SN74LS645N - 8-Bit 3-State Bus Transceiver | Texas Instruments
N.º de pieza: SN74LS645N ✓ ActivoSN74LS645N Descripción general
An octal bus transceiver is a bidirectional interface IC that combines a bus driver, receiver, and direction-control logic in one package. Within the broader hierarchy of interface ICs, it supports the 74LS bipolar logic family and the TTL-compatible 5 V system environment. Its eight parallel channels make it suitable for routing byte-wide data among processor, memory, peripheral, and backplane interfaces without requiring eight separate single-channel transceivers.
The main features include non-inverting data transfer, 3-state output control, eight independently usable I/O paths, and Schmitt-trigger input behavior. The Schmitt trigger helps improve noise tolerance by providing hysteresis at the input threshold. The 3-state output can actively drive a logic high or low, or present a high-impedance state when disabled, allowing several devices to share a bus when only one driver is enabled at a time. The 20-pin PDIP format also supports conventional through-hole assembly and prototyping.
Technically, the SN74LS645N combines directional control with bus-state management. Direction and output-enable inputs determine whether data flows from the A-side bus to the B-side bus, from B to A, or remains disabled at the outputs. Because this is a bipolar 74LS-family device, designers should account for the logic levels, transition timing, fanout, and supply tolerances associated with that family rather than treating it as a modern low-voltage CMOS bus device.
Typical uses include bidirectional eight-bit CPU and peripheral buses, data multiplexers, test equipment, memory-interface routing, and industrial control boards. In each case, the transmitter is useful where two bus masters or independent subsystems must exchange byte-wide data while retaining tri-state control over bus ownership. The SN74LS645N is most appropriate when legacy 5 V TTL signaling, through-hole construction, and established 74LS interoperability are priorities.
During layout, keep the data paths short and route the eight corresponding A and B signals as matched groups. Place decoupling close to the supply pins, provide a common ground reference, and confirm that enable and direction timing does not create contention. This page combines verified product attributes, documented replacement options, and practical bus-interface design guidance for faster component selection.
Alternativas directas para SN74LS645N — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con SN74LS645N (mismo factor de forma y huella) — difiere en Logic Family, Output State.
SN74LS645-1N
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
SN74LS645N Especificaciones
| Device Type | Octal bus transceiver |
| Logic Family | 74LS bipolar TTL |
| Number of Elements | 1 element |
| Bits per Element | 8 bits |
| Data Direction | Non-inverting |
| Output State | 3-state |
| Supply Voltage Range | 4.75 V to 5.25 V |
| Input Type | Schmitt trigger |
| Output Sink Current | 15 mA |
| Bus Communication | Asynchronous two-way |
| Encapsulado | 20-pin PDIP |
| Total Pin Count | 20 pins |
| Tipo de montaje | Through-hole |
Guía de configuración de pines de SN74LS645N 20-pin pdip
Configuración de pines para SN74LS645N (encapsulado 20-pin pdip). La numeración de pines, las funciones y los diagramas de conexión se definen en la hoja de datos del fabricante. Consúltela para conocer el footprint exacto y las directrices de soldadura.
No hay datos detallados de patillaje disponibles para SN74LS645N.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
SN74LS645N es adecuado para 6 aplicacións: Bidirectional CPU Bus Interface, Industrial Control Data Routing, Memory and Peripheral Bus Multiplexing, Legacy Test and Measurement Systems, Printer and Peripheral Data Sharing, Embedded 5 V System Interconnect.
Bidirectional CPU Bus Interface
The SN74LS645N fits legacy 8-bit processor buses that need controlled data transfer in both directions. Eight parallel, non-inverting channels carry byte-wide information between a CPU-side bus and a peripheral-side bus, while the 3-state outputs can disconnect the device when it does not own the shared conductor. Its 4.75 V to 5.25 V operating range targets 5 V TTL systems, and the Schmitt-trigger inputs improve threshold behavior in environments where bus edges may be influenced by noise. Because contention can damage outputs, the external control logic must ensure that only one driver enables the shared bus at a time and that direction changes respect the device’s timing requirements.
Recomendado
Industrial Control Data Routing
The SN74LS645N is useful in industrial control boards that route byte-wide sensor, actuator, and controller signals between subsystem backplanes. The device’s 20-pin PDIP package is practical for through-hole control hardware, while its eight channels reduce the number of discrete transceivers required for grouped data paths. The 3-state output supports shared-bus arbitration when the controller disables the transceiver outside its active interval. Designers should use a single common ground, terminate signals consistently, and verify timing margins for the control board’s processor and peripheral clocking. Its 5 V supply window and 15 mA sink capability align with conventional 74LS logic rather than low-voltage CMOS interfaces.
Recomendado
Memory and Peripheral Bus Multiplexing
The SN74LS645N can provide directional routing between a processor bus and a memory or peripheral interface when both sides use compatible 5 V logic. Byte-wide operation allows eight related signals to change direction together, simplifying address, data, or command multiplexing where multiple resources share conductors. The non-inverting paths preserve signal polarity, and the tri-state outputs let the system isolate the device when another resource becomes the active bus owner. Timing remains the principal design constraint: enable and direction controls must not overlap in a way that creates output contention, and the source and destination devices must maintain compatible rise, fall, and propagation timing.
Recomendado
Legacy Test and Measurement Systems
The SN74LS645N suits legacy test equipment that needs to route eight measurement or control lines between an instrument bus and a device under test. Its bidirectional non-inverting channels accommodate both command transfer and response capture, while the high-impedance output state allows the instrument bus to be shared safely under controlled ownership. The through-hole PDIP package supports repair-oriented and prototype assemblies, and the Schmitt-trigger inputs are beneficial when slower or noisier test-bus wiring is involved. Engineers should add appropriate pull resistors where required by the system architecture and verify that the DUT cannot drive a bus line while the transceiver is actively driving it.
Recomendado
Printer and Peripheral Data Sharing
The SN74LS645N can support a shared peripheral data path in older printer, terminal, or controller assemblies where one bus must connect to more than one 8-bit peripheral. Direction control determines whether commands travel toward the peripheral or data returns toward the controller, and the 3-state output lets each transceiver release the bus when inactive. This arrangement reduces duplicated logic while retaining legacy 74LS interoperability. The implementation must include a deterministic arbitration mechanism to prevent two peripherals from driving simultaneously. Cable or board-trace loading, grounding, and logic thresholds should be evaluated before adding long interconnects, since a 5 V TTL bus transceiver is generally better suited to controlled board-level communication than long-distance cabling.
Recomendado
Embedded 5 V System Interconnect
The SN74LS645N is appropriate for embedded systems that retain a 5 V TTL control domain alongside older memory, display, or expansion hardware. Eight non-inverting channels provide a compact bridge between the embedded controller and a legacy bus without requiring individual buffer packages for every line. The Schmitt-trigger input characteristic provides defined switching behavior, while the 3-state output supports isolation from other bus participants. The SN74LS645N should be powered from a properly decoupled 5 V rail and referenced to the same ground network as the connected devices. Designers must also account for direction-control timing and ensure that any attached device remains high-impedance while the transceiver is driving the corresponding bus.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para SN74LS645N — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | SN74LS645-1N |
|---|---|---|
| Package | 20-pin PDIP | 20-pin PDIP |
| Brand | Texas Instruments | Texas Instruments |
| Function | Octal bus transceiver | Octal bus transceiver |
| Number of Channels | 8 bits | 8 bits |
| Data Direction | Non-inverting | Non-inverting |
| Output State | 3-state | 3-state |
| Supply Voltage | 4.75 V to 5.25 V | 4.75 V to 5.25 V |
| Input Type | Schmitt trigger | Schmitt trigger |
| Output Sink Current | 15 mA | 15 mA |
Diferenciadores clave
- Exact 20-pin PDIP replacement path (frente a SN74LS645-1N)
- Eight parallel bidirectional channels (frente a SN74LS245N)
- Compatible 5 V interface environment (frente a SN74LS640N)
Notas de diseño
Never allow two 74LS bus drivers to enable the same shared line simultaneously. Output contention can produce excessive current and undefined voltage levels even when the data inputs agree. Use the enable and direction controls so that ownership changes only after the previous driver has entered its 3-state interval, and include the relevant timing limits from the manufacturer datasheet in the system timing budget.
Place the supply bypass capacitor close to the transceiver’s supply pins and connect it to a low-impedance ground plane. Keep the eight A-side and B-side routes physically compact, and route the corresponding pairs with similar geometry to limit skew between byte lanes. In through-hole designs, minimize stub branches from the shared bus because excessive loading can reduce noise margin and upset the 74LS timing budget.
Use the Schmitt-trigger input characteristic to improve tolerance of slow or noisy transitions, but do not treat it as a substitute for sound signal-integrity design. Maintain a common ground reference between communicating devices, avoid long unterminated branches, and verify rise-time, propagation-delay, and setup requirements at the actual bus clock rate. The manufacturer datasheet should govern any termination values and timing assumptions.
The SN74LS645N is intended for a 4.75 V to 5.25 V operating range, so the system should provide a stable 5 V rail rather than an unregulated source. Check the supply ramp, noise, and ground-return paths, especially when the transceiver is enabled during system startup. Confirm device-specific current and absolute-maximum limits in the complete manufacturer documentation before adding external loading.
Información de cumplimiento
The manufacturer product page and component listings do not state the requested compliance certifications. AEC-Q100 is not applicable to this general-purpose 74LS logic device.