SN75118N - 5V Differential Line Transceiver | Texas Instruments
N.º de pieza: SN75118N ✓ ActivoSN75118N Descripción general
The transceiver is designed to place a TTL or CMOS-style logic signal onto a differential line and recover a logic-level output from the differential signal arriving on the same bus. Differential signaling rejects common-mode noise and improves noise immunity when the two line conductors receive equal interference. The driver's 3-state output can be released for party-line operation, preventing a disabled node from blocking the shared bus while another node transmits.
The SN75118N family is intended for point-to-point and multipoint data-bus interfaces rather than modern high-rate LAN or automotive Ethernet links. Its differential driver, receiver, and control architecture allow a controller to manage transmit and receive paths within one device. Because it is a legacy bipolar-era interface IC, the design must account for the electrical limits and operating conditions stated in the manufacturer datasheet rather than assuming compatibility with contemporary RS-485 or RS-422 transceivers.
The SN75118 is identified by Texas Instruments as a differential line transceiver. The N ordering code denotes the 16-pin PDIP package, measuring 19.3 mm by 9.4 mm with a stated body area of 181.42 mm². The device operates from a single 5 V supply and provides a driver input that accepts TTL-compatible logic levels, a receiver output that drives TTL-compatible logic levels, and a three-state driver output suitable for shared-bus designs.
Typical uses include industrial data acquisition, telemetry interfaces, test and measurement equipment, multipoint control buses, and legacy communications equipment. The SN75118N is most appropriate where a 5 V TTL system must connect to a differential line and where transmitter disable and receiver enable functions are required. It is also suitable for systems that need a shared bus rather than a dedicated point-to-point link.
When laying out a circuit around the SN75118N, route the differential pair together, keep the driver output in a high-impedance state whenever the node is not transmitting, and follow the receiver-enable polarity shown in the manufacturer pin description table. Confirm the bias and termination arrangement for the specific line length and data rate, because the device is a general-purpose differential transceiver rather than a network PHY with integrated cable compensation.
This page organizes the SN75118N specifications, verified sourcing references, and design considerations into a single engineering reference. It also distinguishes the N-package ordering option from related family members whose receiver-control arrangements and package formats differ, helping engineers determine whether a substitute is genuinely pin-to-pin compatible before committing to a PCB change.
Alternativas directas para SN75118N — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con SN75118N (mismo factor de forma y huella) — difiere en Primary Application.
SN75118NE4
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
SN75118N Especificaciones
| Product Type | Differential line transceiver |
| Tensión de alimentación | 5 V |
| Driver Input Logic Compatibility | TTL-compatible |
| Receiver Output Logic Compatibility | TTL-compatible |
| Driver Output State Capability | 3-state |
| Line Signal Type | Differential |
| Receiver Control | Enable input |
| Primary Application | Party-line and data-bus interfacing |
| Encapsulado | PDIP (N), 16 pins |
| Package Body Length | 19.3 mm |
| Package Body Width | 9.4 mm |
| Package Body Area | 181.42 mm2 |
| Tipo de montaje | Through-hole |
Guía de configuración de pines de SN75118N 181.42 mm2
Configuración de pines para SN75118N (encapsulado 181.42 mm2). La numeración de pines, las funciones y los diagramas de conexión se definen en la hoja de datos del fabricante. Consúltela para conocer el footprint exacto y las directrices de soldadura.
No hay datos detallados de patillaje disponibles para SN75118N.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
SN75118N es adecuado para 6 aplicacións: Legacy TTL-to-Differential Control Bus, Party-Line Data Acquisition, Telemetry and Remote Sensor Interface, Test and Measurement Front End, Multipoint Industrial Bus Backplane, Legacy Communication Equipment Retrofit.
Legacy TTL-to-Differential Control Bus
The SN75118N fits legacy control systems in which 5 V TTL logic must communicate over a balanced pair rather than directly over a single-ended line. Its TTL-compatible driver input accepts the controller's logic signal, while the differential receiver produces a TTL-compatible output for the receiving side. Differential signaling improves common-mode noise rejection and allows the bus to operate reliably closer to noisy switching circuitry than a single-ended interface. The three-state driver also supports shared-bus arrangements where each node must disconnect electrically while it is not transmitting.
Recomendado
Party-Line Data Acquisition
The SN75118N is appropriate for a party-line acquisition system in which several remote modules share one differential data pair. One node can drive the bus while the others hold their three-state outputs inactive, preventing an unpowered or idle node from obstructing communication. The receiver path provides a separate logic output, and the enable input allows the receiving function to be disabled during periods when the node does not need data. In such systems, connector wiring, node isolation during power-up, and controlled bus-ownership timing are as important as the transceiver itself.
Recomendado
Telemetry and Remote Sensor Interface
The SN75118N can bridge a 5 V controller to a remote differential telemetry link where common-mode noise is a concern. The transmitter converts a TTL-level command into a differential output, while the receiver reconstructs a logic signal from the returning differential pair. This arrangement is useful in industrial monitoring equipment that distributes measurements over cables running near motors, relays, and switching supplies. Because the SN75118N is a legacy general-purpose transceiver, the interface should include suitable surge protection and verified cable termination rather than assuming modern network-transceiver protections.
Recomendado
Test and Measurement Front End
The SN75118N is useful in legacy test and measurement equipment where a controller drives remote instrument commands over a differential pair and reads back a differential response. The separate driver and receiver paths allow full-duplex-style point-to-point communication within a single package, while the three-state driver offers additional bus flexibility. Its 16-pin PDIP format is also convenient for through-hole prototype construction and repair of older measurement platforms. Designers should still budget board area, insertion cost, and legacy component availability when deciding whether to maintain or redesign the platform.
Recomendado
Multipoint Industrial Bus Backplane
The SN75118N can be integrated into a multipoint industrial backplane where several modules communicate over a shared differential pair. Its three-state output lets a node release the bus during another node's transmission, while the differential receiver improves tolerance to noise coupled equally into both conductors. This topology is most appropriate for slow or moderate-rate control traffic in established equipment rather than new high-speed factory networks. Firmware or hardware must guarantee that only one node drives the pair at a time to prevent output contention.
Recomendado
Legacy Communication Equipment Retrofit
The SN75118N is a practical choice when repairing or extending older communication equipment that uses a 5 V differential line transceiver in a 16-pin PDIP socket. Repair teams can preserve the original board architecture by matching the enable behavior, differential polarity, and logic levels of the installed device. The DIP package also simplifies inspection, socket replacement, and rework compared with a fine-pitch surface-mount alternative. Before ordering, verify that the replacement is the PDIP N option rather than a surface-mount ordering suffix with a different footprint.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para SN75118N — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | SN75118NE4 |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | PDIP-16 | PDIP-16 |
| Function | Differential line transceiver | Differential line transceiver |
| Supply Voltage | 5 V | 5 V |
| Driver Input Compatibility | TTL-compatible | TTL-compatible |
| Receiver Output Compatibility | TTL-compatible | TTL-compatible |
| Driver Output State | 3-state | 3-state |
| Receiver Control | Enable input | Enable input |
| Line Mode | Differential | Differential |
| Target Application | Party-line and data-bus interfacing | Party-line and data-bus interfacing |
Diferenciadores clave
- Receiver-enable control supports deliberate receive-path shutdown (frente a SN75116)
- Integrated differential driver and receiver in one 5 V device (frente a MC1489NE4)
- Through-hole PDIP construction supports serviceable legacy boards (frente a SN75118NSRG4)
Notas de diseño
Route the SN75118N differential pair as a closely coupled pair on a continuous reference plane, keeping the two conductors over similar impedances and away from switching nodes, relays, and high-current return paths. Place the line-side protection and termination components near the cable connector so surge current is diverted before it reaches the IC. Because the device is intended for 5 V legacy systems, verify the connector's ground reference and any common-mode voltage excursion against the receiver's absolute maximum and common-mode limits in the manufacturer datasheet.
Do not allow two nodes to drive the shared differential pair simultaneously. In a party-line design, the host or node controller must guarantee that only one 3-state driver is enabled at a time and that disabled outputs reach a genuine high-impedance state. Also avoid substituting an RS-485 transceiver solely because both devices are described as differential transceivers: the SN75118N uses receiver-enable control, whereas common RS-485 pinouts assign the second control input to driver enable, so an incorrect substitution can prevent transmitter operation or disable the wrong path.
Decouple the 5 V supply at the device with a short, low-inductance connection to the ground reference used by the interface. Avoid routing return current from the differential line through logic-supply paths, and keep the transceiver ground connection close to its supply and driver-return requirements. Estimated: if the device dissipates 50 mW at a 5 V rail and ambient is 25 C, a modest DIP-package thermal rise of roughly 5 C to 10 C is typical, but actual junction temperature depends on the manufacturer's power rating and board copper.
Información de cumplimiento
The manufacturer product and distributor records confirm the device function, package, and electrical feature set but do not state RoHS, REACH, halogen-free, or conflict-minerals status. AEC-Q100 is not applicable because the SN75118N is a general-purpose commercial interface device rather than an automotive-qualified variant.