Texas Instruments

SN75118N - 5V Differential Line Transceiver | Texas Instruments

MPN: SN75118N ✓ Aktif
5 V Vdss PDIP (N), 16 pins Package
MOQ: 1 |

SN75118N Ringkasan

The Texas Instruments SN75118N is a 5 V differential line transceiver that combines a 3-state differential line driver and a differential-input line receiver in a 16-pin PDIP package. It interfaces TTL-type digital systems with balanced data-transmission lines and supports party-line or data-bus arrangements where multiple nodes share one differential pair. Its single 5 V supply, TTL-compatible driver inputs, TTL-compatible receiver output, and separate receiver enable control make it suitable for legacy industrial, communications, instrumentation, and data-acquisition equipment. The SN75118N uses an enable input on the receiver rather than the receiver strobe arrangement used by the related SN75117, allowing the receiving path to be disabled independently of the driver output.

The transceiver is designed to place a TTL or CMOS-style logic signal onto a differential line and recover a logic-level output from the differential signal arriving on the same bus. Differential signaling rejects common-mode noise and improves noise immunity when the two line conductors receive equal interference. The driver's 3-state output can be released for party-line operation, preventing a disabled node from blocking the shared bus while another node transmits.

The SN75118N family is intended for point-to-point and multipoint data-bus interfaces rather than modern high-rate LAN or automotive Ethernet links. Its differential driver, receiver, and control architecture allow a controller to manage transmit and receive paths within one device. Because it is a legacy bipolar-era interface IC, the design must account for the electrical limits and operating conditions stated in the manufacturer datasheet rather than assuming compatibility with contemporary RS-485 or RS-422 transceivers.

The SN75118 is identified by Texas Instruments as a differential line transceiver. The N ordering code denotes the 16-pin PDIP package, measuring 19.3 mm by 9.4 mm with a stated body area of 181.42 mm². The device operates from a single 5 V supply and provides a driver input that accepts TTL-compatible logic levels, a receiver output that drives TTL-compatible logic levels, and a three-state driver output suitable for shared-bus designs.

Typical uses include industrial data acquisition, telemetry interfaces, test and measurement equipment, multipoint control buses, and legacy communications equipment. The SN75118N is most appropriate where a 5 V TTL system must connect to a differential line and where transmitter disable and receiver enable functions are required. It is also suitable for systems that need a shared bus rather than a dedicated point-to-point link.

When laying out a circuit around the SN75118N, route the differential pair together, keep the driver output in a high-impedance state whenever the node is not transmitting, and follow the receiver-enable polarity shown in the manufacturer pin description table. Confirm the bias and termination arrangement for the specific line length and data rate, because the device is a general-purpose differential transceiver rather than a network PHY with integrated cable compensation.

This page organizes the SN75118N specifications, verified sourcing references, and design considerations into a single engineering reference. It also distinguishes the N-package ordering option from related family members whose receiver-control arrangements and package formats differ, helping engineers determine whether a substitute is genuinely pin-to-pin compatible before committing to a PCB change.

Pilihan pengganti yang segera untuk SN75118N — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.

Varietas dalam siri ini

Model serupa yang kompatibel dengan pengganti yang segera SN75118N (sama faktor bentuk dan kaki) — berbeza dalam Primary Application.

Texas Instruments
Primary Application: Party-line and data-bus communication
Bandingkan Dengan SN75118N →

SN75118NE4

✅ Masuk Drop-In
📦 PDIP-16
Same SN75118 function and 16-pin PDIP format; NE4 identifies a different ordering suffix, with no functional difference identified in the verified cross-reference listing

📋 Alternatif rujukan (tidak dalam katalog)

SN75118N Spesifikasi

Product Type Differential line transceiver
Tegangan Pemberi Arus 5 V
Driver Input Logic Compatibility TTL-compatible
Receiver Output Logic Compatibility TTL-compatible
Driver Output State Capability 3-state
Line Signal Type Differential
Receiver Control Enable input
Primary Application Party-line and data-bus interfacing
Kemasan PDIP (N), 16 pins
Package Body Length 19.3 mm
Package Body Width 9.4 mm
Package Body Area 181.42 mm2
Jenis Pemasangan Through-hole

Panduan Konfigurasi Pin SN75118N 181.42 mm2

Konfigurasi pin untuk SN75118N (181.42 mm2 pakai). Penomeran pin, fungsi, dan garis bentuk koneksi ditakrifkan dalam dokumen pengeluar. Rujuk dokumen untuk kebentuk dan pedoman pengasman.

Garis bentuk pengecah pakai 181.42 mm2 untuk SN75118N

Tiada data garisan pin yang diperoleh untuk SN75118N.

Rujuk kepada lembaran data untuk konfigurasi pin penuh.

Aplikasi Biasa

SN75118N patut untuk 6 aplikasis: Legacy TTL-to-Differential Control Bus, Party-Line Data Acquisition, Telemetry and Remote Sensor Interface, Test and Measurement Front End, Multipoint Industrial Bus Backplane, Legacy Communication Equipment Retrofit.

🏭

Legacy TTL-to-Differential Control Bus

The SN75118N fits legacy control systems in which 5 V TTL logic must communicate over a balanced pair rather than directly over a single-ended line. Its TTL-compatible driver input accepts the controller's logic signal, while the differential receiver produces a TTL-compatible output for the receiving side. Differential signaling improves common-mode noise rejection and allows the bus to operate reliably closer to noisy switching circuitry than a single-ended interface. The three-state driver also supports shared-bus arrangements where each node must disconnect electrically while it is not transmitting.

📡

Party-Line Data Acquisition

The SN75118N is appropriate for a party-line acquisition system in which several remote modules share one differential data pair. One node can drive the bus while the others hold their three-state outputs inactive, preventing an unpowered or idle node from obstructing communication. The receiver path provides a separate logic output, and the enable input allows the receiving function to be disabled during periods when the node does not need data. In such systems, connector wiring, node isolation during power-up, and controlled bus-ownership timing are as important as the transceiver itself.

🧩

Telemetry and Remote Sensor Interface

The SN75118N can bridge a 5 V controller to a remote differential telemetry link where common-mode noise is a concern. The transmitter converts a TTL-level command into a differential output, while the receiver reconstructs a logic signal from the returning differential pair. This arrangement is useful in industrial monitoring equipment that distributes measurements over cables running near motors, relays, and switching supplies. Because the SN75118N is a legacy general-purpose transceiver, the interface should include suitable surge protection and verified cable termination rather than assuming modern network-transceiver protections.

🖥️

Test and Measurement Front End

The SN75118N is useful in legacy test and measurement equipment where a controller drives remote instrument commands over a differential pair and reads back a differential response. The separate driver and receiver paths allow full-duplex-style point-to-point communication within a single package, while the three-state driver offers additional bus flexibility. Its 16-pin PDIP format is also convenient for through-hole prototype construction and repair of older measurement platforms. Designers should still budget board area, insertion cost, and legacy component availability when deciding whether to maintain or redesign the platform.

🔗

Multipoint Industrial Bus Backplane

The SN75118N can be integrated into a multipoint industrial backplane where several modules communicate over a shared differential pair. Its three-state output lets a node release the bus during another node's transmission, while the differential receiver improves tolerance to noise coupled equally into both conductors. This topology is most appropriate for slow or moderate-rate control traffic in established equipment rather than new high-speed factory networks. Firmware or hardware must guarantee that only one node drives the pair at a time to prevent output contention.

🔧

Legacy Communication Equipment Retrofit

The SN75118N is a practical choice when repairing or extending older communication equipment that uses a 5 V differential line transceiver in a 16-pin PDIP socket. Repair teams can preserve the original board architecture by matching the enable behavior, differential polarity, and logic levels of the installed device. The DIP package also simplifies inspection, socket replacement, and rework compared with a fine-pitch surface-mount alternative. Before ordering, verify that the replacement is the PDIP N option rather than a surface-mount ordering suffix with a different footprint.

What is the SN75118N used for?
The SN75118N is a 5 V differential line transceiver used to connect TTL-compatible digital logic to a differential data line. It combines a 3-state differential line driver with a differential-input receiver in one 16-pin PDIP package. Texas Instruments describes the device for party-line and data-bus applications where multiple nodes may share the same pair of conductors.
Is the SN75118N pin-compatible with an RS-485 transceiver?
No, the SN75118N should not be assumed to be pin-compatible with a standard RS-485 transceiver. The SN75118N is identified as a general-purpose differential line transceiver with an enable-controlled receiver, while RS-485 devices commonly use a driver-enable input and a receiver-enable input with different pin assignments. Verify the complete pin-description table before treating any RS-485 device as a substitute.
What is the difference between the SN75118 and SN75117?
The principal functional difference is the receiver-control arrangement: the SN75118 uses a receiver enable input, whereas the SN75117 uses a receiver output strobe. Both devices are differential line transceivers with a 3-state driver and a single 5 V supply. The difference matters in systems where an active-low strobe and a level-controlled enable require different external logic.
Where can I download the SN75118N datasheet PDF?
The official SN75118 datasheet is available from the Texas Instruments product page at https://www.ti.com/product/SN75118, with the direct PDF link listed on this page. The document defines the differential driver and receiver, the receiver-enable function, electrical characteristics, and the 16-pin PDIP pin assignments. Use the manufacturer document for design sign-off and symbol verification.
Where can I find the SN75118N pinout?
The SN75118N pinout is defined in the pin-configuration section of the Texas Instruments SN75118 datasheet. The device is supplied in a 16-pin PDIP package, so the drawing on this page corresponds to that package. Assign PCB signals from the manufacturer's pin-description table and the associated schematic symbol rather than relying on signal-position memory.
What are the key specifications of SN75118N that engineers should know?
The essential SN75118N specifications are a single 5 V supply, a differential 3-state driver, a differential-input receiver with TTL-compatible logic interfaces, and a 16-pin PDIP package. Texas Instruments specifies the device for party-line and data-bus applications. Maximum data rate, input voltage limits, propagation delay, and temperature ratings should be taken from the electrical-characteristics table.
How does the SN75118N support a party-line data bus?
The SN75118N supports a party-line bus by combining a differential driver with a three-state output, allowing an inactive node to present a high-impedance state instead of clamping the shared line. The receiver then recovers a logic output from the differential voltage across the pair. Proper inactive-state control and termination are essential for reliable operation with multiple connected nodes.
Can SN75118N replace SN75118NSRG4?
The SN75118N and SN75118NSRG4 are not direct package-for-package substitutes because their order codes specify different physical packages. The verified cross-reference material lists SN75118NSRG4, but the N and NSRG4 suffixes identify different mounting formats. Confirm the required package, pin count, and board outline before selecting either ordering option.
What is the best drop-in replacement for SN75118N?
The closest documented same-family ordering option is SN75118NE4, which retains the PDIP format represented by the N suffix and is listed in cross-reference results. A truly equivalent drop-in device must match all 16 electrical and control functions, not merely the transceiver category. Because the retrieved material does not identify several independently verified pin-to-pin alternatives, request a manufacturer cross-reference check before approving a substitution.
What can replace SN75118N in an existing design?
A replacement for the SN75118N should provide the same 16-pin PDIP pinout, 5 V operation, differential driver, differential receiver, three-state driver output, and receiver-enable behavior. SN75118NE4 is the nearest same-family candidate identified by the ordering code, while generic RS-485 devices are not automatically interchangeable. Verify timing, input thresholds, output drive, and enable polarity on the manufacturer datasheet.
When should I choose the SN75118N instead of a general RS-485 transceiver?
Choose the SN75118N when the design specifically requires its TTL-compatible logic interface, differential driver and receiver combination, receiver-enable control, and legacy 5 V party-line behavior. Choose a modern RS-485 transceiver when you need standardized network features, higher rates, stronger modern ESD performance, or current multi-drop guidelines. The two device families should not be interchanged solely by function.
Is the SN75118N suitable for industrial data acquisition?
The SN75118N is suitable for many industrial data-acquisition and control systems that use 5 V TTL logic and a dedicated differential line. Its three-state driver allows shared-bus participation, and the differential receiver helps reject common-mode noise. Confirm the industrial temperature grade, isolation needs, ground-reference strategy, and cable-protection requirements before releasing the design.
Does the SN75118N need external line termination?
The termination arrangement depends on the line topology, data rate, cable length, and the specifications of the connected nodes. The SN75118N provides a differential transceiver but does not eliminate the need for a properly engineered bus. Follow the wiring and termination guidance in the manufacturer datasheet and validate the chosen resistor values against the actual cable and node count.
How do I protect the SN75118N in an unprotected outdoor cable interface?
The SN75118N should be protected with appropriately rated surge and ESD protection placed close to the cable connector, with the protection device selected for the signal amplitude and common-mode voltage. Add series impedance or damping where ringing is observed, and keep the protected differential pair away from switching nodes. Confirm the final protection network with the manufacturer's application guidance and system-level tests.
Where to buy SN75118N online and what is its price?
Use the Request a Quote form on this page to request SN75118N pricing, current inventory, minimum order quantity, and lead time. The quantity-break price tables and live stock figures shown by distributors change frequently, so static prices are not reproduced here. Confirm the exact N ordering code, PDIP package, and required shipment quantity in the quote request.
Is the SN75118N in stock and what is the lead time?
Current SN75118N stock and lead time must be confirmed through the Request a Quote form on this page because availability changes with demand and replenishment cycles. Include the required quantity, target date, and confirmation of the PDIP ordering option in the request. Manufacturer lifecycle status and distributor inventory are separate pieces of information and should not be treated as equivalent.

Data referensi kejuruteraan untuk SN75118N — perbandingan, panduan rancangan, dan maklumat kesediaan

Panduan Pilihan

Choose the SN75118N when maintaining or designing a legacy 5 V system that needs a TTL-compatible differential driver and receiver, a three-state output for party-line use, and receiver-enable control. SN75118NE4 is the closest ordering alternative for a board that specifically requires the PDIP format and the same device function. Do not substitute a generic RS-485 transceiver without checking the 16-pin assignment, because receiver-enable and driver-enable roles commonly occupy different pins. Prefer the SN75118N over a surface-mount family member when repairability, socketability, and through-hole assembly are priorities. For new high-speed or standardized industrial networks, a modern RS-485 or RS-422 transceiver is usually the better architectural choice because it offers current multi-drop guidance, stronger protection options, and documented network parameters. For new legacy-protocol extensions, first verify the temperature grade, maximum data rate, and availability of the exact ordering option.

Perbandingan dengan Gantian

Parametr Produk Ini SN75118NE4
Brand Texas Instruments Texas Instruments
Package PDIP-16 PDIP-16
Function Differential line transceiver Differential line transceiver
Supply Voltage 5 V 5 V
Driver Input Compatibility TTL-compatible TTL-compatible
Receiver Output Compatibility TTL-compatible TTL-compatible
Driver Output State 3-state 3-state
Receiver Control Enable input Enable input
Line Mode Differential Differential
Target Application Party-line and data-bus interfacing Party-line and data-bus interfacing

Penyeberangsung Jelas

  • Receiver-enable control supports deliberate receive-path shutdown (vsSN75116)
  • Integrated differential driver and receiver in one 5 V device (vsMC1489NE4)
  • Through-hole PDIP construction supports serviceable legacy boards (vsSN75118NSRG4)

Catatan Desain

Route the SN75118N differential pair as a closely coupled pair on a continuous reference plane, keeping the two conductors over similar impedances and away from switching nodes, relays, and high-current return paths. Place the line-side protection and termination components near the cable connector so surge current is diverted before it reaches the IC. Because the device is intended for 5 V legacy systems, verify the connector's ground reference and any common-mode voltage excursion against the receiver's absolute maximum and common-mode limits in the manufacturer datasheet.

Do not allow two nodes to drive the shared differential pair simultaneously. In a party-line design, the host or node controller must guarantee that only one 3-state driver is enabled at a time and that disabled outputs reach a genuine high-impedance state. Also avoid substituting an RS-485 transceiver solely because both devices are described as differential transceivers: the SN75118N uses receiver-enable control, whereas common RS-485 pinouts assign the second control input to driver enable, so an incorrect substitution can prevent transmitter operation or disable the wrong path.

Decouple the 5 V supply at the device with a short, low-inductance connection to the ground reference used by the interface. Avoid routing return current from the differential line through logic-supply paths, and keep the transceiver ground connection close to its supply and driver-return requirements. Estimated: if the device dissipates 50 mW at a 5 V rail and ambient is 25 C, a modest DIP-package thermal rise of roughly 5 C to 10 C is typical, but actual junction temperature depends on the manufacturer's power rating and board copper.

Maklumat Kesediaan

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Bosong logam timbal
Unknown
Bosong halogen
Unknown
Mineral konflik
Unknown

The manufacturer product and distributor records confirm the device function, package, and electrical feature set but do not state RoHS, REACH, halogen-free, or conflict-minerals status. AEC-Q100 is not applicable because the SN75118N is a general-purpose commercial interface device rather than an automotive-qualified variant.

Data disahkan pada: 2026-11-09 — data yang disahkan dan disusun semula oleh pasukan kejuruteraan komponen XAIPART

Pencarian Berhubungan

SN75118N datasheet SN75118N pinout SN75118 datasheet pdf SN75118N equivalent SN75118N replacement SN75118N vs SN75118NE4 SN75118N DIP-16 transceiver SN75118N 5V differential line transceiver Texas Instruments SN75118N SN75118N price SN75118N stock SN75118N party line application circuit

Komponen dan Tanda berkaitan

Texas Instruments SN75118 SN75118N SN75118NE4 SN75118NSRG4 differential line transceiver differential line driver differential-input line receiver three-state output TTL-compatible logic party-line bus data-bus interface receiver enable single 5 V supply PDIP-16 through-hole package common-mode noise rejection multi-point communication industrial telemetry test and measurement RS-485 RS-422 line termination surge protection
RFRC Saring Pantas
Isikan butiran lengkap — pasukan jualan kami akan bertindak balas dalam masa 24 jam
Nombor Bahagian Pengeluar Pakej QTY Harga Target Lengkap
✓
Pesan diskon sudah disubmit!

Kami akan bertindak balas kepada emel anda dalam tempoh 24 jam

1
RFQ Diserahkan
2
kutipan Diterima
3
Order Dipesan
4
Pembayaran
5
Dihantar
6
Diantar
Lihat Perincian RFQ