-edge counting with dedicated clear inputs (frente a onsemi SN74LS393D)
Notas de diseño
Treat the SN74LS393D as a ripple counter rather than a zero-delay synchronizer. The three final stages of each half change sequentially, so the four parallel outputs can present different transition times. Sample only outputs whose timing relationship is acceptable, or add a holding register when a downstream circuit must receive a coherent binary word. Place clock traces away from output-return paths and maintain a continuous ground reference beneath the device.
Assign the PCB footprint directly from the 14-pin SOIC connection diagram in the Texas Instruments datasheet, including the pin-one marker and device orientation. Reserve every clock, clear, and parallel output route even when the initial design uses only part of the counter. The onsemi drop-in option should not be assumed compatible until its manufacturer pinout and package drawing have been compared against the target footprint.
The counter responds to the negative clock edge, so logic that assumes positive-edge counting will behave differently. Check every signal source, reset controller, and test fixture for the correct transition polarity. Also verify that clear pulses meet the manufacturer's timing requirements and do not accidentally overlap an active clock edge in a way that produces an unintended count transition.
Información de cumplimiento
No explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration was identified in the cited product and distributor pages. AEC-Q100 is not applicable to this general-purpose logic IC.