SN74LS623N - 8-Bit 3-State Bus Transceiver | Texas Instruments
MPN: SN74LS623N ✓ פעילSN74LS623N סקירה
A bus transceiver is an interface IC that combines driver and receiver functions in one package. It sits between parallel digital logic and a shared data bus, within the broader hierarchy of transceiver → interface IC → digital IC → semiconductor. Unlike a general-purpose buffer or logic gate, a bus transceiver includes directional control and an output-enable mechanism intended to coordinate bus contention. The SN74LS623N is a non-inverting octal device, meaning the data polarity remains unchanged through the transceiver path.
The defining configuration is eight bits per element, one transceiver element, non-inverting data transfer, and a 3-state output. These features make the SN74LS623N applicable to parallel data buses, computer peripheral interfaces, memory-module connections, and industrial control systems. The 20-pin PDIP package is a through-hole format that is useful for legacy boards, prototypes, repair assemblies, and industrial equipment where surface-mount rework is impractical. Pin-level voltage limits, supply voltage range, propagation delays, and temperature limits must be confirmed in the manufacturer datasheet before production use.
The SN74LS623N belongs to the LS logic family and is identified by Texas Instruments as an octal bus transceiver. A shared-bus design requires careful control of direction and output enable so that no two enabled drivers contend on the same node. Pull-up or pull-down resistors may also be required to establish a defined state while every participant has its output disabled. Those external network requirements depend on the bus architecture and should be evaluated against the complete system timing budget.
Typical uses include retrofitting legacy parallel buses, connecting two host sections through a bidirectional buffer, isolating a peripheral port during reset, and supporting controlled sharing among multiple bus masters. The device is most appropriate when the board already uses a compatible 20-pin PDIP footprint and the design can tolerate classic LS-family logic performance. For new compact products, a smaller surface-mount package may be preferable, but changing the footprint requires a PCB redesign rather than a direct substitution.
Designers should use the pin-description table and operating conditions in the manufacturer datasheet when assigning direction, enable, ground, and supply connections. Decoupling and unused input handling must follow the device-specific guidance, while any external pull resistors should be selected from the system’s rise-time and power-budget requirements. Because legacy logic can exhibit longer switching times than modern CMOS devices, timing analysis should include the complete interconnect and receiver path.
This product page organizes the device’s verified configuration, sourcing information, drop-in alternatives, application guidance, and design cautions for engineers maintaining or redesigning an older parallel-bus system. It also distinguishes confirmed interface characteristics from electrical details that must be obtained from the manufacturer datasheet, supporting faster component selection without obscuring the limits of legacy through-hole logic.
חלופות תחליף ישיר עבור SN74LS623N — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
אין חלופות תואמות Drop-in עבור מוצר זה.
בקשת חלופותSN74LS623N דירוגים מרביים ומאפיינים חשמליים
| Product Type | Octal bus transceiver |
| Logic Family | LS TTL |
| Number of Elements | 1 element |
| Bits per Element | 8 bits |
| Data Polarity | Non-inverting |
| Output State | 3-state output |
| מארז | 20-pin PDIP |
| Total Pin Count | 20 pins |
| סוג הרכבה | Through-hole |
מדריך תצורת פינים של SN74LS623N 20-pin pdip
תצורת פינים עבור SN74LS623N (מארזת 20-pin pdip). מעגל משולב דיגיטלי זה כולל GPIO, ממשקי תקשורת (UART, SPI, I2C) ופיני מתח. יש לעיין בגיליון הנתונים של היצרן לפונקציות פינים חלופיות ולאפשרויות תצורה. חיוני לתכנון מערכות משובצות ולפריסת PCB.
אין נתוני פריסת פינים מפורטים עבור SN74LS623N.
עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.
יישומים טיפוסיים
SN74LS623N מתאים עבור 6 יישוםs: Legacy Parallel Computer Bus, Shared Peripheral Data Port, Industrial Control Backplane, Peripheral Test Adapter, Data Acquisition Front End, Retrofit and Repair Electronics.
Legacy Parallel Computer Bus
The SN74LS623N fits a legacy parallel-bus interface because it provides eight non-inverting lines with a 3-state output in a single 20-pin PDIP device. It can connect a processor-side bus to a shared peripheral bus when direction and output-enable signals are coordinated so that only one driver is active. Its principal advantage is the ability to place an idle driver in a high-impedance state, while the trade-off is the larger through-hole footprint and the lower performance associated with maintaining an LS-family system. Use the manufacturer timing data to verify setup, hold, and propagation requirements against the bus clock period.
מומלץ
Shared Peripheral Data Port
The SN74LS623N can isolate a peripheral port from a shared data bus by disabling its outputs whenever another device owns the bus. Its eight non-inverting channels and 3-state output support byte-wide data transfer, while the 20-pin PDIP package simplifies repair of older control and test equipment. Designers must define enable polarity and default states so that reset conditions cannot place multiple outputs on the same bus. External pull resistors may be required to keep the bus at a defined logic level while every transceiver is disabled.
מומלץ
Industrial Control Backplane
The SN74LS623N is appropriate for a legacy industrial control backplane where multiple modules exchange parallel data and must release the shared conductors between transactions. The non-inverting 8-bit path preserves data polarity, and the 3-state output permits a controlled connection to the bus. Its PDIP format supports replacement in older machinery without introducing a new surface-mount assembly process. The design should include explicit contention checks, power-budget analysis, and protection appropriate to the installation environment before the module is placed into service.
מומלץ
Peripheral Test Adapter
A test adapter built around the SN74LS623N can connect a legacy DUT interface to a tester while keeping unused bus directions electrically inactive. Its eight-bit non-inverting configuration simplifies byte-level connections, and the 3-state output helps prevent the DUT and tester from driving the same lines simultaneously. Through-hole packaging is useful for fixture construction and field repair. Adapter designers should verify voltage and timing compatibility with the actual tester, include current limiting where required, and avoid relying on control defaults without an external reset circuit.
מומלץ
Data Acquisition Front End
The SN74LS623N can serve as the digital isolation boundary between a parallel sensor-conditioning or converter section and a shared acquisition bus. Its 3-state output allows the front end to disconnect from the bus while another section communicates, reducing the need for separate buffers. The non-inverting channel arrangement avoids additional polarity conversion. Because an acquisition system can present demanding timing and fan-out requirements, engineers must confirm the datasheet timing limits, bus topology, and noise behavior rather than assuming general-purpose bus compatibility.
מומלץ
Retrofit and Repair Electronics
The SN74LS623N is especially useful in repair and modernization of equipment designed around the 74LS logic family and a 20-pin PDIP footprint. Its confirmed octal, non-inverting, 3-state configuration matches the role described by the manufacturer, allowing a failed transceiver section to be serviced without redesigning the surrounding logic. Before installation, verify that the replacement MPN, pinout, temperature grade, and supply requirements match the failed component. Maintain good socket or solder joints and observe the manufacturer’s handling and decoupling guidance.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור SN74LS623N — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה |
|---|---|
| Manufacturer | Texas Instruments |
| Package | 20-pin PDIP |
| Product Type | Octal bus transceiver |
| Number of Elements | 1 element |
| Bits per Element | 8 bits |
| Data Polarity | Non-inverting |
| Output State | 3-state output |
| Logic Family | LS TTL |
| Mounting Type | Through-hole |
מבדילים עיקריים
- Eight-bit non-inverting bus interface in one package (לעומתSingle-channel buffer implementations)
- Controlled high-impedance bus state (לעומתAlways-driving transceiver implementations)
- Compatible with legacy through-hole PCB architecture (לעומתSurface-mount transceiver implementations)
הערות תכנון
Treat direction and output-enable sequencing as a safety-critical interface issue. Use the manufacturer control truth table to prevent two enabled drivers from driving the same bus node simultaneously, including during reset or power transitions. Define fail-safe states in hardware where a floating control input could create contention, and validate every operating mode rather than only the normal transmit and receive states.
Use the 20-pin PDIP footprint only when it matches the existing board mechanically and electrically. Place the device where through-hole replacement remains practical, and route the shared-bus traces away from sensitive analog or high-speed signals. Maintain compact supply connections and follow the manufacturer’s decoupling recommendations so switching currents on the logic rail do not add avoidable noise to adjacent circuitry.
Analyze the complete bus rather than only the transceiver output. Include cable or PCB capacitance, receiver input loading, pull-resistor impedance, and the receiver’s timing limits when calculating rise time and setup margin. A 3-state output removes active drive, but it does not prevent a floating bus from producing undefined transitions, so pull-up or pull-down resistors may still be necessary.
מידע על תאימות
The available product information does not establish the requested compliance attributes. SN74LS623N is a general-purpose logic device and is not presented as an automotive-qualified AEC-Q100 variant.