Texas Instruments

SN74LS623N - 8-Bit 3-State Bus Transceiver | Texas Instruments

N.º de pieza: SN74LS623N ✓ Activo
20-pin PDIP Package
MOQ: 1 |

SN74LS623N Descripción general

The Texas Instruments SN74LS623N is an octal bus transceiver with one non-inverting 8-bit element and a 3-state output, housed in a 20-pin PDIP package. The device is designed for bidirectional data transfer over a shared bus, allowing eight data lines to connect to a bus only when the output-enable input places the transceiver in an active state. Its 3-state output can provide a high-impedance condition when a bus participant is not selected, helping multiple devices share common signal lines without continuously driving them.

A bus transceiver is an interface IC that combines driver and receiver functions in one package. It sits between parallel digital logic and a shared data bus, within the broader hierarchy of transceiver → interface IC → digital IC → semiconductor. Unlike a general-purpose buffer or logic gate, a bus transceiver includes directional control and an output-enable mechanism intended to coordinate bus contention. The SN74LS623N is a non-inverting octal device, meaning the data polarity remains unchanged through the transceiver path.

The defining configuration is eight bits per element, one transceiver element, non-inverting data transfer, and a 3-state output. These features make the SN74LS623N applicable to parallel data buses, computer peripheral interfaces, memory-module connections, and industrial control systems. The 20-pin PDIP package is a through-hole format that is useful for legacy boards, prototypes, repair assemblies, and industrial equipment where surface-mount rework is impractical. Pin-level voltage limits, supply voltage range, propagation delays, and temperature limits must be confirmed in the manufacturer datasheet before production use.

The SN74LS623N belongs to the LS logic family and is identified by Texas Instruments as an octal bus transceiver. A shared-bus design requires careful control of direction and output enable so that no two enabled drivers contend on the same node. Pull-up or pull-down resistors may also be required to establish a defined state while every participant has its output disabled. Those external network requirements depend on the bus architecture and should be evaluated against the complete system timing budget.

Typical uses include retrofitting legacy parallel buses, connecting two host sections through a bidirectional buffer, isolating a peripheral port during reset, and supporting controlled sharing among multiple bus masters. The device is most appropriate when the board already uses a compatible 20-pin PDIP footprint and the design can tolerate classic LS-family logic performance. For new compact products, a smaller surface-mount package may be preferable, but changing the footprint requires a PCB redesign rather than a direct substitution.

Designers should use the pin-description table and operating conditions in the manufacturer datasheet when assigning direction, enable, ground, and supply connections. Decoupling and unused input handling must follow the device-specific guidance, while any external pull resistors should be selected from the system’s rise-time and power-budget requirements. Because legacy logic can exhibit longer switching times than modern CMOS devices, timing analysis should include the complete interconnect and receiver path.

This product page organizes the device’s verified configuration, sourcing information, drop-in alternatives, application guidance, and design cautions for engineers maintaining or redesigning an older parallel-bus system. It also distinguishes confirmed interface characteristics from electrical details that must be obtained from the manufacturer datasheet, supporting faster component selection without obscuring the limits of legacy through-hole logic.

Alternativas directas para SN74LS623N — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.

No hay alternativas directas disponibles para este producto.

Solicitar alternativas

SN74LS623N Valores máximos y características eléctricas

Product Type Octal bus transceiver
Logic Family LS TTL
Number of Elements 1 element
Bits per Element 8 bits
Data Polarity Non-inverting
Output State 3-state output
Encapsulado 20-pin PDIP
Total Pin Count 20 pins
Tipo de montaje Through-hole

Guía de configuración de pines de SN74LS623N 20-pin pdip

Configuración de pines para SN74LS623N (encapsulado 20-pin pdip). Este CI digital incluye GPIO, interfaces de comunicación (UART, SPI, I2C) y pines de alimentación. Consulte la hoja de datos del fabricante para conocer las funciones alternativas de los pines y las opciones de configuración. Esencial para el diseño de sistemas embebidos y el diseño de PCB.

Diagrama de patillaje del encapsulado 20-pin pdip para SN74LS623N

No hay datos detallados de patillaje disponibles para SN74LS623N.

Consulte la hoja de datos para ver la configuración completa de patillas.

Aplicaciones típicas

SN74LS623N es adecuado para 6 aplicacións: Legacy Parallel Computer Bus, Shared Peripheral Data Port, Industrial Control Backplane, Peripheral Test Adapter, Data Acquisition Front End, Retrofit and Repair Electronics.

🖥️

Legacy Parallel Computer Bus

The SN74LS623N fits a legacy parallel-bus interface because it provides eight non-inverting lines with a 3-state output in a single 20-pin PDIP device. It can connect a processor-side bus to a shared peripheral bus when direction and output-enable signals are coordinated so that only one driver is active. Its principal advantage is the ability to place an idle driver in a high-impedance state, while the trade-off is the larger through-hole footprint and the lower performance associated with maintaining an LS-family system. Use the manufacturer timing data to verify setup, hold, and propagation requirements against the bus clock period.

🔧

Shared Peripheral Data Port

The SN74LS623N can isolate a peripheral port from a shared data bus by disabling its outputs whenever another device owns the bus. Its eight non-inverting channels and 3-state output support byte-wide data transfer, while the 20-pin PDIP package simplifies repair of older control and test equipment. Designers must define enable polarity and default states so that reset conditions cannot place multiple outputs on the same bus. External pull resistors may be required to keep the bus at a defined logic level while every transceiver is disabled.

🏭

Industrial Control Backplane

The SN74LS623N is appropriate for a legacy industrial control backplane where multiple modules exchange parallel data and must release the shared conductors between transactions. The non-inverting 8-bit path preserves data polarity, and the 3-state output permits a controlled connection to the bus. Its PDIP format supports replacement in older machinery without introducing a new surface-mount assembly process. The design should include explicit contention checks, power-budget analysis, and protection appropriate to the installation environment before the module is placed into service.

🔧

Peripheral Test Adapter

A test adapter built around the SN74LS623N can connect a legacy DUT interface to a tester while keeping unused bus directions electrically inactive. Its eight-bit non-inverting configuration simplifies byte-level connections, and the 3-state output helps prevent the DUT and tester from driving the same lines simultaneously. Through-hole packaging is useful for fixture construction and field repair. Adapter designers should verify voltage and timing compatibility with the actual tester, include current limiting where required, and avoid relying on control defaults without an external reset circuit.

📺

Data Acquisition Front End

The SN74LS623N can serve as the digital isolation boundary between a parallel sensor-conditioning or converter section and a shared acquisition bus. Its 3-state output allows the front end to disconnect from the bus while another section communicates, reducing the need for separate buffers. The non-inverting channel arrangement avoids additional polarity conversion. Because an acquisition system can present demanding timing and fan-out requirements, engineers must confirm the datasheet timing limits, bus topology, and noise behavior rather than assuming general-purpose bus compatibility.

🔧

Retrofit and Repair Electronics

The SN74LS623N is especially useful in repair and modernization of equipment designed around the 74LS logic family and a 20-pin PDIP footprint. Its confirmed octal, non-inverting, 3-state configuration matches the role described by the manufacturer, allowing a failed transceiver section to be serviced without redesigning the surrounding logic. Before installation, verify that the replacement MPN, pinout, temperature grade, and supply requirements match the failed component. Maintain good socket or solder joints and observe the manufacturer’s handling and decoupling guidance.

What is the SN74LS623N?
The SN74LS623N is a Texas Instruments octal bus transceiver containing one non-inverting 8-bit transceiver element with a 3-state output in a 20-pin PDIP package. According to the manufacturer datasheet, its principal role is to support controlled, bidirectional communication on shared parallel data buses while allowing an output driver to assume a high-impedance state when the bus is not selected.
What does the 3-state output of the SN74LS623N mean?
The SN74LS623N 3-state output can actively drive a logic level or enter a high-impedance condition under output-enable control. This third state lets several devices share one bus without two enabled drivers continuously competing. According to the Texas Instruments datasheet, correct use of the enable and direction controls is essential to prevent bus contention and data corruption.
Where can I download the SN74LS623N datasheet PDF?
The official SN74LS623N datasheet PDF is available from Texas Instruments at https://www.ti.com/lit/ds/symlink/sn74ls623.pdf. It is the primary reference for the 20-pin PDIP pinout, supply limits, input and output ratings, timing characteristics, enable behavior, and recommended operating conditions. The manufacturer product page at https://www.ti.com/product/SN74LS623 provides additional ordering and quality information.
Where is the SN74LS623N pinout located?
The SN74LS623N pinout is shown in the manufacturer datasheet and must be followed exactly when assigning the 20 PDIP connections. Use the datasheet pin-description table to identify supply, ground, data, direction, and output-enable functions. The 20-pin PDIP outline is also represented by the package diagram, but its package drawing does not replace the device-specific electrical pin table.
What are the key specifications of SN74LS623N that engineers should know?
The confirmed SN74LS623N configuration is one octal transceiver element with 8 bits per element, non-inverting signal transfer, a 3-state output, and a 20-pin PDIP package. It is an LS-family interface IC intended for parallel shared-bus communication. Supply voltage, propagation delay, current limits, and temperature range should be taken directly from the manufacturer datasheet before defining the system timing or power budget.
Is the SN74LS623N suitable for bidirectional parallel buses?
The SN74LS623N is suitable for bidirectional parallel-bus interfacing because it combines transmit and receive functions and provides a 3-state output for bus sharing. Its direction and output-enable inputs must be coordinated so that only one side of the interface drives a shared node at a time. The manufacturer datasheet should be used to confirm the required control-state truth table.
When should I choose the SN74LS623N over a smaller surface-mount transceiver?
Choose the SN74LS623N when the existing board uses a 20-pin PDIP footprint, through-hole repair is important, or a legacy parallel interface is being maintained. A smaller surface-mount implementation may be preferable for new compact equipment, but it is not a footprint-compatible upgrade because the PCB land pattern changes. The decision should also consider whether legacy LS-family timing satisfies the bus refresh requirements.
What can replace the SN74LS623N?
A true replacement for the SN74LS623N must use the same 20-pin PDIP footprint, preserve the non-inverting octal transceiver function, and provide compatible direction and output-enable behavior. No confirmed pin-compatible replacement was established from the available manufacturer and cross-reference results. Before using any substitute, compare its datasheet pinout, supply range, timing, output states, and propagation delays against the original device.
Is the SN74LS623N the same as SN74LS623NG4?
SN74LS623NG4 denotes the SN74LS623 device with an ordering and green-material suffix, while SN74LS623N is the 20-pin PDIP ordering code used on this page. Their electrical suitability cannot be assumed from the suffix alone; the manufacturer ordering table must confirm package construction, temperature grade, and marking. A suffix variant is not automatically a separate drop-in replacement candidate.
SN74LS623N vs SN74LS623: which part number should be selected?
SN74LS623 identifies the underlying Texas Instruments octal bus transceiver device, while SN74LS623N is the orderable 20-pin PDIP designation. For a new board, use the full ordering MPN to avoid ambiguity about package and ordering information. For repair work, verify the installed device marking against the manufacturer ordering table before selecting a replacement.
Can SN74LS623N replace SN74LS623NG4?
SN74LS623N can serve as the ordering designation for the SN74LS623 family when its 20-pin PDIP package and required operating characteristics match the installed SN74LS623NG4 device. Because the G4 suffix can encode ordering and environmental attributes, confirm the original device marking, package, temperature grade, and datasheet limits. Do not substitute solely because both names contain SN74LS623.
Where can I buy SN74LS623N and request a quote?
Use the Request a Quote form on this page to request current SN74LS623N availability, lead time, and commercial terms. The Texas Instruments product page at https://www.ti.com/product/SN74LS623 is the authoritative source for the manufacturer’s ordering information. Current supply status and order quantities should be confirmed through the quote workflow because legacy inventory levels can change.
What is the price of SN74LS623N?
The current commercial price of SN74LS623N is not shown in static page content because legacy component pricing and availability can change by quantity and date. Use the Request a Quote form on this page for the exact unit price, volume breaks, stock position, and lead time applicable to your order. The price presented by the form will reflect the current sourcing channel rather than a historical catalog amount.
What is the lead time for SN74LS623N?
Lead time for SN74LS623N depends on current manufacturer or channel inventory, order quantity, and the selected package. Submit the required quantity through the Request a Quote form on this page for a current lead-time response. The manufacturer product page at https://www.ti.com/product/SN74LS623 is also useful for confirming ordering options and part status.
Is SN74LS623N in stock?
Stock for SN74LS623N changes as legacy inventory is allocated and replenished. Use the Request a Quote form on this page to request the current stock quantity for your required order quantity and shipment location. The Texas Instruments product page links to authorized ordering information and should be consulted when production planning depends on long-term availability.
What design checks are needed for an SN74LS623N bus interface?
The critical SN74LS623N checks include control-state sequencing, contention avoidance, input termination, supply decoupling, and timing margin. Confirm the manufacturer’s truth table so that direction and output-enable signals never leave opposing drivers active simultaneously. Evaluate bus pull-up or pull-down values against the desired inactive voltage, power budget, and maximum transition time, then include board capacitance in the timing analysis.

Datos de referencia de ingeniería para SN74LS623N — comparación, orientación de diseño e información de cumplimiento.

Guía de selección

Choose the SN74LS623N when maintaining or designing a legacy parallel system that specifically requires one octal, non-inverting transceiver element with a 3-state output and a 20-pin PDIP footprint. It is a practical fit for controlled shared-bus communication, peripheral isolation, and industrial repair assemblies where through-hole replacement is important. Do not select it merely because another 74-series buffer performs a similar data function; direction controls, output-enable polarity, timing, and supply requirements must match. For a new compact product, a modern surface-mount transceiver may offer a smaller footprint and better performance, although that change requires a PCB redesign. Before ordering any replacement, verify the manufacturer pinout, control truth table, electrical limits, and operating-temperature grade rather than relying only on the base family name.

Comparación con alternativas

Parámetro Este producto
Manufacturer Texas Instruments
Package 20-pin PDIP
Product Type Octal bus transceiver
Number of Elements 1 element
Bits per Element 8 bits
Data Polarity Non-inverting
Output State 3-state output
Logic Family LS TTL
Mounting Type Through-hole

Diferenciadores clave

  • Eight-bit non-inverting bus interface in one package (frente a Single-channel buffer implementations)
  • Controlled high-impedance bus state (frente a Always-driving transceiver implementations)
  • Compatible with legacy through-hole PCB architecture (frente a Surface-mount transceiver implementations)

Notas de diseño

Treat direction and output-enable sequencing as a safety-critical interface issue. Use the manufacturer control truth table to prevent two enabled drivers from driving the same bus node simultaneously, including during reset or power transitions. Define fail-safe states in hardware where a floating control input could create contention, and validate every operating mode rather than only the normal transmit and receive states.

Use the 20-pin PDIP footprint only when it matches the existing board mechanically and electrically. Place the device where through-hole replacement remains practical, and route the shared-bus traces away from sensitive analog or high-speed signals. Maintain compact supply connections and follow the manufacturer’s decoupling recommendations so switching currents on the logic rail do not add avoidable noise to adjacent circuitry.

Analyze the complete bus rather than only the transceiver output. Include cable or PCB capacitance, receiver input loading, pull-resistor impedance, and the receiver’s timing limits when calculating rise time and setup margin. A 3-state output removes active drive, but it does not prevent a floating bus from producing undefined transitions, so pull-up or pull-down resistors may still be necessary.

Información de cumplimiento

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Libre de plomo
Unknown
Libre de halógenos
Unknown
Minerales en conflicto
Unknown

The available product information does not establish the requested compliance attributes. SN74LS623N is a general-purpose logic device and is not presented as an automotive-qualified AEC-Q100 variant.

Búsquedas relacionadas

SN74LS623N datasheet SN74LS623N datasheet pdf SN74LS623N pinout SN74LS623N pin configuration SN74LS623N 20-pin PDIP SN74LS623N octal bus transceiver SN74LS623N 3-state output SN74LS623N equivalent SN74LS623N replacement SN74LS623N cross reference Texas Instruments SN74LS623N SN74LS623N price SN74LS623N stock SN74LS623N application circuit SN74LS623 vs SN74LS623N

Componentes & términos relacionados

Texas Instruments SN74LS623 SN74LS623N SN74LS623NG4 Octal bus transceiver Bus transceiver Transceiver Interface IC Logic IC Digital IC Semiconductor LS TTL 74LS logic family Non-inverting logic 3-state output High-impedance output Bidirectional data bus Parallel data bus Output enable Direction control 20-pin PDIP DIP package Through-hole package MC74F243M MC74F538N
RFQ de presupuesto rápido
Complete los detalles — nuestro equipo de ventas responderá en un plazo de 24 horas
Número de pieza Fabricante Encapsulado QTY Precio objetivo Total
✓
¡Presupuesto enviado!

Responderemos a su correo electrónico en un plazo de 24 horas

1
RFQ enviado
2
Presupuesto recibido
3
Pedido realizado
4
Pago
5
Enviado
6
Entregado
Ver detalles del RFQ