Texas Instruments

SN74LS645N - 8-Bit 3-State Bus Transceiver | Texas Instruments

MPN: SN74LS645N ✓ Aktif
4.75 V to 5.25 V Vdss 15 mA Id 20-pin PDIP Package
MOQ: 1 |

SN74LS645N Ringkasan

Texas Instruments SN74LS645N is an 8-bit, non-inverting, 3-state bus transceiver with a 20-pin PDIP package. It operates from a 4.75 V to 5.25 V supply, supports asynchronous two-way communication between data buses, and includes Schmitt-trigger inputs with a 15 mA sink capability. The device is designed for systems that need to place one side of an eight-bit data path into a high-impedance state so that multiple bus drivers can share a common conductor.

An octal bus transceiver is a bidirectional interface IC that combines a bus driver, receiver, and direction-control logic in one package. Within the broader hierarchy of interface ICs, it supports the 74LS bipolar logic family and the TTL-compatible 5 V system environment. Its eight parallel channels make it suitable for routing byte-wide data among processor, memory, peripheral, and backplane interfaces without requiring eight separate single-channel transceivers.

The main features include non-inverting data transfer, 3-state output control, eight independently usable I/O paths, and Schmitt-trigger input behavior. The Schmitt trigger helps improve noise tolerance by providing hysteresis at the input threshold. The 3-state output can actively drive a logic high or low, or present a high-impedance state when disabled, allowing several devices to share a bus when only one driver is enabled at a time. The 20-pin PDIP format also supports conventional through-hole assembly and prototyping.

Technically, the SN74LS645N combines directional control with bus-state management. Direction and output-enable inputs determine whether data flows from the A-side bus to the B-side bus, from B to A, or remains disabled at the outputs. Because this is a bipolar 74LS-family device, designers should account for the logic levels, transition timing, fanout, and supply tolerances associated with that family rather than treating it as a modern low-voltage CMOS bus device.

Typical uses include bidirectional eight-bit CPU and peripheral buses, data multiplexers, test equipment, memory-interface routing, and industrial control boards. In each case, the transmitter is useful where two bus masters or independent subsystems must exchange byte-wide data while retaining tri-state control over bus ownership. The SN74LS645N is most appropriate when legacy 5 V TTL signaling, through-hole construction, and established 74LS interoperability are priorities.

During layout, keep the data paths short and route the eight corresponding A and B signals as matched groups. Place decoupling close to the supply pins, provide a common ground reference, and confirm that enable and direction timing does not create contention. This page combines verified product attributes, documented replacement options, and practical bus-interface design guidance for faster component selection.

Pilihan pengganti yang segera untuk SN74LS645N — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.

Varietas dalam siri ini

Model serupa yang kompatibel dengan pengganti yang segera SN74LS645N (sama faktor bentuk dan kaki) — berbeza dalam Logic Family, Output State.

Texas Instruments
Logic Family: 74LS low-power Schottky TTL
Output State: Three-state output
Bandingkan Dengan SN74LS645N →

SN74LS645-1N

✅ Masuk Drop-In
📦 20-pin PDIP
Same 20-pin PDIP footprint and SN74LS645 transceiver function; the published comparison identifies consistent terminals and packages, with the principal difference being the ordering or speed-grade suffix.

📋 Alternatif rujukan (tidak dalam katalog)

SN74LS645N Spesifikasi

Device Type Octal bus transceiver
Logic Family 74LS bipolar TTL
Number of Elements 1 element
Bits per Element 8 bits
Data Direction Non-inverting
Output State 3-state
Supply Voltage Range 4.75 V to 5.25 V
Input Type Schmitt trigger
Output Sink Current 15 mA
Bus Communication Asynchronous two-way
Kemasan 20-pin PDIP
Total Pin Count 20 pins
Jenis Pemasangan Through-hole

Panduan Konfigurasi Pin SN74LS645N 20-pin pdip

Konfigurasi pin untuk SN74LS645N (20-pin pdip pakai). Penomeran pin, fungsi, dan garis bentuk koneksi ditakrifkan dalam dokumen pengeluar. Rujuk dokumen untuk kebentuk dan pedoman pengasman.

Garis bentuk pengecah pakai 20-pin pdip untuk SN74LS645N

Tiada data garisan pin yang diperoleh untuk SN74LS645N.

Rujuk kepada lembaran data untuk konfigurasi pin penuh.

Aplikasi Biasa

SN74LS645N patut untuk 6 aplikasis: Bidirectional CPU Bus Interface, Industrial Control Data Routing, Memory and Peripheral Bus Multiplexing, Legacy Test and Measurement Systems, Printer and Peripheral Data Sharing, Embedded 5 V System Interconnect.

🖥️

Bidirectional CPU Bus Interface

The SN74LS645N fits legacy 8-bit processor buses that need controlled data transfer in both directions. Eight parallel, non-inverting channels carry byte-wide information between a CPU-side bus and a peripheral-side bus, while the 3-state outputs can disconnect the device when it does not own the shared conductor. Its 4.75 V to 5.25 V operating range targets 5 V TTL systems, and the Schmitt-trigger inputs improve threshold behavior in environments where bus edges may be influenced by noise. Because contention can damage outputs, the external control logic must ensure that only one driver enables the shared bus at a time and that direction changes respect the device’s timing requirements.

🏭

Industrial Control Data Routing

The SN74LS645N is useful in industrial control boards that route byte-wide sensor, actuator, and controller signals between subsystem backplanes. The device’s 20-pin PDIP package is practical for through-hole control hardware, while its eight channels reduce the number of discrete transceivers required for grouped data paths. The 3-state output supports shared-bus arbitration when the controller disables the transceiver outside its active interval. Designers should use a single common ground, terminate signals consistently, and verify timing margins for the control board’s processor and peripheral clocking. Its 5 V supply window and 15 mA sink capability align with conventional 74LS logic rather than low-voltage CMOS interfaces.

🔧

Memory and Peripheral Bus Multiplexing

The SN74LS645N can provide directional routing between a processor bus and a memory or peripheral interface when both sides use compatible 5 V logic. Byte-wide operation allows eight related signals to change direction together, simplifying address, data, or command multiplexing where multiple resources share conductors. The non-inverting paths preserve signal polarity, and the tri-state outputs let the system isolate the device when another resource becomes the active bus owner. Timing remains the principal design constraint: enable and direction controls must not overlap in a way that creates output contention, and the source and destination devices must maintain compatible rise, fall, and propagation timing.

🧩

Legacy Test and Measurement Systems

The SN74LS645N suits legacy test equipment that needs to route eight measurement or control lines between an instrument bus and a device under test. Its bidirectional non-inverting channels accommodate both command transfer and response capture, while the high-impedance output state allows the instrument bus to be shared safely under controlled ownership. The through-hole PDIP package supports repair-oriented and prototype assemblies, and the Schmitt-trigger inputs are beneficial when slower or noisier test-bus wiring is involved. Engineers should add appropriate pull resistors where required by the system architecture and verify that the DUT cannot drive a bus line while the transceiver is actively driving it.

📱

Printer and Peripheral Data Sharing

The SN74LS645N can support a shared peripheral data path in older printer, terminal, or controller assemblies where one bus must connect to more than one 8-bit peripheral. Direction control determines whether commands travel toward the peripheral or data returns toward the controller, and the 3-state output lets each transceiver release the bus when inactive. This arrangement reduces duplicated logic while retaining legacy 74LS interoperability. The implementation must include a deterministic arbitration mechanism to prevent two peripherals from driving simultaneously. Cable or board-trace loading, grounding, and logic thresholds should be evaluated before adding long interconnects, since a 5 V TTL bus transceiver is generally better suited to controlled board-level communication than long-distance cabling.

🧩

Embedded 5 V System Interconnect

The SN74LS645N is appropriate for embedded systems that retain a 5 V TTL control domain alongside older memory, display, or expansion hardware. Eight non-inverting channels provide a compact bridge between the embedded controller and a legacy bus without requiring individual buffer packages for every line. The Schmitt-trigger input characteristic provides defined switching behavior, while the 3-state output supports isolation from other bus participants. The SN74LS645N should be powered from a properly decoupled 5 V rail and referenced to the same ground network as the connected devices. Designers must also account for direction-control timing and ensure that any attached device remains high-impedance while the transceiver is driving the corresponding bus.

What is the SN74LS645N?
The SN74LS645N is an 8-bit, non-inverting, 3-state bus transceiver designed for asynchronous two-way data-bus communication. According to the Texas Instruments product page, it belongs to the 74LS bipolar logic family and uses a 20-pin PDIP package. The eight channels can transmit data in either direction and place their outputs in a high-impedance state when disabled, making the device useful for shared buses.
What are the key specifications of SN74LS645N that engineers should know?
The SN74LS645N provides eight non-inverting channels, 3-state outputs, a 4.75 V to 5.25 V operating supply range, Schmitt-trigger inputs, and a 20-pin PDIP package. Texas Instruments describes the device as an octal bus transceiver, while the manufacturer datasheet identifies 15 mA output sink capability. These characteristics place it in the 74LS TTL-compatible interface family for legacy 5 V systems.
What is the operating voltage of SN74LS645N?
The SN74LS645N operates from 4.75 V to 5.25 V according to the Texas Instruments SN74LS645 documentation referenced by the component comparison record. This range is the nominal 5 V TTL operating window. The device should not be operated below 4.75 V or above 5.25 V without consulting the complete manufacturer datasheet and verifying absolute-maximum ratings.
Where can I download the SN74LS645N datasheet PDF?
The official Texas Instruments SN74LS645 datasheet and supporting product information are available from the manufacturer product page at https://www.ti.com/product/SN74LS645. The manufacturer page provides the authoritative electrical characteristics, ordering information, pin configuration, and package details for the SN74LS645 family, including the SN74LS645N PDIP ordering option.
Where is the SN74LS645N pinout?
The SN74LS645N pinout is defined in the pin-configuration section of the Texas Instruments SN74LS645 datasheet. The component uses a 20-pin PDIP package with eight A-side and eight B-side bus connections, plus common enable and direction-control functions. Use the manufacturer pin table when assigning PCB tracks because signal names and enable polarity must be checked against the exact device revision.
Is SN74LS645N suitable for a bidirectional 8-bit bus?
Yes, the SN74LS645N is specifically designed for an asynchronous, bidirectional eight-bit bus. Its non-inverting channels transfer data in either direction, while the 3-state outputs allow the device to relinquish bus ownership. The Texas Instruments product page identifies the SN74LS645 as an octal bus transceiver, and the 15 mA output sink specification supports conventional 74LS-style loading.
What can replace the SN74LS645N?
The SN74LS645-1N is a documented pin-compatible replacement candidate for the SN74LS645N because both use the 20-pin PDIP format and share the same SN74LS645 bus-transceiver function. The replacement record describes their terminals and packages as consistent. Confirm direction, enable, timing, and electrical limits in the manufacturer datasheet before using it in production equipment.
Is SN74LS645N the same as SN74LS645-1N?
The SN74LS645N and SN74LS645-1N share the same 20-pin PDIP package and the same octal 3-state transceiver function, making the latter a plausible pin-compatible replacement. The cross-reference description reports consistent terminals, packages, and principal performance characteristics. The suffix can still identify a different speed grade, so check propagation-delay requirements before substituting it.
What is the best drop-in replacement for SN74LS645N?
The SN74LS645-1N is the best-supported drop-in replacement candidate identified for the SN74LS645N because the published comparison states that their terminals and packages are consistent. Both use a 20-pin PDIP package and implement an octal 3-state bus transceiver. Verify speed grade, propagation delay, control-pin behavior, and production qualification against the original system requirements.
When should I choose SN74LS645N over SN74LS645-1N?
Choose the SN74LS645N when the original design specifies the standard SN74LS645-1N-compatible option and the required bus timing is satisfied by the standard grade. Choose SN74LS645-1N when the replacement record’s consistent package and terminals are confirmed and its speed-grade characteristics meet the original timing budget. Both are 20-pin PDIP devices intended for the same 4.75 V to 5.25 V interface environment.
SN74LS645N vs SN74LS645-1N: which is better for legacy equipment?
The SN74LS645-1N is the stronger candidate for an exact drop-in repair when the original equipment requires a speed grade compatible with the published SN74LS645-1N designation. The SN74LS645N remains the standard family option and shares the 20-pin PDIP footprint. Neither should be selected solely from the suffix; compare the manufacturer timing limits and the original board’s bus requirements.
What is the difference between SN74LS645N and SN74LS646N?
The SN74LS646N is identified as a related transceiver with the same functionality and package, but it belongs to the SN74LS646 family and may use a different output implementation. Its package similarity alone does not establish safe drop-in compatibility. Confirm the output-stage topology, enable behavior, and pin definitions in the manufacturer datasheet before using it as a replacement for the SN74LS645N.
What is the difference between SN74LS645N and SN74LS640N?
The SN74LS645N is an octal, non-inverting, 3-state bus transceiver, whereas the SN74LS640 belongs to a related 74LS bus-interface family with different bus-driver characteristics. The comparison record does not establish that the SN74LS640N is pin-to-pin interchangeable. Use the SN74LS645N only where its 20-pin pinout, direction control, output enable, and output-stage behavior match the original circuit.
Can I buy SN74LS645N online?
Yes, XAIPART provides a Request a Quote form on this page for SN74LS645N purchasing inquiries, including current availability, lead time, and order confirmation. The manufacturer lists the SN74LS645 family on its official product page, while a distributor listing identifies the SN74LS645N as a 20-pin PDIP octal bus transceiver. Submit the exact MPN when requesting a quotation.
What is the price of SN74LS645N?
The current commercial terms for SN74LS645N are provided through XAIPART’s Request a Quote form on this page. Use the exact MPN SN74LS645N and the required quantity when requesting current pricing, stock confirmation, lead time, and shipment options. The form avoids presenting a static price that may not reflect the selected quantity or current component availability.
What is the lead time for SN74LS645N?
The current lead time for SN74LS645N depends on manufacturer inventory, packaging requirements, and order volume. Request a quotation through the Request a Quote form on this page and state the required quantity, ship-to location, and acceptable delivery date. The manufacturer product page and distributor listing can be used to confirm the family identity while the commercial confirmation is obtained.
Is SN74LS645N in stock?
Stock availability for SN74LS645N should be confirmed through the Request a Quote form on this page because inventory can change by quantity and package. A distributor listing identifies the exact 20-pin PDIP ordering option, but the current stock message should not replace a quantity-specific quotation. Provide the required order quantity to receive the most useful confirmation.

Data referensi kejuruteraan untuk SN74LS645N — perbandingan, panduan rancangan, dan maklumat kesediaan

Panduan Pilihan

Choose the SN74LS645N for a legacy 5 V system that requires eight non-inverting, bidirectional data channels with 3-state outputs and a 20-pin PDIP footprint. Its 4.75 V to 5.25 V supply range, Schmitt-trigger inputs, and 15 mA sink capability suit established 74LS bus architectures. Select SN74LS645-1N when its documented consistent terminals and packages make it the appropriate speed-grade option for the target equipment, but verify propagation timing before substitution. The SN74LS646N and SN74LS640N belong to related 74LS families, but package similarity alone does not prove safe interchangeability because output-stage and control behavior can differ. For new designs, compare these legacy bipolar devices with modern low-voltage CMOS bus transceivers when voltage, speed, supply current, and signal standards permit.

Perbandingan dengan Gantian

Parametr Produk Ini SN74LS645-1N
Package 20-pin PDIP 20-pin PDIP
Brand Texas Instruments Texas Instruments
Function Octal bus transceiver Octal bus transceiver
Number of Channels 8 bits 8 bits
Data Direction Non-inverting Non-inverting
Output State 3-state 3-state
Supply Voltage 4.75 V to 5.25 V 4.75 V to 5.25 V
Input Type Schmitt trigger Schmitt trigger
Output Sink Current 15 mA 15 mA

Penyeberangsung Jelas

  • Exact 20-pin PDIP replacement path (vsSN74LS645-1N)
  • Eight parallel bidirectional channels (vsSN74LS245N)
  • Compatible 5 V interface environment (vsSN74LS640N)

Catatan Desain

Never allow two 74LS bus drivers to enable the same shared line simultaneously. Output contention can produce excessive current and undefined voltage levels even when the data inputs agree. Use the enable and direction controls so that ownership changes only after the previous driver has entered its 3-state interval, and include the relevant timing limits from the manufacturer datasheet in the system timing budget.

Place the supply bypass capacitor close to the transceiver’s supply pins and connect it to a low-impedance ground plane. Keep the eight A-side and B-side routes physically compact, and route the corresponding pairs with similar geometry to limit skew between byte lanes. In through-hole designs, minimize stub branches from the shared bus because excessive loading can reduce noise margin and upset the 74LS timing budget.

Use the Schmitt-trigger input characteristic to improve tolerance of slow or noisy transitions, but do not treat it as a substitute for sound signal-integrity design. Maintain a common ground reference between communicating devices, avoid long unterminated branches, and verify rise-time, propagation-delay, and setup requirements at the actual bus clock rate. The manufacturer datasheet should govern any termination values and timing assumptions.

The SN74LS645N is intended for a 4.75 V to 5.25 V operating range, so the system should provide a stable 5 V rail rather than an unregulated source. Check the supply ramp, noise, and ground-return paths, especially when the transceiver is enabled during system startup. Confirm device-specific current and absolute-maximum limits in the complete manufacturer documentation before adding external loading.

Maklumat Kesediaan

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Bosong logam timbal
Unknown
Bosong halogen
Unknown
Mineral konflik
Unknown

The manufacturer product page and component listings do not state the requested compliance certifications. AEC-Q100 is not applicable to this general-purpose 74LS logic device.

Data disahkan pada: 2026-11-18 — data yang disahkan dan disusun semula oleh pasukan kejuruteraan komponen XAIPART

Pencarian Berhubungan

sn74ls645n datasheet SN74LS645N pinout SN74LS645N datasheet pdf SN74LS645N replacement SN74LS645N equivalent SN74LS645N 20 pin PDIP SN74LS645N vs SN74LS645-1N SN74LS645N price SN74LS645N stock Texas Instruments SN74LS645N SN74LS645N application circuit SN74LS645N 3-state bus

Komponen dan Tanda berkaitan

Texas Instruments SN74LS645N SN74LS645 SN74LS645-1N SN74LS646N SN74LS640N SN74LS245N Octal bus transceiver Bidirectional transceiver Interface IC Semiconductor 74LS bipolar TTL Non-inverting logic 3-state output High-impedance state Schmitt trigger Asynchronous data bus 20-pin PDIP DIP package Through-hole technology Surface mount technology 5 V logic Byte-wide data transfer Bus contention
RFRC Saring Pantas
Isikan butiran lengkap — pasukan jualan kami akan bertindak balas dalam masa 24 jam
Nombor Bahagian Pengeluar Pakej QTY Harga Target Lengkap
✓
Pesan diskon sudah disubmit!

Kami akan bertindak balas kepada emel anda dalam tempoh 24 jam

1
RFQ Diserahkan
2
kutipan Diterima
3
Order Dipesan
4
Pembayaran
5
Dihantar
6
Diantar
Lihat Perincian RFQ